summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-06-12Fix i2c EEPROM compile issue when Console is enabled (#9186)Drashna Jaelre
* Fix i2c EEPROM compile issue when Console is enabled * Only use if both console and debugging is enabled
2020-06-12Fix SPI EEPROM compile issue when Console is enabled (#9193)Drashna Jaelre
2020-06-12Initial arm serial partially based on old lets split codezvecr
2020-06-12ARM split - Add uart half duplex transport support (#7987)Joel Challis
* ARM split - Add uart half duplex transport support * Fix for f103 * initial full duplex pass * partially remove full duplex * Correct speeds within driver docs Co-authored-by: Nick Brassel <nick@tzarc.org> Co-authored-by: Nick Brassel <nick@tzarc.org> format code according to conventions [skip ci]
2020-06-12Add SPI 25xx EEPROM support. (#8780)Nick Brassel
2020-06-12Fix off by one error with oled_write_raw_P (#9045)Brian Mock
2020-06-12QMK-ify some GPIO macros (#8315)Ryan
2020-06-12Add SPI master for ChibiOS/ARM. (#8779)Nick Brassel
2020-06-12Fix AVR SPI parameter configuration, remove timeouts due to sync protocol. ↵Nick Brassel
(#8775)
2020-06-12spi_master for AVR (#8299)Ryan
* Change _delay_ms/us() to wait_ms/us() * Switch to platform-agnostic GPIO macros * Add AVR spi_master and migrate Adafruit BLE code * Set verbose back to false * Add clock divisor, bit order and SPI mode configuration for init * Add start and stop functions * Move configuration of mode, endianness and speed to `spi_start()` * Some breaks here would be good * Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4) * Remove mode and divisor enums * Add some docs * No hr at EOF * Add links in sidebar
2020-06-12Fix AVR ws2812 when ADDRESS_BASE is non zero (#8646)Joel Challis
* Fix AVR ws2812 when ADDRESS_BASE is non zero * fix port * remove unused function defs
2020-06-12fixed problem with implicit declaration in quantum/rgblight.c (#8406)Casper Weiss Bang
* Update tmk_core/common/progmem.h Co-Authored-By: Ryan <fauxpark@gmail.com> * Update quantum/rgblight.c Co-Authored-By: Ryan <fauxpark@gmail.com> * fixed problem with implicit declaration in quantum/rgblight.c (#8381) Co-authored-by: Ryan <fauxpark@gmail.com>
2020-06-12Initial arm->chibios pass - simplify some platform logic (#8450)Joel Challis
2020-06-12ARM - ADC cleanup (#8385)Joel Challis
* Update switch to array to allow custom values * Add adc keymap * update docs to reflect alignment of default 10 bit * start conversion to USE_ADCVn * samplerate is hella wrong...stub out for now * basic f1 and f4 functionality * Tidy up current changes * Restore old pinToMux function * Add back sample rate for supported platforms * F0 compile fixes * wordsmithery Co-Authored-By: Ryan <fauxpark@gmail.com> * Remove reference to avr only function Co-authored-by: Ryan <fauxpark@gmail.com>
2020-06-12Adding OLED scroll setup functions (#8386)brickbots
* Adding scroll setup functions: * Clarifying values stored in oled_scroll_speed
2020-06-12Remove pro_micro.h (#8374)Ryan
* Remove pro_micro.h * Include quantum.h
2020-06-12Add support for STM32L0/L1 onboard EEPROM. (#8002)Nick Brassel
* Add support for STM32L0/L1 onboard EEPROM. * Update docs/eeprom_driver.md Co-Authored-By: Joel Challis <git@zvecr.com> Co-authored-by: Joel Challis <git@zvecr.com>
2020-06-12Add ADC support for STM32F3 and STM32F0 devices (#7681)Drew Mills
* Add ADC support for STM32F3 and STM32F0 devices * Add section about configration options available to the ARM ADC implementation * Fix STM32 typo
2020-06-12Buffer based OLED panning, write byte to buffer at arbitrary index (#8055)brickbots
* Add buffer based single line pan, arbitrary byte write to buffer * Change dirty mask to inverse of OLED_BLOCK_TYPE for future proofing larger buffer sizes * Updating docs to include new functions * Updating to clarify scroll vs pan
2020-06-12Add f401 and f411 blackpill examples (#7930)Joel Challis
* Add f401 and f411 blackpill examples * Add readme files * Align dfu args with core * Add support for RESET keycode * move STM32_BOOTLOADER_ADDRESS to rules * Update conf files to latest ChibiOS * Update conf files to latest ChibiOS
