diff options
Diffstat (limited to 'keyboards/gh60/rules.mk')
| -rw-r--r-- | keyboards/gh60/rules.mk | 137 |
1 files changed, 69 insertions, 68 deletions
diff --git a/keyboards/gh60/rules.mk b/keyboards/gh60/rules.mk index 73f4bd76e8..b3c5c7271c 100644 --- a/keyboards/gh60/rules.mk +++ b/keyboards/gh60/rules.mk @@ -1,68 +1,69 @@ -
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-# CONSOLE_ENABLE ?= yes # Console for debug(+400)
-# COMMAND_ENABLE ?= yes # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-# MIDI_ENABLE ?= YES # MIDI controls
-# UNICODE_ENABLE ?= YES # Unicode
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
+# project specific files +SRC = led.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID |