Cleanup rules.mk for 32U4 keyboards, N-Q (#7147)

3 files changed, 35 insertions, 160 deletions

diff --git a/keyboards/namecard2x4/rev1/rules.mk b/keyboards/namecard2x4/rev1/rules.mk
index 407298e900..e69de29bb2 100644
--- a/keyboards/namecard2x4/rev1/rules.mk
+++ b/keyboards/namecard2x4/rev1/rules.mk
@@ -1,80 +0,0 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Bootloader selection
-#   Teensy       halfkay
-#   Pro Micro    caterina
-#   Atmel DFU    atmel-dfu
-#   LUFA DFU     lufa-dfu
-#   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = yes        # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = no            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
-
-#UNICODEMAP_ENABLE = yes # for emoji user
-#RGBLIGHT_ENABLE = yes # uncomment if you want addressable led strips
diff --git a/keyboards/namecard2x4/rev2/rules.mk b/keyboards/namecard2x4/rev2/rules.mk
index 407298e900..e69de29bb2 100644
--- a/keyboards/namecard2x4/rev2/rules.mk
+++ b/keyboards/namecard2x4/rev2/rules.mk
@@ -1,80 +0,0 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Bootloader selection
-#   Teensy       halfkay
-#   Pro Micro    caterina
-#   Atmel DFU    atmel-dfu
-#   LUFA DFU     lufa-dfu
-#   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = yes        # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = no            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
-
-#UNICODEMAP_ENABLE = yes # for emoji user
-#RGBLIGHT_ENABLE = yes # uncomment if you want addressable led strips
diff --git a/keyboards/namecard2x4/rules.mk b/keyboards/namecard2x4/rules.mk
new file mode 100644
index 0000000000..d9eff798ce
--- /dev/null
+++ b/keyboards/namecard2x4/rules.mk
@@ -0,0 +1,35 @@
+# MCU name
+MCU = atmega32u4
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = atmel-dfu
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+#UNICODEMAP_ENABLE = yes # for emoji user
+#RGBLIGHT_ENABLE = yes # uncomment if you want addressable led strips