2020-06-12Clean up includes for glcdfont headers (#7745)Ryan
* Clean up includes for glcdfont headers * Remove pragma once, most of these are not headers * Missed these
2020-06-12PWM DMA based RGB Underglow for STM32 (#7928)Joel Challis
* Add pwm ws2812 driver * Add docs for pwm ws2812 driver * Update ws2812_pwm for ChibiOS 19 Co-Authored-By: Nick Brassel <nick@tzarc.org> Co-authored-by: Nick Brassel <nick@tzarc.org>
2020-06-12Allow for ChibiOS 20.x (master), as well as enabling ChibiOS-Contrib HAL. ↵Nick Brassel
(#8272)
2020-06-122020 February 29 Breaking Changes Update (#8064)James Young
2020-03-26Fix QWIIC OLED for AVR (#7769)Nick Winans
* Fix QWIIC OLED for AVR * Change missed width * width to width * height * Fix typo in comment Co-Authored-By: fauxpark <fauxpark@gmail.com> * Fix last incorrect uses of LCDWIDTH Co-authored-by: Ryan <fauxpark@gmail.com> format code according to conventions [skip ci]
2020-03-26Fix RESET keycode on some STM32F072 keyboards (#8134)Joel Challis
* Add f072 board files with 'enter_bootloader_mode_if_requested' support * rename default f072 board file to GENERIC_STM32_F072XB * Remove board files * Add bootloader def * Update generic f072 board paths * Revert wrong deletion format code according to conventions [skip ci]
2020-02-26Run clang-format manually to fix recently changed files (#7934)Joel Challis
* Run clang-format manually to fix recently changed files * Run clang-format manually to fix recently changed files - revert template files * Run clang-format manually to fix recently changed files - format off for ascii_to_keycode_lut
2020-02-26Fix out of bound OLED font access (#8145)Ted M Lin
* Fix out of bound OLED font access The default font is 1344 bytes, or a total of 224 glyphs (each 6-bytes wide). OLED_FONT_END defaults to 224, which if used will then index off the end of the font array. So either the documentation or code is wrong. Instead of figuring out the rewording of the documentation, just change the OLED_FONT_END default value to 223, to match the documentation and code. * Add static assert to check array size Build bomb if the font array size doesn't match to the defines.
2020-02-26Add thread safety around i2c_master for ChibiOS/ARM.Nick Brassel
2020-02-26Migrate common ld scripts to common location (#7887)Joel Challis
* Migrate common ld scripts to common location * Remove duplicate ld scripts * Update build to look at common ld location
2020-02-26Create central board for bluepillzvecr
2020-02-26Update split serial code to use driver pattern (#7990)Joel Challis
* Move avr serial code to drivers * Update src+= serial.c to driver pattern
2020-02-26Add additional fixes to EEPROM driver selection (#7274) (#266)Drashna Jaelre
* Add additional fixes to EEPROM driver selection (#7274) - uprintf -> dprintf - Fix atsam "vendor" eeprom. - Bump Kinetis K20x to 64 bytes, too. - Rollback Kinetis to 32 bytes as partitioning can only be done once. Add warning about changing the value. - Change RAM-backed "fake" EEPROM implementations to match eeconfig's current usage. - Add 24LC128 by request. * format code according to conventions [skip ci] Co-authored-by: Nick Brassel <nick@tzarc.org> Co-authored-by: QMK Bot <hello@qmk.fm> Co-authored-by: Florian Didron <fdidron@users.noreply.github.com>
2020-02-26Add central location for ChibiOS defines (#7542)Joel Challis
* Add central location for chibios defines * Add central location for chibios defines - actually add files this time.... * Add Copyright header * Update include order to resolve i2cv1 build errors
2020-02-26Apollo (#246)Florian Didron
* Add External EEPROM driver * Add keyboard * Fix i2c address * Revert i2c address for eeprom * Reduce page size for 24LC128 * Disable External EEPROM for now * Fix up RGB Matrix and layout * Cleanup moonlander.c file * Fix led array center * Disable External EEPROM for now * Cleanup and optimization of files * Add and clean up mappings * Enable "ZSA" defaults for Moonlander * Update matrix to use i2c_readReg * Disable render limit for rgb matrix * Update pin controls to GPIO Commands * Add proper changed mechanism * Additional cleanup * Run clang-format on moonlander files * Align keymap * Limit brightness for rgb matrix to 200 To prevent power draw issues * Add USB-IF VID/PID * Add RGB Matrix Sleep code * Enable External EEPROM on Moonlander * Port over Ergodox Expander error handling and retry code * Re-init RGB Matrix drivers when half is reconnected * Add threaded LED display * Correct layer state settings after moonlander_led_task * Update Moonlander to include Oryx configuration * Add webUSB Stuff * Update default keymap * fix: merge conflict Co-authored-by: Drashna Jaelre <drashna@live.com>
