diff options
Diffstat (limited to 'keyboards/tkc/candybar')
22 files changed, 2039 insertions, 0 deletions
diff --git a/keyboards/tkc/candybar/bootloader_defs.h b/keyboards/tkc/candybar/bootloader_defs.h new file mode 100644 index 0000000000..43eb7b2f62 --- /dev/null +++ b/keyboards/tkc/candybar/bootloader_defs.h @@ -0,0 +1,7 @@ +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here: + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + * This also requires a patch to chibios: + * <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch + */ +#define STM32_BOOTLOADER_ADDRESS 0x1FFFC800 diff --git a/keyboards/tkc/candybar/chconf.h b/keyboards/tkc/candybar/chconf.h new file mode 100644 index 0000000000..03f63da36a --- /dev/null +++ b/keyboards/tkc/candybar/chconf.h @@ -0,0 +1,714 @@ +/* + ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file rt/templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ +#define _CHIBIOS_RT_CONF_VER_6_0_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#if !defined(CH_CFG_ST_RESOLUTION) +#define CH_CFG_ST_RESOLUTION 32 +#endif + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#if !defined(CH_CFG_ST_FREQUENCY) +#define CH_CFG_ST_FREQUENCY 10000 +#endif + +/** + * @brief Time intervals data size. + * @note Allowed values are 16, 32 or 64 bits. + */ +#if !defined(CH_CFG_INTERVALS_SIZE) +#define CH_CFG_INTERVALS_SIZE 32 +#endif + +/** + * @brief Time types data size. + * @note Allowed values are 16 or 32 bits. + */ +#if !defined(CH_CFG_TIME_TYPES_SIZE) +#define CH_CFG_TIME_TYPES_SIZE 32 +#endif + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#if !defined(CH_CFG_ST_TIMEDELTA) +#define CH_CFG_ST_TIMEDELTA 2 +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#if !defined(CH_CFG_TIME_QUANTUM) +#define CH_CFG_TIME_QUANTUM 0 +#endif + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#if !defined(CH_CFG_MEMCORE_SIZE) +#define CH_CFG_MEMCORE_SIZE 0 +#endif + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#if !defined(CH_CFG_NO_IDLE_THREAD) +#define CH_CFG_NO_IDLE_THREAD FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_OPTIMIZE_SPEED) +#define CH_CFG_OPTIMIZE_SPEED FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_TM) +#define CH_CFG_USE_TM FALSE +#endif + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_REGISTRY) +#define CH_CFG_USE_REGISTRY TRUE +#endif + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_WAITEXIT) +#define CH_CFG_USE_WAITEXIT TRUE +#endif + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_SEMAPHORES) +#define CH_CFG_USE_SEMAPHORES TRUE +#endif + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#if !defined(CH_CFG_USE_SEMAPHORES_PRIORITY) +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE +#endif + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MUTEXES) +#define CH_CFG_USE_MUTEXES TRUE +#endif + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#if !defined(CH_CFG_USE_MUTEXES_RECURSIVE) +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE +#endif + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#if !defined(CH_CFG_USE_CONDVARS) +#define CH_CFG_USE_CONDVARS TRUE +#endif + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#if !defined(CH_CFG_USE_CONDVARS_TIMEOUT) +#define CH_CFG_USE_CONDVARS_TIMEOUT FALSE +#endif + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_EVENTS) +#define CH_CFG_USE_EVENTS TRUE +#endif + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#if !defined(CH_CFG_USE_EVENTS_TIMEOUT) +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE +#endif + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MESSAGES) +#define CH_CFG_USE_MESSAGES TRUE +#endif + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#if !defined(CH_CFG_USE_MESSAGES_PRIORITY) +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE +#endif + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#if !defined(CH_CFG_USE_MAILBOXES) +#define CH_CFG_USE_MAILBOXES TRUE +#endif + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MEMCORE) +#define CH_CFG_USE_MEMCORE TRUE +#endif + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#if !defined(CH_CFG_USE_HEAP) +#define CH_CFG_USE_HEAP FALSE +#endif + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MEMPOOLS) +#define CH_CFG_USE_MEMPOOLS FALSE +#endif + +/** + * @brief Objects FIFOs APIs. + * @details If enabled then the objects FIFOs APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_OBJ_FIFOS) +#define CH_CFG_USE_OBJ_FIFOS FALSE +#endif + +/** + * @brief Pipes APIs. + * @details If enabled then the pipes APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_PIPES) +#define CH_CFG_USE_PIPES FALSE +#endif + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#if !defined(CH_CFG_USE_DYNAMIC) +#define CH_CFG_USE_DYNAMIC FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Objects factory options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Objects Factory APIs. + * @details If enabled then the objects factory APIs are included in the + * kernel. