blob: d8b3b31db10b5fb80a951c67c6caf60e3a1cb42b (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage Combined Mass Storage and Keyboard Device Demo
*
* \section Sec_Compat Demo Compatibility:
*
* The following list indicates what microcontrollers are compatible with this demo.
*
* \li Series 7 USB AVRs (AT90USBxxx7)
* \li Series 6 USB AVRs (AT90USBxxx6)
* \li Series 4 USB AVRs (ATMEGAxxU4)
* \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2)
* \li Series AU XMEGA AVRs (ATXMEGAxxxAxU)
* \li Series B XMEGA AVRs (ATXMEGAxxxBx)
* \li Series C XMEGA AVRs (ATXMEGAxxxCx)
*
* \section Sec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this demo.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Classes:</b></td>
* <td>Mass Storage Device \n
* Human Interface Device</td>
* </tr>
* <tr>
* <td><b>USB Subclasses:</b></td>
* <td>Bulk-Only Transport \n
* Keyboard Subclass</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USBIF Mass Storage Standard \n
* USB Bulk-Only Transport Standard \n
* SCSI Primary Commands Specification \n
* SCSI Block Commands Specification \n
* USBIF HID Specification \n
* USBIF HID Usage Tables</td>
* </tr>
* <tr>
* <td><b>Supported USB Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*
* \section Sec_Description Project Description:
*
* Combined Mass Storage and Keyboard demonstration application. This gives a
* simple reference application for implementing a dual class USB Mass Storage
* and USB HID Keyboard device using the basic USB UFI and HID drivers in all
* modern OSes (i.e. no special drivers required).
*
* On start-up the system will automatically enumerate and function as an
* external mass storage device (which may be formatted and used in the same
* manner as commercial USB Mass Storage devices) and a USB keyboard.
*
* You will need to format the mass storage drive upon first run of this
* demonstration - as the device acts only as a data block transport between
* the host and the storage media, it does not matter what file system is used,
* as the data interpretation is performed by the host and not the USB device.
*
* Keys on the USB keyboard can be pressed by moving the board's Joystick.
*
* The USB control endpoint is managed entirely by the library using endpoint
* interrupts, as the INTERRUPT_CONTROL_ENDPOINT option is enabled. This allows for
* the host to reset the Mass Storage device state during long transfers without
* the need for complicated polling logic.
*
* \section Sec_Options Project Options
*
* The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <th><b>Define Name:</b></th>
* <th><b>Location:</b></th>
* <th><b>Description:</b></th>
* </tr>
* <tr>
* <td>TOTAL_LUNS</td>
* <td>AppConfig.h</td>
* <td>Total number of Logical Units (drives) in the device. The total device capacity is shared equally between each drive -
* this can be set to any positive non-zero amount.</td>
* </tr>
* <tr>
* <td>DISK_READ_ONLY</td>
* <td>AppConfig.h</td>
* <td>Configuration define, indicating if the disk should be write protected or not.</td>
* </tr>
*/
|
