summaryrefslogtreecommitdiff
path: root/keyboards/ergodox/ergodone/rules.mk
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/ergodox/ergodone/rules.mk')
-rw-r--r--keyboards/ergodox/ergodone/rules.mk91
1 files changed, 0 insertions, 91 deletions
diff --git a/keyboards/ergodox/ergodone/rules.mk b/keyboards/ergodox/ergodone/rules.mk
deleted file mode 100644
index e7fd4e0aba..0000000000
--- a/keyboards/ergodox/ergodone/rules.mk
+++ /dev/null
@@ -1,91 +0,0 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean,
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-# (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
-# # project specific files
-SRC = \
- twimaster.c \
- matrix.c \
- expander.c \
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = no # Commands for debug and configuration
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-USB_6KRO_ENABLE = no # USB 6key Rollover
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-KEYMAP_IN_EEPROM_ENABLE = no # External keymap in eeprom
-KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor
-SOFTPWM_LED_ENABLE = no # Enable SoftPWM to drive backlight
-FADING_LED_ENABLE = no # Enable fading backlight
-BREATHING_LED_ENABLE = no # Enable breathing backlight
-LEDMAP_ENABLE = no # Enable LED mapping
-LEDMAP_IN_EEPROM_ENABLE = no # Read LED mapping from eeprom
-ONEHAND_ENABLE = no # Disable Onehand
-RGBLIGHT_ENABLE = no
-MIDI_ENABLE = no