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_CFG_USE_FACTORY) +#define CH_CFG_USE_FACTORY FALSE +#endif + +/** + * @brief Maximum length for object names. + * @details If the specified length is zero then the name is stored by + * pointer but this could have unintended side effects. + */ +#if !defined(CH_CFG_FACTORY_MAX_NAMES_LENGTH) +#define CH_CFG_FACTORY_MAX_NAMES_LENGTH 8 +#endif + +/** + * @brief Enables the registry of generic objects. + */ +#if !defined(CH_CFG_FACTORY_OBJECTS_REGISTRY) +#define CH_CFG_FACTORY_OBJECTS_REGISTRY FALSE +#endif + +/** + * @brief Enables factory for generic buffers. + */ +#if !defined(CH_CFG_FACTORY_GENERIC_BUFFERS) +#define CH_CFG_FACTORY_GENERIC_BUFFERS FALSE +#endif + +/** + * @brief Enables factory for semaphores. + */ +#if !defined(CH_CFG_FACTORY_SEMAPHORES) +#define CH_CFG_FACTORY_SEMAPHORES FALSE +#endif + +/** + * @brief Enables factory for mailboxes. + */ +#if !defined(CH_CFG_FACTORY_MAILBOXES) +#define CH_CFG_FACTORY_MAILBOXES FALSE +#endif + +/** + * @brief Enables factory for objects FIFOs. + */ +#if !defined(CH_CFG_FACTORY_OBJ_FIFOS) +#define CH_CFG_FACTORY_OBJ_FIFOS FALSE +#endif + +/** + * @brief Enables factory for Pipes. + */ +#if !defined(CH_CFG_FACTORY_PIPES) || defined(__DOXYGEN__) +#define CH_CFG_FACTORY_PIPES FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_STATISTICS) +#define CH_DBG_STATISTICS FALSE +#endif + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_SYSTEM_STATE_CHECK) +#define CH_DBG_SYSTEM_STATE_CHECK FALSE +#endif + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_ENABLE_CHECKS) +#define CH_DBG_ENABLE_CHECKS FALSE +#endif + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_ENABLE_ASSERTS) +#define CH_DBG_ENABLE_ASSERTS FALSE +#endif + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#if !defined(CH_DBG_TRACE_MASK) +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED +#endif + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#if !defined(CH_DBG_TRACE_BUFFER_SIZE) +#define CH_DBG_TRACE_BUFFER_SIZE 128 +#endif + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#if !defined(CH_DBG_ENABLE_STACK_CHECK) +#define CH_DBG_ENABLE_STACK_CHECK FALSE +#endif + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_FILL_THREADS) +#define CH_DBG_FILL_THREADS FALSE +#endif + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#if !defined(CH_DBG_THREADS_PROFILING) +#define CH_DBG_THREADS_PROFILING FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System structure extension. + * @details User fields added to the end of the @p ch_system_t structure. + */ +#define CH_CFG_SYSTEM_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief System initialization hook. + * @details User initialization code added to the @p chSysInit() function + * just before interrupts are enabled globally. + */ +#define CH_CFG_SYSTEM_INIT_HOOK() { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p _thread_init() function. + * + * @note It is invoked from within @p _thread_init() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/tkc/candybar/halconf.h b/keyboards/tkc/candybar/halconf.h new file mode 100644 index 0000000000..16f32117d5 --- /dev/null +++ b/keyboards/tkc/candybar/halconf.h @@ -0,0 +1,525 @@ +/* + ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef HALCONF_H +#define HALCONF_H + +#define _CHIBIOS_HAL_CONF_ +#define _CHIBIOS_HAL_CONF_VER_7_0_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the cryptographic subsystem. + */ +#if !defined(HAL_USE_CRY) || defined(__DOXYGEN__) +#define HAL_USE_CRY FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT FALSE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM FALSE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB FALSE +#endif + +/** + * @brief Enables the SIO subsystem. + */ +#if !defined(HAL_USE_SIO) || defined(__DOXYGEN__) +#define HAL_USE_SIO FALSE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the TRNG subsystem. + */ +#if !defined(HAL_USE_TRNG) || defined(__DOXYGEN__) +#define HAL_USE_TRNG FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/** + * @brief Enables the WSPI subsystem. + */ +#if !defined(HAL_USE_WSPI) || defined(__DOXYGEN__) +#define HAL_USE_WSPI FALSE +#endif + +/*===========================================================================*/ +/* PAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(PAL_USE_CALLBACKS) || defined(__DOXYGEN__) +#define PAL_USE_CALLBACKS FALSE +#endif + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(PAL_USE_WAIT) || defined(__DOXYGEN__) +#define PAL_USE_WAIT FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/** + * @brief Enforces the driver to use direct callbacks rather than OSAL events. + */ +#if !defined(CAN_ENFORCE_USE_CALLBACKS) || defined(__DOXYGEN__) +#define CAN_ENFORCE_USE_CALLBACKS FALSE +#endif + +/*===========================================================================*/ +/* CRY driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the SW fall-back of the cryptographic driver. + * @details When enabled, this option, activates a fall-back software + * implementation for algorithms not supported by the underlying + * hardware. + * @note Fall-back implementations may not be present for all algorithms. + */ +#if !defined(HAL_CRY_USE_FALLBACK) || defined(__DOXYGEN__) +#define HAL_CRY_USE_FALLBACK FALSE +#endif + +/** + * @brief Makes the driver forcibly use the fall-back implementations. + */ +#if !defined(HAL_CRY_ENFORCE_FALLBACK) || defined(__DOXYGEN__) +#define HAL_CRY_ENFORCE_FALLBACK FALSE +#endif + +/*===========================================================================*/ +/* DAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(DAC_USE_WAIT) || defined(__DOXYGEN__) +#define DAC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p dacAcquireBus() and @p dacReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(DAC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define DAC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the zero-copy API. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/** + * @brief OCR initialization constant for V20 cards. + */ +#if !defined(SDC_INIT_OCR_V20) || defined(__DOXYGEN__) +#define SDC_INIT_OCR_V20 0x50FF8000U +#endif + +/** + * @brief OCR initialization constant for non-V20 cards. + */ +#if !defined(SDC_INIT_OCR) || defined(__DOXYGEN__) +#define SDC_INIT_OCR 0x80100000U +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 16 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 256 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/** + * @brief Serial over USB number of buffers. + * @note The default is 2 buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_NUMBER 2 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables circular transfers APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_CIRCULAR) || defined(__DOXYGEN__) +#define SPI_USE_CIRCULAR FALSE +#endif + + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/** + * @brief Handling method for SPI CS line. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_SELECT_MODE) || defined(__DOXYGEN__) +#define SPI_SELECT_MODE SPI_SELECT_MODE_PAD +#endif + +/*===========================================================================*/ +/* UART driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__) +#define UART_USE_WAIT FALSE +#endif + +/** + * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define UART_USE_MUTUAL_EXCLUSION FALSE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +/*===========================================================================*/ +/* WSPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(WSPI_USE_WAIT) || defined(__DOXYGEN__) +#define WSPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p wspiAcquireBus() and @p wspiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(WSPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define WSPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +#endif /* HALCONF_H */ + +/** @} */ diff --git a/keyboards/tkc/candybar/lefty/config.h b/keyboards/tkc/candybar/lefty/config.h new file mode 100644 index 0000000000..e8a1f00815 --- /dev/null +++ b/keyboards/tkc/candybar/lefty/config.h @@ -0,0 +1,115 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x544B //TK +#define PRODUCT_ID 0x0003 +#define DEVICE_VER 0x0006 +#define MANUFACTURER The Key Company +#define PRODUCT Candybar +#define DESCRIPTION A compact staggered 40% keyboard with attached numpad + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 17 +#define DIODE_DIRECTION COL2ROW +#define MATRIX_ROW_PINS { A8, A9, A10, A13 } +#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, B0, B1, B2, B10, B11, B12, B13, B14, B15 } + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +//#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +// #define WS2812_LED_N 2 +// #define RGBLED_NUM WS2812_LED_N +// #define WS2812_TIM_N 2 +// #define WS2812_TIM_CH 2 +// #define PORT_WS2812 GPIOA +// #define PIN_WS2812 1 +// #define WS2812_DMA_STREAM STM32_DMA1_STREAM2 // DMA