2020-01-09fixed I2C driver support for stm32f4 (#7526)yulei
* correct i2c driver for stm32f4 * update pin mode definitions * update macro definition
2020-01-09Improve support and docs for ADC driver (#7191)fauxpark
* Improve support and docs for ADC driver * Comment ADC channels * Move to Makers and Modders section, and fix usage instructions * Flesh out intro * Superscript 328P note * Fix pin_to_mux LUT * Support USB64/1287 as well * analogReadPin() defaults to 0V mux on invalid pin * Update pinToMux() function documentation * Dot * Accept (some of) the `qmk cformat` changes * Do clang-format properly * More wording tweaks * Link to encoder docs
2020-01-09Improvements to Solenoid feature (#7369)Drashna Jaelre
* Error out when Solenid pin is not defined Instead of defaulting to a (literally) random pin, error out instead. Because this pin may be used, or because that pin may not be exposed, or may not exist. * Remove 'SOLENOID_ACTIVE' setting since it's not used * Update documentation
2020-01-09WS2812 Overhaul (#210)Drashna Jaelre
* ARM - ws2812 bitbang (#7173) * Initial ARM bitbang ws2812 driver * Unify chibios platform to run rgblight_task * Remove 'avr only' comments from ws2812 docs * Remove 'avr only' comments from ws2812 docs * Unify chibios platform to run rgblight_task - review comments * Remove debug flags from keymap * Add comments from review * Add defines for STM32L0XX * Attempt to get arm ws2812 working on multiple gcc versions * Support RGBLIGHT_SLEEP when ChibiOS boards suspend (#7280) Copypasta from the AVR suspend implementation with a Teensy-specific hack removed * Unify RGB and RGBW commands (#7297) * Fix unicode in comments Co-Authored-By: fauxpark <fauxpark@gmail.com> * Remove separate RGBW implementation for a unified function * Set White to 0 in RGBW LEDs This is just to get this working, later, proper brightness can be handled elsewhere. * Use us instead of nanoseconds(?) since it renders correctly on web * Remove RGBW function from arm/ws2812.h * Remove RGBW function from arm/ws2812.c * Formatting changes * Add doc info * Remove force of debug on within rgblight - causes lockups waiting for hid_listen (#7330) * Move Ergodox EZ RGB Light code to custom driver (#7309) * Move Ergodox EZ RGB code to custom driver Also implements full addressing of Ergodox EZ's LED Strip, as written by seebs Co-authored-by: Seebs <seebs@seebs.net> * Make Clipping range accessible for custom drivers * Remove RGBW_BB_TWI from driver and docs * Revert changes to clipping range support * Use just rgblight_set instead of full custom driver * Convert to i2c_master commands * Rename rgblight driver and clean up includes * Use White channel on RGBW LEDs * SPI DMA based RGB Underglow for STM32 (#7674) * Initial stash of ws2812 spi driver * Update comment, add sync backup plan * Add testing notes to spi ws2812 driver * Align RGBW error messages Co-authored-by: Joel Challis <git@zvecr.com> Co-authored-by: Jonathan Rascher <jon@bcat.name> Co-authored-by: Florian Didron <fdidron@users.noreply.github.com>
2020-01-09Add backwards compatibility for oled_write_raw_P on ARMzvecr
2020-01-09Adds raw write functions to the OLED driver (#7237)Thomas Baart
* Added oled_write_raw and oled_write_raw_P functions to the OLED driver * Added oled_write_raw method calls to feature_oled_driver.md
2020-01-09Correct ARM STM32 I2C frequency. (#7080)yiancar
It was beleaved that this setting result in a 400Khz I2C bus. This was incorrect, actual frequency measure with a logic analyzer was around 150Khz. This is derived from the excel sheet linked in the .h file. Also confirmed with the ST IDE.
