1 files changed, 0 insertions, 106 deletions
diff --git a/lib/lufa/Projects/RelayBoard/RelayBoard.txt b/lib/lufa/Projects/RelayBoard/RelayBoard.txt
deleted file mode 100644
index 4b190dfe32..0000000000
--- a/lib/lufa/Projects/RelayBoard/RelayBoard.txt
+++ /dev/null
@@ -1,106 +0,0 @@
-/** \file
- *
- *  This file contains special DoxyGen information for the generation of the main page and other special
- *  documentation pages. It is not a project source file.
- */
-
-/** \mainpage OB's Quad-Relay outlet control using a Teensy2++
- *
- *  \section Sec_Compat Project Compatibility:
- *
- *  The following list indicates what microcontrollers are compatible with this project.
- *
- *  \li AT90USB1286
- *
- *  \section Sec_Info USB Information:
- *
- *  The following table gives a rundown of the USB utilization of this project.
- *
- * <table>
- *  <tr>
- *   <td><b>USB Mode:</b></td>
- *   <td>Device</td>
- *  </tr>
- *  <tr>
- *   <td><b>USB Class:</b></td>
- *   <td>None</td>
- *  </tr>
- *  <tr>
- *   <td><b>USB Subclass:</b></td>
- *   <td>None</td>
- *  </tr>
- *  <tr>
- *   <td><b>Relevant Standards:</b></td>
- *   <td>USB Standards</td>
- *  </tr>
- *  <tr>
- *   <td><b>Supported USB Speeds:</b></td>
- *   <td>Low Speed Mode, Full Speed Mode</td>
- *  </tr>
- * </table>
- *
- *  \section Sec_Description Project Description:
- *
- *  Firmware for a Teensy2++ AVR-based miniboard to control four relays, using the
- *  same protocol used by the commercially available Silver Shield PM power outlets
- *  ( http://sourceforge.net/projects/sispmctl ) sold for some time. Because this
- *  project mimics the original device, it can be controlled using the "sismpctl"
- *  package included in many Linux distributions - including router-orientated
- *  versions such as OpenWRT - to control the board's relays.
- *
- *  Relays 1 to 4 are respectively wired to pins C4, C5, C6 and C7 of the Teensy++ V2,
- *  which are the PORTC bits 4 to 7 of the AT90USB1286. The relays MUST be wired through
- *  a transistor, and a diode must be added in antiparallel on the relay's coil pins to
- *  protect the transistor from back EMF generated from the relay when the coil is turned off.
- *  The transistor base pin is wired to the Teensy data port through a 10K resistor. A
- *  LED may be also be added as a relay status indicator on each channel.
- *
- *  The Relay coil will be driven by the transistor, but the power will come from
- *  the 5V from the PC's USB port: Be careful in choosing the relay to avoid overloading
- *  the PC, as the maximum current used MUST remains under ~450mA @ 5V.
- *
- *  The author's tested relays are 2 Finder 32.21.7.005.2000, coil il 125ohm, which can
- *  handle 5A @ 250VAC. Be careful to use proper isolation if high voltages are manipulated.
- *  The author used Hotglue to isolate all parts of the PCB in contact with high voltage.
- *
- *  See <a>http://www.pjrc.com/teensy/</a> for the Teensy2++ website.
- *
- *  <table>
- *   <tr>
- *    <td><b>Signal:</b></td>
- *    <td><b>AVR Port:</b></td>
- *   </tr>
- *   <tr>
- *    <td>Relay 1</td>
- *    <td>PORTC, Pin 4</td>
- *   </tr>
- *   <tr>
- *    <td>Relay 2</td>
- *    <td>PORTC, Pin 5</td>
- *   </tr>
- *   <tr>
- *    <td>Relay 3</td>
- *    <td>PORTC, Pin 6</td>
- *   </tr>
- *   <tr>
- *    <td>Relay 4</td>
- *    <td>PORTC, Pin 7</td>
- *   </tr>
- *   <tr>
- *    <td>Teensy2++ Yellow Led</td>
- *    <td>PORTD, pin 6</td>
- *   </tr>
- *  </table>
- *
- *  \section Sec_Options Project Options
- *
- *  The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
- *
- *  <table>
- *   <tr>
- *    <td>
- *     None
- *    </td>
- *   </tr>
- *  </table>
- */