From b47c10bf6f152d7a5c35fc4f7478aa69e91fb081 Mon Sep 17 00:00:00 2001 From: fauxpark Date: Wed, 30 Oct 2019 15:27:25 +1100 Subject: Cleanup rules.mk for 32U4 keyboards, T-Z (#7190) * Cleanup rules.mk for 32U4 keyboards, T-Z * Use atmel-dfu in place of lufa-ms until it exists --- keyboards/treadstone32/keymaps/default/rules.mk | 6 ---- keyboards/treadstone32/rules.mk | 39 ++----------------------- 2 files changed, 2 insertions(+), 43 deletions(-) (limited to 'keyboards/treadstone32') diff --git a/keyboards/treadstone32/keymaps/default/rules.mk b/keyboards/treadstone32/keymaps/default/rules.mk index 8c4541fa19..5ca4c52586 100644 --- a/keyboards/treadstone32/keymaps/default/rules.mk +++ b/keyboards/treadstone32/keymaps/default/rules.mk @@ -1,10 +1,7 @@ - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically # -TAP_DANCE_ENABLE = no - # If your custom treadstone32 pcb, you can rewrite to yes. RGBLIGHT_ENABLE = yes # LED underglow (Enable WS2812 RGB underlight.) LED_ANIMATIONS = yes # LED animations @@ -20,6 +17,3 @@ endif ifeq ($(strip $(IOS_DEVICE_ENABLE)), yes) OPT_DEFS += -DIOS_DEVICE_ENABLE endif - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend diff --git a/keyboards/treadstone32/rules.mk b/keyboards/treadstone32/rules.mk index 1d37dfc69f..dbc46b403c 100644 --- a/keyboards/treadstone32/rules.mk +++ b/keyboards/treadstone32/rules.mk @@ -1,50 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change yes to no to disable # @@ -61,4 +27,3 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. LEADER_ENABLE = no - -- cgit v1.2.3