1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
|
/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
Copyright 2015 Jack Humbert
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#pragma once
#define PRODUCT Tractyl Manuform(5x6) Proton C
// wiring of each half
#define MATRIX_COL_PINS \
{ B0, B1, B2, B3, B4, B5 }
#define MATRIX_ROW_PINS \
{ B10, B11, B12, A14, A13, A15 }
#define UNUSED_PINS \
{ A0, A2, A7, A8 }
// B2 used for BOOT1, has internal pull down?
// A9 has internal pull-down
// A11 and A12 are used for USB sense. DO NOT USE.
#define DIODE_DIRECTION COL2ROW
// #define USB_VBUS_PIN B10
#define SPLIT_HAND_PIN C14 // high = left, low = right
// WS2812 RGB LED strip input and number of LEDs
#define RGB_DI_PIN A6
#define WS2812_PWM_DRIVER PWMD3 // default: PWMD2
#define WS2812_PWM_CHANNEL 1 // default: 2
#define WS2812_PWM_PAL_MODE 2 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2
//#define WS2812_PWM_COMPLEMENTARY_OUTPUT // Define for a complementary timer output (TIMx_CHyN); omit for a normal timer output (TIMx_CHy).
// #define WS2812_DMA_STREAM STM32_DMA1_STREAM3 // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
#define WS2812_DMA_CHANNEL 3 // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
#define RGBLED_NUM 20
#define RGBLIGHT_SPLIT
#define RGBLED_SPLIT \
{ 10, 10 }
#define DEBUG_LED_PIN C13
/* Audio config */
#define AUDIO_PIN A5
#define AUDIO_PIN_ALT A4
#define AUDIO_PIN_ALT_AS_NEGATIVE
/* serial.c configuration for split keyboard */
#define SERIAL_USART_FULL_DUPLEX // Enable full duplex operation mode.
#define SERIAL_USART_TX_PIN A9
#define SERIAL_USART_RX_PIN A10
#define SERIAL_USART_DRIVER SD1
#define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
#define SERIAL_USART_RX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
#define SERIAL_USART_TIMEOUT 100 // USART driver timeout. default 100
/* i2c config for oleds */
#define I2C_DRIVER I2CD1
#define I2C1_SCL_PIN B6
#define I2C1_SDA_PIN B7
#define I2C1_SCL_PAL_MODE 4
#define I2C1_SDA_PAL_MODE 4
#define I2C1_CLOCK_SPEED 400000
/* encoder config */
#define ENCODERS_PAD_A \
{ A7 }
#define ENCODERS_PAD_B \
{ A8 }
/* spi config for eeprom and pmw3360 sensor */
#define SPI_DRIVER SPID2
#define SPI_SCK_PIN B13
#define SPI_SCK_PAL_MODE 5
#define SPI_MOSI_PIN B15
#define SPI_MOSI_PAL_MODE 5
#define SPI_MISO_PIN B14
#define SPI_MISO_PAL_MODE 5
/* eeprom config */
#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN B8
#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR 8
// #define EXTERNAL_EEPROM_BYTE_COUNT 8196
// #define EXTERNAL_EEPROM_PAGE_SIZE 32
// #define EXTERNAL_EEPROM_ADDRESS_SIZE 2
// #define DEBUG_EEPROM_OUTPUT
/* pmw3360 config */
#define PMW3360_CS_PIN B9
#define PMW3360_SPI_MODE 3
#define PMW3360_SPI_DIVISOR 8
|