stream for TIMx_UP (look up in reference manual under DMA Channel selection) +//#define WS2812_DMA_CHANNEL 7 // DMA channel for TIMx_UP +//#define WS2812_EXTERNAL_PULLUP diff --git a/keyboards/tkc/candybar/lefty/info.json b/keyboards/tkc/candybar/lefty/info.json new file mode 100644 index 0000000000..1ef3dcd54a --- /dev/null +++ b/keyboards/tkc/candybar/lefty/info.json @@ -0,0 +1,17 @@ +{ + "keyboard_name": "TKC Candybar", + "url": "", + "maintainer": "terrymathews", + "width": 17, + "height": 4, + "layouts": { + "LAYOUT": { + "layout": [ + {"label":"7", "x":0, "y":0}, {"label":"8", "x":1, "y":0}, {"label":"9", "x":2, "y":0}, {"label":"-", "x":3, "y":0}, {"label":"Esc", "x":4, "y":0}, {"label":"Q", "x":5, "y":0}, {"label":"W", "x":6, "y":0}, {"label":"E", "x":7, "y":0}, {"label":"R", "x":8, "y":0}, {"label":"T", "x":9, "y":0}, {"label":"Y", "x":10, "y":0}, {"label":"U", "x":11, "y":0}, {"label":"I", "x":12, "y":0}, {"label":"O", "x":13, "y":0}, {"label":"P", "x":14, "y":0}, {"label":"{", "x":15, "y":0}, {"label":"}", "x":16, "y":0}, + {"label":"4", "x":0, "y":1}, {"label":"5", "x":1, "y":1}, {"label":"6", "x":2, "y":1}, {"label":"+", "x":3, "y":1}, {"label":"Tab", "x":4, "y":1, "w":1.25}, {"label":"A", "x":5.25, "y":1}, {"label":"S", "x":6.25, "y":1}, {"label":"D", "x":7.25, "y":1}, {"label":"F", "x":8.25, "y":1}, {"label":"G", "x":9.25, "y":1}, {"label":"H", "x":10.25, "y":1}, {"label":"J", "x":11.25, "y":1}, {"label":"K", "x":12.25, "y":1}, {"label":"L", "x":13.25, "y":1}, {"label":":", "x":14.25, "y":1}, {"label":"Enter", "x":15.25, "y":1, "w":1.75}, + {"label":"1", "x":0, "y":2}, {"label":"2", "x":1, "y":2}, {"label":"3", "x":2, "y":2}, {"x":3, "y":2}, {"label":"Shift", "x":4, "y":2, "w":1.75}, {"label":"Z", "x":5.75, "y":2}, {"label":"X", "x":6.75, "y":2}, {"label":"C", "x":7.75, "y":2}, {"label":"V", "x":8.75, "y":2}, {"label":"B", "x":9.75, "y":2}, {"label":"N", "x":10.75, "y":2}, {"label":"M", "x":11.75, "y":2}, {"label":"<", "x":12.75, "y":2}, {"label":">", "x":13.75, "y":2}, {"label":"\u2191", "x":14.75, "y":2}, {"label":"Shift", "x":15.75, "y":2, "w":1.25}, + {"label":"Fn", "x":0, "y":3}, {"label":"0", "x":1, "y":3}, {"label":".", "x":2, "y":3}, {"label":"Enter", "x":3, "y":3}, {"label":"Ctrl", "x":4, "y":3, "w":1.25}, {"label":"Win", "x":5.25, "y":3, "w":1.25}, {"label":"Alt", "x":6.5, "y":3, "w":1.25}, {"x":7.75, "y":3, "w":1.75}, {"x":9.5, "y":3}, {"x":10.5, "y":3, "w":2.25}, {"label":"Win", "x":12.75, "y":3, "w":1.25}, {"label":"\u2190", "x":14, "y":3}, {"label":"\u2193", "x":15, "y":3}, {"label":"\u2192", "x":16, "y":3} + ] + } + } +} diff --git a/keyboards/tkc/candybar/lefty/keymaps/default/keymap.c b/keyboards/tkc/candybar/lefty/keymaps/default/keymap.c new file mode 100644 index 0000000000..153fd99c50 --- /dev/null +++ b/keyboards/tkc/candybar/lefty/keymaps/default/keymap.c @@ -0,0 +1,38 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include QMK_KEYBOARD_H + +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: Base Layer (Default Layer) + */ +[_BL] = LAYOUT( + KC_P7 , KC_P8, KC_P9 , KC_PAST, KC_ESC , KC_Q , KC_W , KC_E, KC_R , KC_T , KC_Y, KC_U , KC_I , KC_O , KC_P , KC_DEL , KC_BSPC , \ + KC_P4 , KC_P5, KC_P6 , KC_PMNS, KC_TAB , KC_A , KC_S , KC_D, KC_F , KC_G , KC_H, KC_J , KC_K , KC_L , KC_SCLN, KC_ENT , \ + KC_P1 , KC_P2, KC_P3 , KC_PPLS, KC_LSFT, KC_Z , KC_X, KC_C , KC_V , KC_B, KC_N , KC_M , KC_COMM, KC_DOT , KC_UP ,KC_RSFT , \ + MO(_FL), KC_P0, KC_PDOT, KC_PENT, KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC , KC_BSPC, KC_APP , KC_LEFT, KC_DOWN, KC_RGHT), + + /* Keymap _FL: Function Layer + */ + [_FL] = LAYOUT( + KC_P7 , KC_P8, KC_P9 , KC_VOLU, RESET , KC_Q , KC_W , KC_E, KC_R , KC_T , KC_Y, KC_U , KC_I , KC_LBRC, KC_RBRC, KC_INS , KC_BSPC , \ + KC_P4 , KC_P5, KC_P6 , KC_VOLD, KC_TAB , KC_A , KC_SLCK, KC_D, KC_F , KC_G , KC_H, KC_J , KC_K , KC_L , KC_QUOT, KC_BSLS , \ + KC_P1 , KC_P2, KC_P3 , KC_PEQL, KC_LSFT, KC_Z , KC_X, KC_CAPS, KC_V , KC_B, KC_NLCK, KC_M , KC_COMM, KC_DOT , KC_SLSH, KC_PGUP , \ + KC_END, KC_P0, KC_PDOT, KC_PENT, KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC , KC_BSPC, KC_APP , MO(_FL), KC_HOME, KC_PGDN), +}; diff --git a/keyboards/tkc/candybar/lefty/keymaps/via/keymap.c b/keyboards/tkc/candybar/lefty/keymaps/via/keymap.c new file mode 100644 index 0000000000..fd927195b2 --- /dev/null +++ b/keyboards/tkc/candybar/lefty/keymaps/via/keymap.c @@ -0,0 +1,52 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include QMK_KEYBOARD_H + +#define _BL 0 +#define _FL 1 +#define _AL 2 +#define _LL 3 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: Base Layer (Default Layer) + */ +[_BL] = LAYOUT( + KC_P7 , KC_P8, KC_P9 , KC_PAST, KC_ESC , KC_Q , KC_W , KC_E, KC_R , KC_T , KC_Y, KC_U , KC_I , KC_O , KC_P , KC_DEL , KC_BSPC , \ + KC_P4 , KC_P5, KC_P6 , KC_PMNS, KC_TAB , KC_A , KC_S , KC_D, KC_F , KC_G , KC_H, KC_J , KC_K , KC_L , KC_SCLN, KC_ENT , \ + KC_P1 , KC_P2, KC_P3 , KC_PPLS, KC_LSFT, KC_Z , KC_X, KC_C , KC_V , KC_B, KC_N , KC_M , KC_COMM, KC_DOT , KC_UP ,KC_RSFT , \ + MO(_FL), KC_P0, KC_PDOT, KC_PENT, KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC , KC_BSPC, KC_APP , KC_LEFT, KC_DOWN, KC_RGHT), + + /* Keymap _FL: Function Layer + */ + [_FL] = LAYOUT( + KC_P7 , KC_P8, KC_P9 , KC_VOLU, RESET , KC_Q , KC_W , KC_E, KC_R , KC_T , KC_Y, KC_U , KC_I , KC_LBRC, KC_RBRC, KC_INS , KC_BSPC , \ + KC_P4 , KC_P5, KC_P6 , KC_VOLD, KC_TAB , KC_A , KC_SLCK, KC_D, KC_F , KC_G , KC_H, KC_J , KC_K , KC_L , KC_QUOT, KC_BSLS , \ + KC_P1 , KC_P2, KC_P3 , KC_PEQL, KC_LSFT, KC_Z , KC_X, KC_CAPS, KC_V , KC_B, KC_NLCK, KC_M , KC_COMM, KC_DOT , KC_SLSH, KC_PGUP , \ + KC_END, KC_P0, KC_PDOT, KC_PENT, KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC , KC_BSPC, KC_APP , MO(_FL), KC_HOME, KC_PGDN), + + [_AL] = LAYOUT( + KC_P7 , KC_P8, KC_P9 , KC_VOLU, RESET , KC_Q , KC_W , KC_E, KC_R , KC_T , KC_Y, KC_U , KC_I , KC_LBRC, KC_RBRC, KC_INS , KC_BSPC , \ + KC_P4 , KC_P5, KC_P6 , KC_VOLD, KC_TAB , KC_A , KC_SLCK, KC_D, KC_F , KC_G , KC_H, KC_J , KC_K , KC_L , KC_QUOT, KC_BSLS , \ + KC_P1 , KC_P2, KC_P3 , KC_PEQL, KC_LSFT, KC_Z , KC_X, KC_CAPS, KC_V , KC_B, KC_NLCK, KC_M , KC_COMM, KC_DOT , KC_SLSH, KC_PGUP , \ + KC_END, KC_P0, KC_PDOT, KC_PENT, KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC , KC_BSPC, KC_APP , MO(_FL), KC_HOME, KC_PGDN), + + [_LL] = LAYOUT( + KC_P7 , KC_P8, KC_P9 , KC_VOLU, RESET , KC_Q , KC_W , KC_E, KC_R , KC_T , KC_Y, KC_U , KC_I , KC_LBRC, KC_RBRC, KC_INS , KC_BSPC , \ + KC_P4 , KC_P5, KC_P6 , KC_VOLD, KC_TAB , KC_A , KC_SLCK, KC_D, KC_F , KC_G , KC_H, KC_J , KC_K , KC_L , KC_QUOT, KC_BSLS , \ + KC_P1 , KC_P2, KC_P3 , KC_PEQL, KC_LSFT, KC_Z , KC_X, KC_CAPS, KC_V , KC_B, KC_NLCK, KC_M , KC_COMM, KC_DOT , KC_SLSH, KC_PGUP , \ + KC_END, KC_P0, KC_PDOT, KC_PENT, KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC , KC_BSPC, KC_APP , MO(_FL), KC_HOME, KC_PGDN), +}; diff --git a/keyboards/tkc/candybar/lefty/keymaps/via/rules.mk b/keyboards/tkc/candybar/lefty/keymaps/via/rules.mk new file mode 100644 index 0000000000..036bd6d1c3 --- /dev/null +++ b/keyboards/tkc/candybar/lefty/keymaps/via/rules.mk @@ -0,0 +1 @@ +VIA_ENABLE = yes
\ No newline at end of file diff --git a/keyboards/tkc/candybar/lefty/lefty.c b/keyboards/tkc/candybar/lefty/lefty.c new file mode 100644 index 0000000000..920811b833 --- /dev/null +++ b/keyboards/tkc/candybar/lefty/lefty.c @@ -0,0 +1,21 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "lefty.h" + +void matrix_init_kb(void) { + matrix_init_user(); +} diff --git a/keyboards/tkc/candybar/lefty/lefty.h b/keyboards/tkc/candybar/lefty/lefty.h new file mode 100644 index 0000000000..07af4b31bd --- /dev/null +++ b/keyboards/tkc/candybar/lefty/lefty.h @@ -0,0 +1,31 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once +#include "quantum.h" + + +#define LAYOUT( \ + k0d, k0e, k0f, k0g, k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, \ + k1d, k1e, k1f, k1g, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1c, \ + k2d, k2e, k2f, k2g, k20, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \ + k3d, k3e, k3f, k3g, k30, k31, k32, k35, k37, k38, k39, k3a, k3b, k3c \ +) { \ + { k00, k01 , k02, k03 , k04 , k05, k06 , k07, k08, k09, k0a, k0b , k0c, k0d, k0e, k0f, k0g } , \ + { k10, k11 , k12, k13 , k14 , k15, k16 , k17, k18, k19, k1a, KC_NO, k1c, k1d, k1e, k1f, k1g } , \ + { k20, KC_NO, k22, k23 , k24 , k25, k26 , k27, k28, k29, k2a, k2b , k2c, k2d, k2e, k2f, k2g } , \ + { k30, k31 , k32, KC_NO, KC_NO, k35, KC_NO, k37, k38, k39, k3a, k3b , k3c, k3d, k3e, k3f, k3g } \ +} diff --git a/keyboards/tkc/candybar/lefty/readme.md b/keyboards/tkc/candybar/lefty/readme.md new file mode 100644 index 0000000000..75ca1cbd80 --- /dev/null +++ b/keyboards/tkc/candybar/lefty/readme.md @@ -0,0 +1,15 @@ +# The Key Company Candybar + + + +The Key Company Candybar is a staggered 40% board with a numpad utilizing the STM32F072 microcontroller. + +* Keyboard Maintainer: [Terry Mathews](https://github.com/TerryMathews/) +* Hardware Supported: TKC Candybar +* Hardware Availability: [TheKey.Company](https://thekey.company/collections/candybar) + +Make example for this keyboard (after setting up your build environment): + + make tkc/candybar/lefty:default:dfu-util + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/tkc/candybar/lefty/rules.mk b/keyboards/tkc/candybar/lefty/rules.mk