diff options
Diffstat (limited to 'keyboards')
| -rw-r--r-- | keyboards/crkbd/rev1/serial_config.h | 12 | ||||
| -rw-r--r-- | keyboards/crkbd/rev1/split_scomm.c | 49 | ||||
| -rw-r--r-- | keyboards/crkbd/rev1/split_scomm.h | 5 | ||||
| -rw-r--r-- | keyboards/crkbd/rev1/split_util.h | 5 | ||||
| -rw-r--r-- | keyboards/crkbd/serial.c | 284 | ||||
| -rw-r--r-- | keyboards/crkbd/serial.h | 27 |
6 files changed, 277 insertions, 105 deletions
diff --git a/keyboards/crkbd/rev1/serial_config.h b/keyboards/crkbd/rev1/serial_config.h index 671ed821d2..4fab8e8ddf 100644 --- a/keyboards/crkbd/rev1/serial_config.h +++ b/keyboards/crkbd/rev1/serial_config.h @@ -1,10 +1,4 @@ -#pragma once - -/* Soft Serial defines */ -#define SERIAL_PIN_DDR DDRD -#define SERIAL_PIN_PORT PORTD -#define SERIAL_PIN_INPUT PIND -#define SERIAL_PIN_MASK _BV(PD2) -#define SERIAL_PIN_INTERRUPT INT2_vect - +#ifndef SOFT_SERIAL_PIN +#define SOFT_SERIAL_PIN D2 #define SERIAL_USE_MULTI_TRANSACTION +#endif diff --git a/keyboards/crkbd/rev1/split_scomm.c b/keyboards/crkbd/rev1/split_scomm.c index 9719eb22ea..ada7867960 100644 --- a/keyboards/crkbd/rev1/split_scomm.c +++ b/keyboards/crkbd/rev1/split_scomm.c @@ -7,8 +7,8 @@ #include <stddef.h> #include <split_scomm.h> #include "serial.h" -#ifdef SERIAL_DEBUG_MODE -#include <avr/io.h> +#ifdef CONSOLE_ENABLE + #include <print.h> #endif uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0}; @@ -17,6 +17,7 @@ uint8_t volatile status_com = 0; uint8_t volatile status1 = 0; uint8_t slave_buffer_change_count = 0; uint8_t s_change_old = 0xff; +uint8_t s_change_new = 0xff; SSTD_t transactions[] = { #define GET_SLAVE_STATUS 0 @@ -41,12 +42,12 @@ SSTD_t transactions[] = { void serial_master_init(void) { - soft_serial_initiator_init(transactions); + soft_serial_initiator_init(transactions, TID_LIMIT(transactions)); } void serial_slave_init(void) { - soft_serial_target_init(transactions); + soft_serial_target_init(transactions, TID_LIMIT(transactions)); } // 0 => no error @@ -54,19 +55,37 @@ void serial_slave_init(void) // 2 => checksum error int serial_update_buffers(int master_update) { - int status; + int status, smatstatus; static int need_retry = 0; - if( s_change_old != slave_buffer_change_count ) { - status = soft_serial_transaction(GET_SLAVE_BUFFER); - if( status == TRANSACTION_END ) - s_change_old = slave_buffer_change_count; + + if( s_change_old != s_change_new ) { + smatstatus = soft_serial_transaction(GET_SLAVE_BUFFER); + if( smatstatus == TRANSACTION_END ) { + s_change_old = s_change_new; +#ifdef CONSOLE_ENABLE + uprintf("slave matrix = %b %b %b %b %b\n", + serial_slave_buffer[0], serial_slave_buffer[1], + serial_slave_buffer[2], serial_slave_buffer[3], + serial_slave_buffer[4] ); +#endif + } + } else { + // serial_slave_buffer dosen't change + smatstatus = TRANSACTION_END; // dummy status + } + + if( !master_update && !need_retry) { + status = soft_serial_transaction(GET_SLAVE_STATUS); + } else { + status = soft_serial_transaction(PUT_MASTER_GET_SLAVE_STATUS); + } + if( status == TRANSACTION_END ) { + s_change_new = slave_buffer_change_count; + need_retry = 0; + } else { + need_retry = 1; } - if( !master_update && !need_retry) - status = soft_serial_transaction(GET_SLAVE_STATUS); - else - status = soft_serial_transaction(PUT_MASTER_GET_SLAVE_STATUS); - need_retry = ( status == TRANSACTION_END ) ? 