clang-format changes

1 files changed, 48 insertions, 50 deletions

diff --git a/quantum/template/ps2avrgb/usbconfig.h b/quantum/template/ps2avrgb/usbconfig.h
index 4efa935d99..9ef232f045 100644
--- a/quantum/template/ps2avrgb/usbconfig.h
+++ b/quantum/template/ps2avrgb/usbconfig.h
@@ -14,15 +14,15 @@ section at the end of this file).
 
 /* ---------------------------- Hardware Config ---------------------------- */
 
-#define USB_CFG_IOPORTNAME      D
+#define USB_CFG_IOPORTNAME D
 /* This is the port where the USB bus is connected. When you configure it to
  * "B", the registers PORTB, PINB and DDRB will be used.
  */
-#define USB_CFG_DMINUS_BIT      3
+#define USB_CFG_DMINUS_BIT 3
 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
  * This may be any bit in the port.
  */
-#define USB_CFG_DPLUS_BIT       2
+#define USB_CFG_DPLUS_BIT 2
 /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
  * This may be any bit in the port. Please note that D+ must also be connected
  * to interrupt pin INT0! [You can also use other interrupts, see section
@@ -31,7 +31,7 @@ section at the end of this file).
  * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
  * markers every millisecond.]
  */
-#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+#define USB_CFG_CLOCK_KHZ (F_CPU / 1000)
 /* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
  * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
  * require no crystal, they tolerate +/- 1% deviation from the nominal
@@ -40,7 +40,7 @@ section at the end of this file).
  * Since F_CPU should be defined to your actual clock rate anyway, you should
  * not need to modify this setting.
  */
-#define USB_CFG_CHECK_CRC       0
+#define USB_CFG_CHECK_CRC 0
 /* Define this to 1 if you want that the driver checks integrity of incoming
  * data packets (CRC checks). CRC checks cost quite a bit of code size and are
  * currently only available for 18 MHz crystal clock. You must choose
@@ -63,18 +63,18 @@ section at the end of this file).
 
 /* --------------------------- Functional Range ---------------------------- */
 
-#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
+#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
 /* Define this to 1 if you want to compile a version with two endpoints: The
  * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
  * number).
  */
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
 /* Define this to 1 if you want to compile a version with three endpoints: The
  * default control endpoint 0, an interrupt-in endpoint 3 (or the number
  * configured below) and a catch-all default interrupt-in endpoint as above.
  * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
  */
-#define USB_CFG_EP3_NUMBER              3
+#define USB_CFG_EP3_NUMBER 3
 /* If the so-called endpoint 3 is used, it can now be configured to any other
  * endpoint number (except 0) with this macro. Default if undefined is 3.
  */
@@ -84,13 +84,13 @@ section at the end of this file).
  * Since the token is toggled BEFORE sending any data, the first packet is
  * sent with the oposite value of this configuration!
  */
-#define USB_CFG_IMPLEMENT_HALT          0
+#define USB_CFG_IMPLEMENT_HALT 0
 /* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
  * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
  * it is required by the standard. We have made it a config option because it
  * bloats the code considerably.
  */
-#define USB_CFG_SUPPRESS_INTR_CODE      0
+#define USB_CFG_SUPPRESS_INTR_CODE 0
 /* Define this to 1 if you want to declare interrupt-in endpoints, but don't
  * want to send any data over them. If this macro is defined to 1, functions
  * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
@@ -98,48 +98,48 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
+#define USB_CFG_INTR_POLL_INTERVAL 1
 /* If you compile a version with endpoint 1 (interrupt-in), this is the poll
  * interval. The value is in milliseconds and must not be less than 10 ms for
  * low speed devices.
  */
-#define USB_CFG_IS_SELF_POWERED         0
+#define USB_CFG_IS_SELF_POWERED 0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
+#define USB_CFG_MAX_BUS_POWER 500
 /* Set this variable to the maximum USB bus power consumption of your device.
  * The value is in milliamperes. [It will be divided by two since USB
  * communicates power requirements in units of 2 mA.]
  */
-#define USB_CFG_IMPLEMENT_FN_WRITE      1
+#define USB_CFG_IMPLEMENT_FN_WRITE 1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
  * bytes.
  */
-#define USB_CFG_IMPLEMENT_FN_READ       0
+#define USB_CFG_IMPLEMENT_FN_READ 0
 /* Set this to 1 if you need to send control replies which are generated
  * "on the fly" when usbFunctionRead() is called. If you only want to send
  * data from a static buffer, set it to 0 and return the data from
  * usbFunctionSetup(). This saves a couple of bytes.
  */
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
 /* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
  * You must implement the function usbFunctionWriteOut() which receives all
  * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
  * can be found in 'usbRxToken'.
  */
-#define USB_CFG_HAVE_FLOWCONTROL        0
+#define USB_CFG_HAVE_FLOWCONTROL 0
 /* Define this to 1 if you want flowcontrol over USB data. See the definition
  * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
  * usbdrv.h.
  */
-#define USB_CFG_DRIVER_FLASH_PAGE       0
+#define USB_CFG_DRIVER_FLASH_PAGE 0
 /* If the device has more than 64 kBytes of flash, define this to the 64 k page
  * where the driver's constants (descriptors) are located. Or in other words:
  * Define this to 1 for boot loaders on the ATMega128.
  */
-#define USB_CFG_LONG_TRANSFERS          0
+#define USB_CFG_LONG_TRANSFERS 0
 /* Define this to 1 if you want to send/receive blocks of more than 254 bytes
  * in a single control-in or control-out transfer. Note that the capability
  * for long transfers increases the driver size.
@@ -160,7 +160,7 @@ section at the end of this file).
 /* This macro (if defined) is executed when a USB SET_ADDRESS request was
  * received.
  */
-#define USB_COUNT_SOF                   1
+#define USB_COUNT_SOF 1
 /* define this macro to 1 if you need the global variable "usbSofCount" which
  * counts SOF packets. This feature requires that the hardware interrupt is
  * connected to D- instead of D+.
@@ -184,7 +184,7 @@ section at the end of this file).
  * Please note that Start Of Frame detection works only if D- is wired to the
  * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
  */
-#define USB_CFG_CHECK_DATA_TOGGLING     0
+#define USB_CFG_CHECK_DATA_TOGGLING 0
 /* define this macro to 1 if you want to filter out duplicate data packets
  * sent by the host. Duplicates occur only as a consequence of communication
  * errors, when the host does not receive an ACK. Please note that you need to
@@ -192,11 +192,11 @@ section at the end of this file).
  * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
  * for each control- and out-endpoint to check for duplicate packets.
  */
-#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
 /* define this macro to 1 if you want the function usbMeasureFrameLength()
  * compiled in. This function can be used to calibrate the AVR's RC oscillator.
  */
-#define USB_USE_FAST_CRC                0
+#define USB_USE_FAST_CRC 0
 /* The assembler module has two implementations for the CRC algorithm. One is
  * faster, the other is smaller. This CRC routine is only used for transmitted
  * messages where timing is not critical. The faster routine needs 31 cycles
@@ -207,7 +207,7 @@ section at the end of this file).
 
