blob: b98cf6761003ec96a9681ff94fa4809b3424d0fd (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
ADB Protocol
============
Resources
---------
Apple IIgs Hardware Reference Second Edition [p80(Chapter6 p121)]
ftp://ftp.apple.asimov.net/pub/apple_II/documentation/Apple%20IIgs%20Hardware%20Reference.pdf
ADB Keycode
http://72.0.193.250/Documentation/macppc/adbkeycodes/
http://m0115.web.fc2.com/m0115.jpg
ADB Signaling
http://kbdbabel.sourceforge.net/doc/kbd_signaling_pcxt_ps2_adb.pdf
ADB Overview & History
http://en.wikipedia.org/wiki/Apple_Desktop_Bus
Microchip Application Note: ADB device(with code for PIC16C)
http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1824&appnote=en011062
AVR ATtiny2131 ADB to PS/2 converter(Japanese)
http://hp.vector.co.jp/authors/VA000177/html/KeyBoardA5DEA5CBA5A2II.html
Pinouts
-------
Female socket from the front
4o o3
2o o1
==
1: Data
2: Power SW(low when press Power key)
3: Vcc(5V)
4: GND
Commands
--------
ADB command is 1byte and consists of 4bit-address, 2bit-command
type and 2bit-register. The commands are always sent by Host.
Command format:
7 6 5 4 3 2 1 0
| | | |------------ address
| |-------- command type
| |---- register
bits commands
------------------------------------------------------
- - - - 0 0 0 0 Send Request(reset all devices)
A A A A 0 0 0 1 Flush(reset a device)
- - - - 0 0 1 0 Reserved
- - - - 0 0 1 1 Reserved
- - - - 0 1 - - Reserved
A A A A 1 0 R R Listen(write to a device)
A A A A 1 1 R R Talk(read from a device)
The command to read keycodes from keyboard is 0x2C which
consist of keyboard address 2 and Talk against register 0.
Address:
2: keyboard
3: mice
Registers:
0: application(keyobard/mice use to store its data.)
1: application
2: application
3: status and command
Communication
-------------
This is a minimum information for keyboard communication.
See "Resources" for detail.
Signaling:
~~~~____________~~||||||||||||__~~~~~_~~|||||||||||||||__~~~~
|800us | |7 Command 0| | | |15-64 Data 0|Stopbit(0)
+Attention | | | +Startbit(1)
+Startbit(1) | +Tlt(140-260us)
+stopbit(0)
Bit cells:
bit0: ______~~~
65 :35us
bit1: ___~~~~~~
35 :65us
bit0 low time: 60-70% of bit cell(42-91us)
bit1 low time: 30-40% of bit cell(21-52us)
bit cell time: 70-130us
[from Apple IIgs Hardware Reference Second Edition]
Criterion for bit0/1:
After 55us if line is low/high then bit is 0/1.
Attention & start bit:
Host asserts low in 560-1040us then places start bit(1).
Tlt(Stop to Start):
Bus stays high in 140-260us then device places start bit(1).
Global reset:
Host asserts low in 2.8-5.2ms. All devices are forced to reset.
Send request from device(Srq):
Device can request to send at commad(Global only?) stop bit.
keep low for 300us to request.
Keyboard data(register0)
This 16bit data can contains 2 keycodes and 2 released flags.
First keycode is palced in upper nibble. When one keyocode is sent,
lower nibble is 0xFF.
Release flag is 1 when key is released.
15 14 . . . . . 8 7 6 . . . . . 0
| |keycode1 | |keycode2
|released(1) |released(1)
Keycodes:
Scancode consists of 7bit keycode and 1bit release flag.
Device can send two keycodes at once. If just one keycode is sent
keycode1 contains it and keyocode2 is 0xFF.
Power switch:
You can read the state from PSW line(active low) however
the switch has a special scancode 0x7F7F, so you can
also read from Data line. It uses 0xFFFF for release scancode.
END_OF_ADB
|