0 : 1; - return status; + return smatstatus; } #endif // SERIAL_USE_MULTI_TRANSACTION diff --git a/keyboards/crkbd/rev1/split_scomm.h b/keyboards/crkbd/rev1/split_scomm.h index 16887eb74f..873d8939d8 100644 --- a/keyboards/crkbd/rev1/split_scomm.h +++ b/keyboards/crkbd/rev1/split_scomm.h @@ -1,4 +1,5 @@ -#pragma once +#ifndef SPLIT_COMM_H +#define SPLIT_COMM_H #ifndef SERIAL_USE_MULTI_TRANSACTION /* --- USE Simple API (OLD API, compatible with let's split serial.c) --- */ @@ -19,3 +20,5 @@ void serial_slave_init(void); int serial_update_buffers(int master_changed); #endif + +#endif /* SPLIT_COMM_H */ diff --git a/keyboards/crkbd/rev1/split_util.h b/keyboards/crkbd/rev1/split_util.h index f593047560..687ca19bd3 100644 --- a/keyboards/crkbd/rev1/split_util.h +++ b/keyboards/crkbd/rev1/split_util.h @@ -1,4 +1,5 @@ -#pragma once +#ifndef SPLIT_KEYBOARD_UTIL_H +#define SPLIT_KEYBOARD_UTIL_H #include <stdbool.h> #include "eeconfig.h" @@ -14,3 +15,5 @@ void split_keyboard_setup(void); bool has_usb(void); void matrix_master_OLED_init (void); + +#endif diff --git a/keyboards/crkbd/serial.c b/keyboards/crkbd/serial.c index 11ceff0b37..325c29a3f7 100644 --- a/keyboards/crkbd/serial.c +++ b/keyboards/crkbd/serial.c @@ -1,5 +1,10 @@ /* * WARNING: be careful changing this code, it is very timing dependent + * + * 2018-10-28 checked + * avr-gcc 4.9.2 + * avr-gcc 5.4.0 + * avr-gcc 7.3.0 */ #ifndef F_CPU @@ -14,8 +19,58 @@ #include "serial.h" //#include <pro_micro.h> -#ifdef USE_SERIAL +#ifdef SOFT_SERIAL_PIN +#ifdef __AVR_ATmega32U4__ + // if using ATmega32U4 I2C, can not use PD0 and PD1 in soft serial. + #ifdef USE_I2C + #if SOFT_SERIAL_PIN == D0 || SOFT_SERIAL_PIN == D1 + #error Using ATmega32U4 I2C, so can not use PD0, PD1 + #endif + #endif + + #if SOFT_SERIAL_PIN >= D0 && SOFT_SERIAL_PIN <= D3 + #define SERIAL_PIN_DDR DDRD + #define SERIAL_PIN_PORT PORTD + #define SERIAL_PIN_INPUT PIND + #if SOFT_SERIAL_PIN == D0 + #define SERIAL_PIN_MASK _BV(PD0) + #define EIMSK_BIT _BV(INT0) + #define EICRx_BIT (~(_BV(ISC00) | _BV(ISC01))) + #define SERIAL_PIN_INTERRUPT INT0_vect + #elif SOFT_SERIAL_PIN == D1 + #define SERIAL_PIN_MASK _BV(PD1) + #define EIMSK_BIT _BV(INT1) + #define EICRx_BIT (~(_BV(ISC10) | _BV(ISC11))) + #define SERIAL_PIN_INTERRUPT INT1_vect + #elif SOFT_SERIAL_PIN == D2 + #define SERIAL_PIN_MASK _BV(PD2) + #define EIMSK_BIT _BV(INT2) + #define EICRx_BIT (~(_BV(ISC20) | _BV(ISC21))) + #define SERIAL_PIN_INTERRUPT INT2_vect + #elif SOFT_SERIAL_PIN == D3 + #define SERIAL_PIN_MASK _BV(PD3) + #define EIMSK_BIT _BV(INT3) + #define EICRx_BIT (~(_BV(ISC30) | _BV(ISC31))) + #define SERIAL_PIN_INTERRUPT INT3_vect + #endif + #elif SOFT_SERIAL_PIN == E6 + #define SERIAL_PIN_DDR DDRE + #define SERIAL_PIN_PORT PORTE + #define SERIAL_PIN_INPUT PINE + #define SERIAL_PIN_MASK _BV(PE6) + #define EIMSK_BIT _BV(INT6) + #define EICRx_BIT (~(_BV(ISC60) | _BV(ISC61))) + #define SERIAL_PIN_INTERRUPT INT6_vect + #else + #error invalid SOFT_SERIAL_PIN value + #endif + +#else + #error serial.c now support ATmega32U4 only +#endif + +//////////////// for backward compatibility //////////////////////////////// #ifndef SERIAL_USE_MULTI_TRANSACTION /* --- USE Simple API (OLD API, compatible with let's split serial.c) */ #if SERIAL_SLAVE_BUFFER_LENGTH > 0 @@ -42,56 +97,118 @@ SSTD_t transactions[] = { }; void serial_master_init(void) -{ soft_serial_initiator_init(transactions); } +{ soft_serial_initiator_init(transactions, TID_LIMIT(transactions)); } void serial_slave_init(void) -{ soft_serial_target_init(transactions); } +{ soft_serial_target_init(transactions, TID_LIMIT(transactions)); } // 0 => no error // 1 => slave did not respond // 2 => checksum error int serial_update_buffers() -{ return soft_serial_transaction(); } +{ + int result; + result = soft_serial_transaction(); + return result; +} -#endif // Simple API (OLD API, compatible with let's split serial.c) +#endif // end of Simple API (OLD API, compatible with let's split serial.c) +//////////////////////////////////////////////////////////////////////////// #define ALWAYS_INLINE __attribute__((always_inline)) #define NO_INLINE __attribute__((noinline)) #define _delay_sub_us(x) __builtin_avr_delay_cycles(x) -// Serial pulse period in microseconds. -#define TID_SEND_ADJUST 14 +// parity check +#define ODD_PARITY 1 +#define EVEN_PARITY 0 +#define PARITY EVEN_PARITY + +#ifdef SERIAL_DELAY + // custom setup in config.h + // #define TID_SEND_ADJUST 2 + // #define SERIAL_DELAY 6 // micro sec + // #define READ_WRITE_START_ADJUST 30 // cycles + // #define READ_WRITE_WIDTH_ADJUST 8 // cycles +#else +// ============ Standard setups ============ + +#ifndef SELECT_SOFT_SERIAL_SPEED +#define SELECT_SOFT_SERIAL_SPEED 1 +// 0: about 189kbps +// 1: about 137kbps (default) +// 2: about 75kbps +// 3: about 39kbps +// 4: about 26kbps +// 5: about 20kbps +#endif -#define SELECT_SERIAL_SPEED 1 -#if SELECT_SERIAL_SPEED == 0 +#if __GNUC__ < 6 + #define TID_SEND_ADJUST 14 +#else + #define TID_SEND_ADJUST 2 +#endif + +#if SELECT_SOFT_SERIAL_SPEED == 0 // Very High speed #define SERIAL_DELAY 4 // micro sec - #define READ_WRITE_START_ADJUST 33 // cycles - #define READ_WRITE_WIDTH_ADJUST 3 // cycles -#elif SELECT_SERIAL_SPEED == 1 + #if __GNUC__ < 6 + #define READ_WRITE_START_ADJUST 33 // cycles + #define READ_WRITE_WIDTH_ADJUST 3 // cycles + #else + #define READ_WRITE_START_ADJUST 34 // cycles + #define READ_WRITE_WIDTH_ADJUST 7 // cycles + #endif +#elif