 /* -------------------------- Device Description --------------------------- */
 
-#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
 /* USB vendor ID for the device, low byte first. If you have registered your
  * own Vendor ID, define it here. Otherwise you may use one of obdev's free
  * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
@@ -216,7 +216,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
 /* This is the ID of the product, low byte first. It is interpreted in the
  * scope of the vendor ID. If you have registered your own VID with usb.org
  * or if you have licensed a PID from somebody else, define it here. Otherwise
@@ -227,10 +227,10 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION 0x00, 0x02
 /* Version number of the device: Minor number first, then major number.
  */
-#define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
+#define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
 #define USB_CFG_VENDOR_NAME_LEN 13
 /* These two values define the vendor name returned by the USB device. The name
  * must be given as a list of characters under single quotes. The characters
@@ -240,7 +240,7 @@ section at the end of this file).
  * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
  * details.
  */
-#define USB_CFG_DEVICE_NAME     'p', 's', '2', 'a', 'v', 'r', 'G', 'B'
+#define USB_CFG_DEVICE_NAME 'p', 's', '2', 'a', 'v', 'r', 'G', 'B'
 #define USB_CFG_DEVICE_NAME_LEN 8
 /* Same as above for the device name. If you don't want a device name, undefine
  * the macros. See the file USB-IDs-for-free.txt before you assign a name if
@@ -255,20 +255,20 @@ section at the end of this file).
  * to fine tune control over USB descriptors such as the string descriptor
  * for the serial number.
  */
-#define USB_CFG_DEVICE_CLASS        0
-#define USB_CFG_DEVICE_SUBCLASS     0
+#define USB_CFG_DEVICE_CLASS 0
+#define USB_CFG_DEVICE_SUBCLASS 0
 /* See USB specification if you want to conform to an existing device class.
  * Class 0xff is "vendor specific".
  */
-#define USB_CFG_INTERFACE_CLASS     3   /* HID */
-#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
-#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
+#define USB_CFG_INTERFACE_CLASS 3    /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
 /* See USB specification if you want to conform to an existing device class or
  * protocol. The following classes must be set at interface level:
  * HID class is 3, no subclass and protocol required (but may be useful!)
  * CDC class is 2, use subclass 2 and protocol 1 for ACM
  */
-#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
 /* Define this to the length of the HID report descriptor, if you implement
  * an HID device. Otherwise don't define it or define it to 0.
  * If you use this define, you must add a PROGMEM character array named
@@ -333,19 +333,19 @@ section at the end of this file).
  * };
  */
 
-#define USB_CFG_DESCR_PROPS_DEVICE                  0
-#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
+#define USB_CFG_DESCR_PROPS_DEVICE 0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
 //#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
-#define USB_CFG_DESCR_PROPS_STRINGS                 0
-#define USB_CFG_DESCR_PROPS_STRING_0                0
-#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
-#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
-#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
-#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
+#define USB_CFG_DESCR_PROPS_STRINGS 0
+#define USB_CFG_DESCR_PROPS_STRING_0 0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
+#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
 //#define USB_CFG_DESCR_PROPS_HID                     0
-#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
+#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
 //#define USB_CFG_DESCR_PROPS_HID_REPORT              0
-#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+#define USB_CFG_DESCR_PROPS_UNKNOWN 0
 
 #define usbMsgPtr_t unsigned short
 /* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
@@ -374,12 +374,10 @@ section at the end of this file).
 
 /* Set INT1 for D- falling edge to count SOF */
 /* #define USB_INTR_CFG            EICRA */
-#define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
+#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
 /* #define USB_INTR_CFG_CLR        0 */
 /* #define USB_INTR_ENABLE         EIMSK */
-#define USB_INTR_ENABLE_BIT     INT1
+#define USB_INTR_ENABLE_BIT INT1
 /* #define USB_INTR_PENDING        EIFR */
-#define USB_INTR_PENDING_BIT    INTF1
-#define USB_INTR_VECTOR         INT1_vect
-
-#endif /* __usbconfig_h_included__ */
+#define USB_INTR_PENDING_BIT INTF1
+#define USB_INTR_VECTOR INT1_vect