diff options
Diffstat (limited to 'keyboard/hhkb/README')
| -rw-r--r-- | keyboard/hhkb/README | 151 |
1 files changed, 151 insertions, 0 deletions
diff --git a/keyboard/hhkb/README b/keyboard/hhkb/README new file mode 100644 index 0000000000..65f7dcab5a --- /dev/null +++ b/keyboard/hhkb/README @@ -0,0 +1,151 @@ +Alternative Controller for HHKB +=============================== + +Feature +------- +- Mouse Keys +- NKRO on USB(PJRC Tennsy only) +- Keymap Layers + + +Customize Keymap +---------------- +see keymap.c. + + + +Build +===== +PJRC Teensy +----------- +0. Edit matrix.c. + adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts) +1. Define macros in config_pjrc.h.(Optional) + VENDOR_ID, PRODUCT_ID and string descriptor. + IS_COMMAND +2. Edit Makefile for MCU setting and build options. + MCU, F_CPU + MOUSEKEY_ENABLE, EXTRAKEY_ENABLE, NKRO_ENABLE +3. Build hex file. + $ make -f Makefile.pjrc +4. Program MCU. + $ make -f Makefile.pjrc program + + +V-USB +----- +0. Edit matrix.c and usbconfig.h. + adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts) + define macros for V-USB in usbconfig.h. +1. Define macros in config_vusb.h.(Optional) + IS_COMMAND +2. Edit Makefile.vusb for MCU setting and build options. + MCU, F_CPU + MOUSEKEY_ENABLE, EXTRAKEY_ENABLE +3. Build hex file. + $ make -f Makefile.vusb +4. Program MCU. + $ make -f Makefile.vusb program + + Using a bootloader to program for convenience is recommended. + Once program this V-USB bootloader at first, you can program MCU without + extra programmer. You should have reset switch to start up as bootloader + mode in this case. + USBaspLoader: + http://www.obdev.at/products/vusb/usbasploader.html + + +iWRAP +----- +0. Edit matrix.c and usbconfig.h. + adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts) + define macros for V-USB in usbconfig.h. +1. Define macros in config_iwrap.h.(Optional) + IS_COMMAND +2. Edit Makefile.iwrap for MCU setting and build options. + MCU, F_CPU + MOUSEKEY_ENABLE, EXTRAKEY_ENABLE +3. Build hex file. + $ make -f Makefile.iwrap +4. Program MCU. + $ make -f Makefile.iwrap program + + + +Hardware +======== +PJRC Teensy +----------- + +---------------+ + | Teensy++ | + | | + | | HHKB + | | ~~~~ + | PB0-2|------->ROW(6-8) + | PB3-5|------->COL(9-11) + | PB6|------->ENABLE(12) + | PE6|<-------KEY(4) + | PE7|------->PREV(5) + | | + | | + | | + +---------------+ + + +V-USB +----- + +---+ +---------------+ +USB GND | | ATmega168 | +~~~ C3 | | +5V <-------+--------+---|Vcc,AVCC | HHKB + R1 | | ~~~~ +D- <----+--+-----R2-----|INT1 PB2-4|------->ROW(6-8) +D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11) + Z1 Z2 | PC3|------->ENABLE(12) +GND<----+---+-----------|GND PB0|<-------KEY(4) + | PB1|------->PREV(5) + | | + GND+-C2--+--|XTAL1 RXD|------->Debug Console + X1 | TXD|<-------Debug Console + GND+-C3--+--|XTAL2 RST|---SW--+GND + +---------------+ +R1: 1.5K Ohm +R2,R3: 68 Ohm +Z1,Z2: Zener 3.6V +C1,C2: 22pF +C3: 0.1uF +X1: Crystal 20MHz(16MHz/12MHz) +SW: Push Switch(Optional for bootloader) + + +iWRAP +----- + +---------------+ WT12 + 5V | ATmega168 | 5V/3.3V~~~~ + +-----+---|Vcc,AVCC PC4|---/--->iWRAP(RxD) +USB | C3 | PC5|<--/----iWRAP(TxD) +~~~ | + | | +5V <--BATT + GND | | HHKB + R1 | | ~~~~ +D- <----+-----+--R2-----|INT1 PB2-4|------->ROW(6-8) +D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11) + Z1 Z2 | PC3|------->ENABLE(12) +GND<----+---+-----------|GND PB0|<-------KEY(4) + | PB1|------->PREV(5) + | | + GND+-C2--+--|XTAL1 RXD|------->Debug Console + X1 | TXD|<-------Debug Console + GND+-C3--+--|XTAL2 RST|---SW--+GND + +---------------+ + +R1: 1.5K Ohm +R2,R3: 68 Ohm +Z1,Z2: Zener 3.6V +C1,C2: 22pF +C3: 0.1uF +X1: Crystal 12MHz +SW: Push Switch(Optional) +BATT: Li-Po Battery, Battery Charger and Voltage Regulator(5V and 3.3V). + + +EOF |