SELECT_SOFT_SERIAL_SPEED == 1 // High speed #define SERIAL_DELAY 6 // micro sec - #define READ_WRITE_START_ADJUST 30 // cycles - #define READ_WRITE_WIDTH_ADJUST 3 // cycles -#elif SELECT_SERIAL_SPEED == 2 + #if __GNUC__ < 6 + #define READ_WRITE_START_ADJUST 30 // cycles + #define READ_WRITE_WIDTH_ADJUST 3 // cycles + #else + #define READ_WRITE_START_ADJUST 33 // cycles + #define READ_WRITE_WIDTH_ADJUST 7 // cycles + #endif +#elif SELECT_SOFT_SERIAL_SPEED == 2 // Middle speed #define SERIAL_DELAY 12 // micro sec #define READ_WRITE_START_ADJUST 30 // cycles - #define READ_WRITE_WIDTH_ADJUST 3 // cycles -#elif SELECT_SERIAL_SPEED == 3 + #if __GNUC__ < 6 + #define READ_WRITE_WIDTH_ADJUST 3 // cycles + #else + #define READ_WRITE_WIDTH_ADJUST 7 // cycles + #endif +#elif SELECT_SOFT_SERIAL_SPEED == 3 // Low speed #define SERIAL_DELAY 24 // micro sec #define READ_WRITE_START_ADJUST 30 // cycles - #define READ_WRITE_WIDTH_ADJUST 3 // cycles -#elif SELECT_SERIAL_SPEED == 4 + #if __GNUC__ < 6 + #define READ_WRITE_WIDTH_ADJUST 3 // cycles + #else + #define READ_WRITE_WIDTH_ADJUST 7 // cycles + #endif +#elif SELECT_SOFT_SERIAL_SPEED == 4 // Very Low speed - #define SERIAL_DELAY 50 // micro sec + #define SERIAL_DELAY 36 // micro sec + #define READ_WRITE_START_ADJUST 30 // cycles + #if __GNUC__ < 6 + #define READ_WRITE_WIDTH_ADJUST 3 // cycles + #else + #define READ_WRITE_WIDTH_ADJUST 7 // cycles + #endif +#elif SELECT_SOFT_SERIAL_SPEED == 5 + // Ultra Low speed + #define SERIAL_DELAY 48 // micro sec #define READ_WRITE_START_ADJUST 30 // cycles - #define READ_WRITE_WIDTH_ADJUST 3 // cycles + #if __GNUC__ < 6 + #define READ_WRITE_WIDTH_ADJUST 3 // cycles + #else + #define READ_WRITE_WIDTH_ADJUST 7 // cycles + #endif #else -#error Illegal Serial Speed -#endif - +#error invalid SELECT_SOFT_SERIAL_SPEED value +#endif /* SELECT_SOFT_SERIAL_SPEED */ +#endif /* SERIAL_DELAY */ #define SERIAL_DELAY_HALF1 (SERIAL_DELAY/2) #define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY/2) @@ -105,17 +222,21 @@ int serial_update_buffers() #endif static SSTD_t *Transaction_table = NULL; +static uint8_t Transaction_table_size = 0; +inline static void serial_delay(void) ALWAYS_INLINE; inline static void serial_delay(void) { _delay_us(SERIAL_DELAY); } +inline static void serial_delay_half1(void) ALWAYS_INLINE; inline static void serial_delay_half1(void) { _delay_us(SERIAL_DELAY_HALF1); } +inline static void serial_delay_half2(void) ALWAYS_INLINE; inline static void serial_delay_half2(void) { _delay_us(SERIAL_DELAY_HALF2); @@ -135,6 +256,7 @@ void serial_input_with_pullup(void) { SERIAL_PIN_PORT |= SERIAL_PIN_MASK; } +inline static uint8_t serial_read_pin(void) ALWAYS_INLINE; inline static uint8_t serial_read_pin(void) { return !!