new file mode 100644 index 0000000000..1edad08350 --- /dev/null +++ b/keyboards/tkc/candybar/lefty/rules.mk @@ -0,0 +1,24 @@ +# MCU name +MCU = STM32F072 + +# Build Options +# comment out to disable the options. +# +# EXTRAFLAGS+=-flto +LTO_ENABLE = yes +BACKLIGHT_ENABLE = no +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration +## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.) +MOUSEKEY_ENABLE = no # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = no # Console for debug +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = no +SERIAL_LINK_ENABLE = no + + +# Enter lower-power sleep mode when on the ChibiOS idle thread +OPT_DEFS += -DCORTEX_ENABLE_WFI_IDLE=TRUE diff --git a/keyboards/tkc/candybar/mcuconf.h b/keyboards/tkc/candybar/mcuconf.h new file mode 100644 index 0000000000..faca3defdf --- /dev/null +++ b/keyboards/tkc/candybar/mcuconf.h @@ -0,0 +1,171 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _MCUCONF_H_ +#define _MCUCONF_H_ + +/* + * STM32F0xx drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 3...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +#define STM32F0xx_MCUCONF + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 +#define STM32_HSI_ENABLED TRUE +#define STM32_HSI14_ENABLED TRUE +#define STM32_HSI48_ENABLED FALSE +#define STM32_LSI_ENABLED TRUE +#define STM32_HSE_ENABLED FALSE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSI_DIV2 +#define STM32_PREDIV_VALUE 1 +#define STM32_PLLMUL_VALUE 12 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE STM32_PPRE_DIV1 +#define STM32_ADCSW STM32_ADCSW_HSI14 +#define STM32_ADCPRE STM32_ADCPRE_DIV4 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_ADCPRE STM32_ADCPRE_DIV4 +#define STM32_ADCSW STM32_ADCSW_HSI14 +#define STM32_USBSW STM32_USBSW_HSI48 +#define STM32_CECSW STM32_CECSW_HSI +#define STM32_I2C1SW STM32_I2C1SW_HSI +#define STM32_USART1SW STM32_USART1SW_PCLK +#define STM32_RTCSEL STM32_RTCSEL_LSI + +/* + * ADC driver system settings. + */ +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_IRQ_PRIORITY 2 +#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 2 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_1_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI2_3_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI4_15_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 3 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM14 FALSE +#define STM32_GPT_TIM1_IRQ_PRIORITY 2 +#define STM32_GPT_TIM2_IRQ_PRIORITY 2 +#define STM32_GPT_TIM3_IRQ_PRIORITY 2 +#define STM32_GPT_TIM14_IRQ_PRIORITY 2 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 3 +#define STM32_I2C_I2C2_IRQ_PRIORITY 3 +#define STM32_I2C_USE_DMA TRUE +#define STM32_I2C_I2C1_DMA_PRIORITY 1 +#define STM32_I2C_I2C2_DMA_PRIORITY 1 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 3 +#define STM32_ICU_TIM2_IRQ_PRIORITY 3 +#define STM32_ICU_TIM3_IRQ_PRIORITY 3 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_TIM1_IRQ_PRIORITY 3 +#define STM32_PWM_TIM2_IRQ_PRIORITY 3 +#define STM32_PWM_TIM3_IRQ_PRIORITY 3 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 FALSE +#define STM32_SERIAL_USART1_PRIORITY 3 +#define STM32_SERIAL_USART2_PRIORITY 3 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 2 +#define STM32_SPI_SPI2_IRQ_PRIORITY 2 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 2 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 3 +#define STM32_UART_USART2_IRQ_PRIORITY 3 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_LP_IRQ_PRIORITY 3 + +#endif /* _MCUCONF_H_ */ diff --git a/keyboards/tkc/candybar/righty/config.h b/keyboards/tkc/candybar/righty/config.h new file mode 100644 index 0000000000..5004537846 --- /dev/null +++ b/keyboards/tkc/candybar/righty/config.h @@ -0,0 +1,115 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x544B //TK +#define PRODUCT_ID 0x0002 +#define DEVICE_VER 0x0006 +#define MANUFACTURER The Key Company +#define PRODUCT Candybar +#define DESCRIPTION A compact staggered 40% keyboard with attached numpad + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 17 +#define DIODE_DIRECTION COL2ROW +#define MATRIX_ROW_PINS { A8, A9, A10, A13 } +#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, B0, B1, B2, B10, B11, B12, B13, B14, B15 } + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +//#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +// #define WS2812_LED_N 2 +// #define RGBLED_NUM WS2812_LED_N +// #define WS2812_TIM_N 2 +// #define WS2812_TIM_CH 2 +// #define PORT_WS2812 GPIOA +// #define PIN_WS2812 1 +// #define WS2812_DMA_STREAM STM32_DMA1_STREAM2 // DMA stream for TIMx_UP (look up in reference manual under DMA Channel selection) +//#define WS2812_DMA_CHANNEL 7 // DMA channel for TIMx_UP +//#define WS2812_EXTERNAL_PULLUP diff --git a/keyboards/tkc/candybar/righty/info.json b/keyboards/tkc/candybar/righty/info.json new file mode 100644 index 0000000000..81dc4f8ec5 --- /dev/null +++ b/keyboards/tkc/candybar/righty/info.json @@ -0,0 +1,16 @@ +{ + "keyboard_name": "TKC Candybar", + "url": "", + "maintainer": "terrymathews", + "width": 17, + "height": 4, + "layouts": { + "LAYOUT": { + "layout": [ + {"label":"Esc", "x":0, "y":0}, {"label":"Q", "x":1, "y":0}, {"label":"W", "x":2, "y":0}, {"label":"E", "x":3, "y":0}, {"label":"R", "x":4, "y":0}, {"label":"T", "x":5, "y":0}, {"label":"Y", "x":6, "y":0}, {"label":"U", "x":7, "y":0}, {"label":"I", "x":8, "y":0}, {"label":"O", "x":9, "y":0}, {"label":"P", "x":10, "y":0}, {"label":"Del", "x":11, "y":0}, {"label":"BkSp", "x":12, "y":0}, {"label":"7", "x":13, "y":0}, {"label":"8", "x":14, "y":0}, {"label":"9", "x":15, "y":0}, {"label":"*", "x":16, "y":0}, + {"label":"Tab", "x":0, "y":1, "w":1.25}, {"label":"A", "x":1.25, "y":1}, {"label":"S", "x":2.25, "y":1}, {"label":"D", "x":3.25, "y":1}, {"label":"F", "x":4.25, "y":1}, {"label":"G", "x":5.25, "y":1}, {"label":"H", "x":6.25, "y":1}, {"label":"J", "x":7.25, "y":1}, {"label":"K", "x":8.25, "y":1}, {"label":"L", "x":9.25, "y":1}, {"label":":", "x":10.25, "y":1}, {"label":"Enter", "x":11.25, "y":1, "w":1.75}, {"label":"4", "x":13, "y":1}, {"label":"5", "x":14, "y":1}, {"label":"6", "x":15, "y":1}, {"label":"-", "x":16, "y":1}, + {"label":"Shift", "x":0, "y":2, "w":1.75}, {"label":"Z", "x":1.75, "y":2}, {"label":"X", "x":2.75, "y":2}, {"label":"C", "x":3.75, "y":2}, {"label":"V", "x":4.75, "y":2}, {"label":"B", "x":5.75, "y":2}, {"label":"N", "x":6.75, "y":2}, {"label":"M", "x":7.75, "y":2}, {"label":"<", "x":8.75, "y":2}, {"label":">", "x":9.75, "y":2}, {"label":"Shift", "x":10.75, "y":2, "w":1.25}, {"label":"↑", "x":12, "y":2}, {"label":"1", "x":13, "y":2}, {"label":"2", "x":14, "y":2}, {"label":"3", "x":15, "y":2}, {"label":"+", "x":16, "y":2}, + {"label":"Ctrl", "x":0, "y":3, "w":1.25}, {"label":"GUI", "x":1.25, "y":3, "w":1.25}, {"label":"Alt", "x":2.5, "y":3, "w":1.25}, {"x":3.75, "y":3, "w":1.75}, {"x":5.5, "y":3, "w":1}, {"label":"Backspace", "x":6.5, "y":3, "w":2.25}, {"label":"Menu", "x":8.75, "y":3, "w":1.25}, {"label":"Fn", "x":10, "y":3}, {"label":"←", "x":11, "y":3}, {"label":"↓", "x":12, "y":3}, {"label":"→", "x":13, "y":3}, {"label":"0", "x":14, "y":3}, {"label":".", "x":15, "y":3}, {"label":"Enter", "x":16, "y":3}] + } + } +} diff --git a/keyboards/tkc/candybar/righty/keymaps/default/keymap.c b/keyboards/tkc/candybar/righty/keymaps/default/keymap.c new file mode 100644 index 0000000000..8f4cc08c74 --- /dev/null +++ b/keyboards/tkc/candybar/righty/keymaps/default/keymap.c @@ -0,0 +1,38 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include QMK_KEYBOARD_H + +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: Base Layer (Default Layer) + */ +[_BL] = LAYOUT( + KC_ESC,KC_Q,KC_W,KC_E,KC_R,KC_T,KC_Y,KC_U,KC_I,KC_O,KC_P,KC_DEL,KC_BSPC,KC_P7,KC_P8,KC_P9,KC_PAST, \ + KC_TAB,KC_A,KC_S,KC_D,KC_F,KC_G,KC_H,KC_J,KC_K,KC_L,KC_SCLN,KC_ENT,KC_P4,KC_P5,KC_P6,KC_PMNS, \ + KC_LSFT,KC_Z,KC_X,KC_C,KC_V,KC_B,KC_N,KC_M,KC_COMM,KC_DOT,KC_RSFT,KC_UP,KC_P1,KC_P2,KC_P3,KC_PPLS, \ + KC_LCTL,KC_LGUI,KC_LALT,KC_SPC,KC_SPC,KC_BSPC,KC_APP,MO(_FL),KC_LEFT,KC_DOWN,KC_RGHT,KC_P0,KC_PDOT,KC_PENT), + + /* Keymap _FL: Function Layer + */ +[_FL] = LAYOUT( + RESET,KC_Q,KC_W,KC_E,KC_R,KC_T,KC_Y,KC_U,KC_I,KC_LBRC,KC_RBRC,KC_INS,KC_BSPC,KC_P7,KC_P8,KC_P9,KC_VOLU, \ + KC_TAB,KC_A,KC_SLCK,KC_D,KC_F,KC_G,KC_H,KC_J,KC_K,KC_L,KC_QUOT,KC_BSLS,KC_P4,KC_P5,KC_P6,KC_VOLD, \ + KC_LSFT,KC_Z,KC_X,KC_CAPS,KC_V,KC_B,KC_NLCK,KC_M,KC_COMM,KC_DOT,KC_SLSH,KC_PGUP,KC_P1,KC_P2,KC_P3,KC_PEQL, \ + KC_LCTL,KC_LGUI,KC_LALT,KC_SPC,KC_SPC,KC_BSPC,KC_APP,MO(_FL),KC_HOME,KC_PGDN,KC_END,KC_P0,KC_PDOT,KC_PENT), +}; diff --git a/keyboards/tkc/candybar/righty/keymaps/via/keymap.c b/keyboards/tkc/candybar/righty/keymaps/via/keymap.c new file mode 100644 index 0000000000..fb8ac93d46 --- /dev/null +++ b/keyboards/tkc/candybar/righty/keymaps/via/keymap.c @@ -0,0 +1,52 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include QMK_KEYBOARD_H + +#define _BL 0 +#define _FL 1 +#define _AL 2 +#define _LL 3 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: Base Layer (Default Layer) + */ +[_BL] = LAYOUT( + KC_ESC,KC_Q,KC_W,KC_E,KC_R,KC_T,KC_Y,KC_U,KC_I,KC_O,KC_P,KC_DEL,KC_BSPC,KC_P7,KC_P8,KC_P9,KC_PAST, \ + KC_TAB,KC_A,KC_S,KC_D,KC_F,KC_G,KC_H,KC_J,KC_K,KC_L,KC_SCLN,KC_ENT,KC_P4,KC_P5,KC_P6,KC_PMNS, \ + KC_LSFT,KC_Z,KC_X,KC_C,KC_V,KC_B,KC_N,KC_M,KC_COMM,KC_DOT,KC_RSFT,KC_UP,KC_P1,KC_P2,KC_P3,KC_PPLS, \ + KC_LCTL,KC_LGUI,KC_LALT,KC_SPC,KC_SPC,KC_BSPC,KC_APP,MO(_FL),KC_LEFT,KC_DOWN,KC_RGHT,KC_P0,KC_PDOT,KC_PENT), + + /* Keymap _FL: Function Layer + */ +[_FL] = LAYOUT( + RESET,KC_Q,KC_W,KC_E,KC_R,KC_T,KC_Y,KC_U,KC_I,KC_LBRC,KC_RBRC,KC_INS,KC_BSPC,KC_P7,KC_P8,KC_P9,KC_VOLU, \ + KC_TAB,KC_A,KC_SLCK,KC_D,KC_F,KC_G,KC_H,KC_J,KC_K,KC_L,KC_QUOT,KC_BSLS,KC_P4,KC_P5,KC_P6,KC_VOLD, \ + KC_LSFT,KC_Z,KC_X,KC_CAPS,KC_V,KC_B,KC_NLCK,KC_M,KC_COMM,KC_DOT,KC_SLSH,KC_PGUP,KC_P1,KC_P2,KC_P3,KC_PEQL, \ + KC_LCTL,KC_LGUI,KC_LALT,KC_SPC,KC_SPC,KC_BSPC,KC_APP,MO(_FL),KC_HOME,KC_PGDN,KC_END,KC_P0,KC_PDOT,KC_PENT), + + [_AL] = LAYOUT( + RESET,KC_Q,KC_W,KC_E,KC_R,KC_T,KC_Y,KC_U,KC_I,KC_LBRC,KC_RBRC,KC_INS,KC_BSPC,KC_P7,KC_P8,KC_P9,KC_VOLU, \ + KC_TAB,KC_A,KC_SLCK,KC_D,KC_F,KC_G,KC_H,KC_J,KC_K,KC_L,KC_QUOT,KC_BSLS,KC_P4,KC_P5,KC_P6,KC_VOLD, \ + KC_LSFT,KC_Z,KC_X,KC_CAPS,KC_V,KC_B,KC_NLCK,KC_M,KC_COMM,KC_DOT,KC_SLSH,KC_PGUP,KC_P1,KC_P2,KC_P3,KC_PEQL, \ + KC_LCTL,KC_LGUI,KC_LALT,KC_SPC,KC_SPC,KC_BSPC,KC_APP,MO(_FL),KC_HOME,KC_PGDN,KC_END,KC_P0,KC_PDOT,KC_PENT), + + [_LL] = LAYOUT( + RESET,KC_Q,KC_W,KC_E,KC_R,KC_T,KC_Y,KC_U,KC_I,KC_LBRC,KC_RBRC,KC_INS,KC_BSPC,KC_P7,KC_P8,KC_P9,KC_VOLU, \ + KC_TAB,KC_A,KC_SLCK,KC_D,KC_F,KC_G,KC_H,KC_J,KC_K,KC_L,KC_QUOT,KC_BSLS,KC_P4,KC_P5,KC_P6,KC_VOLD, \ + KC_LSFT,KC_Z,KC_X,KC_CAPS,KC_V,KC_B,KC_NLCK,KC_M,KC_COMM,KC_DOT,KC_SLSH,KC_PGUP,KC_P1,KC_P2,KC_P3,KC_PEQL, \ + KC_LCTL,KC_LGUI,KC_LALT,KC_SPC,KC_SPC,KC_BSPC,KC_APP,MO(_FL),KC_HOME,KC_PGDN,KC_END,KC_P0,KC_PDOT,KC_PENT), +}; diff --git a/keyboards/tkc/candybar/righty/keymaps/via/rules.mk b/keyboards/tkc/candybar/righty/keymaps/via/rules.mk new file mode 100644 index 0000000000..036bd6d1c3 --- /dev/null +++ b/keyboards/tkc/candybar/righty/keymaps/via/rules.mk @@ -0,0 +1 @@ +VIA_ENABLE = yes
\ No newline at end of file diff --git a/keyboards/tkc/candybar/righty/readme.md b/keyboards/tkc/candybar/righty/readme.md new file mode 100644 index 0000000000..4e2a0f8474 --- /dev/null +++ b/keyboards/tkc/candybar/righty/readme.md @@ -0,0 +1,15 @@ +# The Key Company Candybar + + + +The Key Company Candybar is a staggered 40% board with a numpad utilizing the STM32F072 microcontroller. + +* Keyboard Maintainer: [Terry Mathews](https://github.com/TerryMathews/) +* Hardware Supported: TKC Candybar +* Hardware Availability: [TheKey.Company](https://thekey.company/collections/candybar) + +Make example for this keyboard (after setting up your build environment): + + make tkc/candybar/righty:default:dfu-util + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/tkc/candybar/righty/righty.c b/keyboards/tkc/candybar/righty/righty.c new file mode 100644 index 0000000000..c3b6115747 --- /dev/null +++ b/keyboards/tkc/candybar/righty/righty.c @@ -0,0 +1,17 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "righty.h" diff --git a/keyboards/tkc/candybar/righty/righty.h b/keyboards/tkc/candybar/righty/righty.h new file mode 100644 index 0000000000..67e0238839 --- /dev/null +++ b/keyboards/tkc/candybar/righty/righty.h @@ -0,0 +1,30 @@ +/* Copyright 2018 Jack Humbert + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once +#include "quantum.h" + +#define LAYOUT( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0e, k0f, k0g, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1c, k1d, k1e, k1f, k1g, \ + k20, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, k2e, k2f, k2g, \ + k30, k31, k32, k35, k37, k38, k39, k3a, k3b, k3c, k3d, k3e, k3f, k3g \ +) { \ + { k00, k01 , k02, k03 , k04 , k05, k06 , k07, k08, k09, k0a, k0b , k0c, k0d, k0e, k0f, k0g } , \ + { k10, k11 , k12, k13 , k14 , k15, k16 , k17, k18, k19, k1a, KC_NO, k1c, k1d, k1e, k1f, k1g } , \ + { k20, KC_NO, k22, k23 , k24 , k25, k26 , k27, k28, k29, k2a, k2b , k2c, k2d, k2e, k2f, k2g } , \ + { k30, k31 , k32, KC_NO, KC_NO, k35, KC_NO, k37, k38, k39, k3a, k3b , k3c, k3d, k3e, k3f, k3g } \ +} diff --git a/keyboards/tkc/candybar/righty/rules.mk b/keyboards/tkc/candybar/righty/rules.mk new file mode 100644 index 0000000000..1edad08350 --- /dev/null +++ b/keyboards/tkc/candybar/righty/rules.mk @@ -0,0 +1,24 @@ +# MCU name +MCU = STM32F072 + +# Build Options +# comment out to disable the options. +# +# EXTRAFLAGS+=-flto +LTO_ENABLE = yes +BACKLIGHT_ENABLE = no +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration +## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.) +MOUSEKEY_ENABLE = no # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = no # Console for debug +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = no +SERIAL_LINK_ENABLE = no + + +# Enter lower-power sleep mode when on the ChibiOS idle thread +OPT_DEFS += -DCORTEX_ENABLE_WFI_IDLE=TRUE |