diff options
Diffstat (limited to 'keyboards/dc01')
| -rw-r--r-- | keyboards/dc01/arrow/rules.mk | 59 | ||||
| -rw-r--r-- | keyboards/dc01/left/rules.mk | 59 | ||||
| -rw-r--r-- | keyboards/dc01/numpad/rules.mk | 59 | ||||
| -rw-r--r-- | keyboards/dc01/right/rules.mk | 59 |
4 files changed, 44 insertions, 192 deletions
diff --git a/keyboards/dc01/arrow/rules.mk b/keyboards/dc01/arrow/rules.mk index 8426df1bd4..56a9cfc49c 100644 --- a/keyboards/dc01/arrow/rules.mk +++ b/keyboards/dc01/arrow/rules.mk @@ -1,54 +1,15 @@ -SRC += matrix.c \ - i2c_slave.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable @@ -71,3 +32,5 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) NO_USB_STARTUP_CHECK = yes # Disable initialization only when usb is plugged in CUSTOM_MATRIX = yes # Use custom matrix +SRC += matrix.c \ + i2c_slave.c diff --git a/keyboards/dc01/left/rules.mk b/keyboards/dc01/left/rules.mk index 8a0d061953..9e34a0a808 100644 --- a/keyboards/dc01/left/rules.mk +++ b/keyboards/dc01/left/rules.mk @@ -1,54 +1,15 @@ -SRC += matrix.c \ - i2c_master.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable @@ -70,3 +31,5 @@ AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) CUSTOM_MATRIX = yes # Use custom matrix +SRC += matrix.c \ + i2c_master.c diff --git a/keyboards/dc01/numpad/rules.mk b/keyboards/dc01/numpad/rules.mk index 420534f8ca..674ef1d026 100644 --- a/keyboards/dc01/numpad/rules.mk +++ b/keyboards/dc01/numpad/rules.mk @@ -1,54 +1,15 @@ -SRC += matrix.c \ - i2c_slave.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable @@ -71,6 +32,8 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) NO_USB_STARTUP_CHECK = yes # Disable initialization only when usb is plugged in CUSTOM_MATRIX = yes # Use custom matrix +SRC += matrix.c \ + i2c_slave.c # Community layouts supported LAYOUTS = numpad_5x4 ortho_5x4 diff --git a/keyboards/dc01/right/rules.mk b/keyboards/dc01/right/rules.mk index 8426df1bd4..56a9cfc49c 100644 --- a/keyboards/dc01/right/rules.mk +++ b/keyboards/dc01/right/rules.mk @@ -1,54 +1,15 @@ -SRC += matrix.c \ - i2c_slave.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable @@ -71,3 +32,5 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) NO_USB_STARTUP_CHECK = yes # Disable initialization only when usb is plugged in CUSTOM_MATRIX = yes # Use custom matrix +SRC += matrix.c \ + i2c_slave.c |