Merge remote-tracking branch 'upstream/master'

3 files changed, 13 insertions, 74 deletions

diff --git a/keyboards/mint60/keymaps/default/keymap.c b/keyboards/mint60/keymaps/default/keymap.c
index 4a90bd57c7..0c65f73c7e 100644
--- a/keyboards/mint60/keymaps/default/keymap.c
+++ b/keyboards/mint60/keymaps/default/keymap.c
@@ -19,7 +19,6 @@
 #include "split_util.h"
 #endif
 
-extern keymap_config_t keymap_config;
 
 #ifdef RGBLIGHT_ENABLE
 //Following line allows macro to read current RGB settings
@@ -52,22 +51,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 bool TOG_STATUS = false;
 int RGB_current_mode;
 
-
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-  // MACRODOWN only works in this function
-      switch(id) {
-        case 0:
-          if (record->event.pressed) {
-            register_code(KC_RSFT);
-          } else {
-            unregister_code(KC_RSFT);
-          }
-        break;
-      }
-    return MACRO_NONE;
-};
-
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
   switch (keycode) {
     case RGBRST:
diff --git a/keyboards/mint60/matrix.c b/keyboards/mint60/matrix.c
index 6d8878332a..30f3c56bcf 100644
--- a/keyboards/mint60/matrix.c
+++ b/keyboards/mint60/matrix.c
@@ -200,18 +200,12 @@ uint8_t matrix_scan(void)
     }else{
         matrix_slave_scan();
 
-//        if(serial_slave_DATA_CORRUPT()){
-//          TXLED0;
           int offset = (isLeftHand) ? ROWS_PER_HAND : 0;
 
           for (int i = 0; i < ROWS_PER_HAND; ++i) {
               matrix[offset+i] = serial_master_buffer[i];
           }
 
-//        }else{
-//          TXLED1;
-//        }
-
         matrix_scan_quantum();
     }
     return 1;
diff --git a/keyboards/mint60/rules.mk b/keyboards/mint60/rules.mk
index b4472153bc..037e814312 100644
--- a/keyboards/mint60/rules.mk
+++ b/keyboards/mint60/rules.mk
@@ -1,57 +1,15 @@
-SRC += i2c.c \
-	   serial.c \
-		 matrix.c \
- 	   split_util.c \
-
 # MCU name
-#MCU = at90usb1286
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = caterina
 
 # Build Options
 #   change yes to no to disable
@@ -74,5 +32,9 @@ FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 
 CUSTOM_MATRIX = yes
+SRC += i2c.c \
+       serial.c \
+       matrix.c \
+       split_util.c
 USE_I2C = yes
 RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.