(SERIAL_PIN_INPUT & SERIAL_PIN_MASK); @@ -152,30 +274,28 @@ void serial_high(void) { SERIAL_PIN_PORT |= SERIAL_PIN_MASK; } -void soft_serial_initiator_init(SSTD_t *sstd_table) +void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size) { Transaction_table = sstd_table; + Transaction_table_size = (uint8_t)sstd_table_size; serial_output(); serial_high(); } -void soft_serial_target_init(SSTD_t *sstd_table) +void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size) { Transaction_table = sstd_table; + Transaction_table_size = (uint8_t)sstd_table_size; serial_input_with_pullup(); -#if SERIAL_PIN_MASK == _BV(PD0) - // Enable INT0 - EIMSK |= _BV(INT0); - // Trigger on falling edge of INT0 - EICRA &= ~(_BV(ISC00) | _BV(ISC01)); -#elif SERIAL_PIN_MASK == _BV(PD2) - // Enable INT2 - EIMSK |= _BV(INT2); - // Trigger on falling edge of INT2 - EICRA &= ~(_BV(ISC20) | _BV(ISC21)); + // Enable INT0-INT3,INT6 + EIMSK |= EIMSK_BIT; +#if SERIAL_PIN_MASK == _BV(PE6) + // Trigger on falling edge of INT6 + EICRB &= EICRx_BIT; #else - #error unknown SERIAL_PIN_MASK value + // Trigger on falling edge of INT0-INT3 + EICRA &= EICRx_BIT; #endif } @@ -191,7 +311,7 @@ void sync_recv(void) { } // Used by the reciver to send a synchronization signal to the sender. -static void sync_send(void)NO_INLINE; +static void sync_send(void) NO_INLINE; static void sync_send(void) { serial_low(); @@ -205,12 +325,12 @@ static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) { uint8_t byte, i, p, pb; _delay_sub_us(READ_WRITE_START_ADJUST); - for( i = 0, byte = 0, p = 0; i < bit; i++ ) { + for( i = 0, byte = 0, p = PARITY; i < bit; i++ ) { serial_delay_half1(); // read the middle of pulses if( serial_read_pin() ) { - byte = (byte << 1) | 1; p ^= 1; + byte = (byte << 1) | 1; p ^= 1; } else { - byte = (byte << 1) | 0; p ^= 0; + byte = (byte << 1) | 0; p ^= 0; } _delay_sub_us(READ_WRITE_WIDTH_ADJUST); serial_delay_half2(); @@ -230,13 +350,13 @@ static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) { void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE; void serial_write_chunk(uint8_t data, uint8_t bit) { uint8_t b, p; - for( p = 0, b = 1<<(bit-1); b ; b >>= 1) { - if(data & b) { - serial_high(); p ^= 1; - } else { - serial_low(); p ^= 0; - } - serial_delay(); + for( p = PARITY, b = 1<<(bit-1); b ; b >>= 1) { + if(data & b) { + serial_high(); p ^= 1; + } else { + serial_low(); p ^= 0; + } + serial_delay(); } /* send parity bit */ if(p & 1) { serial_high(); } @@ -288,6 +408,13 @@ void change_reciver2sender(void) { serial_delay_half1(); //4 } +static inline uint8_t nibble_bits_count(uint8_t bits) +{ + bits = (bits & 0x5) + (bits >> 1 & 0x5); + bits = (bits & 0x3) + (bits >> 2 & 0x3); + return bits; +} + // interrupt handle to be used by the target device ISR(SERIAL_PIN_INTERRUPT) { @@ -297,12 +424,15 @@ ISR(SERIAL_PIN_INTERRUPT) { SSTD_t *trans = Transaction_table; #else // recive transaction table index - uint8_t tid; + uint8_t tid, bits; uint8_t pecount = 0; sync_recv(); - tid = serial_read_chunk(&pecount,4); - if(pecount> 0) + bits = serial_read_chunk(&pecount,7); + tid = bits>>3; + bits = (bits&7) != nibble_bits_count(tid); + if( bits || pecount> 0 || tid > Transaction_table_size ) { return; + } serial_delay_half1(); serial_high(); // response step1 low->high @@ -315,17 +445,17 @@ ISR(SERIAL_PIN_INTERRUPT) { // target send phase if( trans->target2initiator_buffer_size > 0 ) serial_send_packet((uint8_t *)trans->target2initiator_buffer, - trans->target2initiator_buffer_size); + trans->target2initiator_buffer_size); // target switch to input change_sender2reciver(); // target recive phase if( trans->initiator2target_buffer_size > 0 ) { if (serial_recive_packet((uint8_t *)trans->initiator2target_buffer, - trans->initiator2target_buffer_size) ) { - *trans->status = TRANSACTION_ACCEPTED; + trans->initiator2target_buffer_size) ) { + *trans->status = TRANSACTION_ACCEPTED; } else { - *trans->status = TRANSACTION_DATA_ERROR; + *trans->status = TRANSACTION_DATA_ERROR; } } else { *trans->status = TRANSACTION_ACCEPTED; @@ -349,6 +479,8 @@ int soft_serial_transaction(void) { SSTD_t *trans = Transaction_table; #else int soft_serial_transaction(int sstd_index) { + if( sstd_index > Transaction_table_size ) + return TRANSACTION_TYPE_ERROR; SSTD_t *trans = &Transaction_table[sstd_index]; #endif cli(); @@ -375,9 +507,10 @@ int soft_serial_transaction(int sstd_index) { #else // send transaction table index + int tid = (sstd_index<<3) | (7 & nibble_bits_count(sstd_index)); sync_send(); _delay_sub_us(TID_SEND_ADJUST); - serial_write_chunk(sstd_index, 4); + serial_write_chunk(tid, 7); serial_delay_half1(); // wait for the target response (step1 low->high) @@ -389,12 +522,12 @@ int soft_serial_transaction(int sstd_index) { // check if the target is present (step2 high->low) for( int i = 0; serial_read_pin(); i++ ) { if (i > SLAVE_INT_ACK_WIDTH + 1) { - // slave failed to pull the line low, assume not present - serial_output(); - serial_high(); - *trans->status = TRANSACTION_NO_RESPONSE; - sei(); - return TRANSACTION_NO_RESPONSE; + // slave failed to pull the line low, assume not present + serial_output(); + serial_high(); + *trans->status = TRANSACTION_NO_RESPONSE; + sei(); + return TRANSACTION_NO_RESPONSE; } _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT); } @@ -404,12 +537,12 @@ int soft_serial_transaction(int sstd_index) { // if the target is present syncronize with it if( trans->target2initiator_buffer_size > 0 ) { if (!serial_recive_packet((uint8_t *)trans->target2initiator_buffer, - trans->target2initiator_buffer_size) ) { - serial_output(); - serial_high(); - *trans->status = TRANSACTION_DATA_ERROR; - sei(); - return TRANSACTION_DATA_ERROR; + trans->target2initiator_buffer_size) ) { + serial_output(); + serial_high(); + *trans->status = TRANSACTION_DATA_ERROR; + sei(); + return TRANSACTION_DATA_ERROR; } } @@ -419,7 +552,7 @@ int soft_serial_transaction(int sstd_index) { // initiator send phase if( trans->initiator2target_buffer_size > 0 ) { serial_send_packet((uint8_t *)trans->initiator2target_buffer, - trans->initiator2target_buffer_size); + trans->initiator2target_buffer_size); } // always, release the line when not in use @@ -442,3 +575,16 @@ int soft_serial_get_and_clean_status(int sstd_index) { #endif #endif + +// Helix serial.c history +// 2018-1-29 fork from let's split and add PD2, modify sync_recv() (#2308, bceffdefc) +// 2018-6-28 bug fix master to slave comm and speed up (#3255, 1038bbef4) +// (adjusted with avr-gcc 4.9.2) +// 2018-7-13 remove USE_SERIAL_PD2 macro (#3374, f30d6dd78) +// (adjusted with avr-gcc 4.9.2) +// 2018-8-11 add support multi-type transaction (#3608, feb5e4aae) +// (adjusted with avr-gcc 4.9.2) +// 2018-10-21 fix serial and RGB animation conflict (#4191, 4665e4fff) +// (adjusted with avr-gcc 7.3.0) +// 2018-10-28 re-adjust compiler depend value of delay (#4269, 8517f8a66) +// (adjusted with avr-gcc 5.4.0, 7.3.0) diff --git a/keyboards/crkbd/serial.h b/keyboards/crkbd/serial.h index 76c6aaa043..7e0c0847a4 100644 --- a/keyboards/crkbd/serial.h +++ b/keyboards/crkbd/serial.h @@ -1,16 +1,19 @@ -#pragma once +#ifndef SOFT_SERIAL_H +#define SOFT_SERIAL_H #include <stdbool.h> // ///////////////////////////////////////////////////////////////// -// Need Soft Serial defines in serial_config.h +// Need Soft Serial defines in config.h // ///////////////////////////////////////////////////////////////// // ex. -// #define SERIAL_PIN_DDR DDRD -// #define SERIAL_PIN_PORT PORTD -// #define SERIAL_PIN_INPUT PIND -// #define SERIAL_PIN_MASK _BV(PD?) ?=0,2 -// #define SERIAL_PIN_INTERRUPT INT?_vect ?=0,2 +// #define SOFT_SERIAL_PIN ?? // ?? = D0,D1,D2,D3,E6 +// OPTIONAL: #define SELECT_SOFT_SERIAL_SPEED ? // ? = 1,2,3,4,5 +// // 1: about 137kbps (default) +// // 2: about 75kbps +// // 3: about 39kbps +// // 4: about 26kbps +// // 5: about 20kbps // // //// USE Simple API (OLD API, compatible with let's split serial.c) // ex. @@ -46,16 +49,18 @@ typedef struct _SSTD_t { uint8_t target2initiator_buffer_size; uint8_t *target2initiator_buffer; } SSTD_t; +#define TID_LIMIT( table ) (sizeof(table) / sizeof(SSTD_t)) // initiator is transaction start side -void soft_serial_initiator_init(SSTD_t *sstd_table); +void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size); // target is interrupt accept side -void soft_serial_target_init(SSTD_t *sstd_table); +void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size); // initiator resullt #define TRANSACTION_END 0 #define TRANSACTION_NO_RESPONSE 0x1 #define TRANSACTION_DATA_ERROR 0x2 +#define TRANSACTION_TYPE_ERROR 0x4 #ifndef SERIAL_USE_MULTI_TRANSACTION int soft_serial_transaction(void); #else @@ -71,7 +76,9 @@ int soft_serial_transaction(int sstd_index); // target: // TRANSACTION_DATA_ERROR // or TRANSACTION_ACCEPTED -#define TRANSACTION_ACCEPTED 0x4 +#define TRANSACTION_ACCEPTED 0x8 #ifdef SERIAL_USE_MULTI_TRANSACTION int soft_serial_get_and_clean_status(int sstd_index); #endif + +#endif /* SOFT_SERIAL_H */ |