Cleanup rules.mk for 32U4 keyboards, T-Z (#7190)

* Cleanup rules.mk for 32U4 keyboards, T-Z

* Use atmel-dfu in place of lufa-ms until it exists

2 files changed, 2 insertions, 43 deletions

diff --git a/keyboards/treadstone32/keymaps/default/rules.mk b/keyboards/treadstone32/keymaps/default/rules.mk
index 8c4541fa19..5ca4c52586 100644
--- a/keyboards/treadstone32/keymaps/default/rules.mk
+++ b/keyboards/treadstone32/keymaps/default/rules.mk
@@ -1,10 +1,7 @@
-
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically
 #
-TAP_DANCE_ENABLE = no
-
 # If your custom treadstone32 pcb, you can rewrite to yes.
 RGBLIGHT_ENABLE = yes  # LED underglow (Enable WS2812 RGB underlight.)
 LED_ANIMATIONS = yes        # LED animations
@@ -20,6 +17,3 @@ endif
 ifeq ($(strip $(IOS_DEVICE_ENABLE)), yes)
     OPT_DEFS += -DIOS_DEVICE_ENABLE
 endif
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
diff --git a/keyboards/treadstone32/rules.mk b/keyboards/treadstone32/rules.mk
index 1d37dfc69f..dbc46b403c 100644
--- a/keyboards/treadstone32/rules.mk
+++ b/keyboards/treadstone32/rules.mk
@@ -1,50 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Build Options
 #   change yes to no to disable
 #
@@ -61,4 +27,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.
 LEADER_ENABLE = no
-