2020-01-06Clean up ISSI driver includes (#7734)fauxpark
* Clean up ISSI driver includes * Missed an endif
2020-01-06IS31FL3733 Dirty page fix (#7079)yiancar
* IS31FL3733 Dirty page fix Function IS31FL3733_update_led_control_registers was never setting update register to false. As a result the led on/off page was being written every transaction even when it was not modified. This is ineficient and causes lots of bandwidth use. -> Fix the IS31FL3733_update_led_control_registers. -> After testing it was evident that failed I2C transactions could corrupt the Led on/off register. -> Update IS31FL3733_write_pwm_buffer and IS31FL3733_write_register functions to return 0 upon succesful tranmission and 1 if any of the transmitions within the function fail. -> Modify IS31FL3733_update_pwm_buffers function so if any of the IS31FL3733_write_pwm_buffer transuction fails, the g_led_control_registers_update_required register is set to true forcing a rewrite of the led on/off register in case it was corrupted. * Minor comment update * Upsie:) * Update is31fl3733.c * Return fix * more return fix * type change * more boolian logic reversal:)
2019-11-04 Refactor ps2avrgb i2c ws2812 to core (#7183)Joel Challis
* Refactor ps2avrgb i2c ws2812 to core * Refactor jj40 to use ws2812 i2c driver * Refactor ps2avrgb template to use ws2812 i2c driver * Add ws2812 stub files * clang-format and driver config * Add ws2812 driver docs * Fix default config values * Update tmk_core/protocol/vusb/main.c Co-Authored-By: Drashna Jaelre <drashna@live.com>
2019-11-04Reduce duplication for ARM/AVR ws2812 RGB Matrix driver (#7180)Joel Challis
* Reduce duplication for ARM/AVR ws2812 rgb_matrix driver * Reduce duplication for ARM/AVR ws2812 rgb_matrix driver - Fix setled_all use of r,g,b
2019-11-04DRV2605L Continuous Haptic Feedback Support (#6461)MechMerlin
* provide means to turn on RTP mode and set the amplitude * new keycode HPT_CONT to turn RTP off/on * introduce new keycodes HPT_CONI, and HPT_COND for Haptic Continuous Increase and Decrease * support for continuous mode amplitude increase and decrease * code cleanup * update docs to reference new keycodes and functionality * don't touch the keymaps * add function prototypes * add proper guards * cleanup guards * remove extra reserved
2019-09-26Fix battery level code in adafruit_ble.cpp (#6648)bwhelm
* Fix battery level code in adafruit_ble.cpp The code in tsk_core/protocol/lufa/adafluit_ble.cpp that polls the battery level for the Adafruit feather BLE controller reads the regulated voltage, not the raw voltage coming from the battery. To do that, the Adafruit Feather docs say you should read from pin A9: https://learn.adafruit.com/adafruit-feather-32u4-basic-proto/power-management#measuring-battery-4-9. (See also https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le/pinouts#logic-pins-2-9.) I'm not sure why, but analogRead(9); doesn't read the correct pin. Checking all available analog pins experimentally, it turns out that analogRead(7); returns the correct value. So the code above should read: state.vbat = analogRead(7); * Update tmk_core/protocol/lufa/adafruit_ble.cpp Co-Authored-By: Drashna Jaelre <drashna@live.com> * Remove old comment * Fix linking error * Remove `#ifdef` around `#include analog.h`. * Really fix linking error
2019-09-26Removed prescaler define from avr i2c, as it was impossible to use (#6617)Mikkel Jeppesen
2019-09-26Fix Redefinition of OLED_TIMEOUT (#6628)Drashna Jaelre