[Keyboard] Refactor of onekey to support multiple development boards (#6017)

* Initial refactor of onekey to support multiple development boards

* Fixes to get teensy lc && 3.2 working

* Add pin tables

* Add caveats to Teensy boards

* Correct bootloader for Elite-C

1 files changed, 166 insertions, 0 deletions

diff --git a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h
new file mode 100644
index 0000000000..9427adabf1
--- /dev/null
+++ b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h
@@ -0,0 +1,166 @@
+/*
+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for a Generic STM32F103 board.
+ */
+
+/*
+ * Board identifier.
+ */
+#define BOARD_GENERIC_STM32_F103
+#define BOARD_NAME              "Generic STM32F103x board"
+
+/*
+ * Board frequencies.
+ */
+#define STM32_LSECLK            32768
+#define STM32_HSECLK            8000000
+
+/*
+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
+ */
+#define STM32F103xB
+
+/*
+ * IO pins assignments
+ */
+
+/* on-board */
+
+#define GPIOA_LED               8
+#define GPIOD_OSC_IN            0
+#define GPIOD_OSC_OUT           1
+
+/* In case your board has a "USB enable" hardware
+   controlled by a pin, define it here. (It could be just
+   a 1.5k resistor connected to D+ line.)
+*/
+/*
+#define GPIOB_USB_DISC          10
+*/
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ *
+ * The digits have the following meaning:
+ *   0 - Analog input.
+ *   1 - Push Pull output 10MHz.
+ *   2 - Push Pull output 2MHz.
+ *   3 - Push Pull output 50MHz.
+ *   4 - Digital input.
+ *   5 - Open Drain output 10MHz.
+ *   6 - Open Drain output 2MHz.
+ *   7 - Open Drain output 50MHz.
+ *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
+ *   9 - Alternate Push Pull output 10MHz.
+ *   A - Alternate Push Pull output 2MHz.
+ *   B - Alternate Push Pull output 50MHz.
+ *   C - Reserved.
+ *   D - Alternate Open Drain output 10MHz.
+ *   E - Alternate Open Drain output 2MHz.
+ *   F - Alternate Open Drain output 50MHz.
+ * Please refer to the STM32 Reference Manual for details.
+ */
+
+/*
+ * Port A setup.
+ * Everything input with pull-up except:
+ * PA2  - Alternate output  (USART2 TX).
+ * PA3  - Normal input      (USART2 RX).
+ * PA9  - Alternate output  (USART1 TX).
+ * PA10 - Normal input      (USART1 RX).
+ */
+#define VAL_GPIOACRL            0x88884B88      /*  PA7...PA0 */
+#define VAL_GPIOACRH            0x888884B8      /* PA15...PA8 */
+#define VAL_GPIOAODR            0xFFFFFFFF
+
+/*
+ * Port B setup.
+ * Everything input with pull-up except:
+ * PB10    - Push Pull output  (USB switch).
+ */
+#define VAL_GPIOBCRL            0x88888888      /*  PB7...PB0 */
+#define VAL_GPIOBCRH            0x88888388      /* PB15...PB8 */
+#define VAL_GPIOBODR            0xFFFFFFFF
+
+/*
+ * Port C setup.
+ * Everything input with pull-up except:
+ * PC13    - Push Pull output  (LED).
+ */
+#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */
+#define VAL_GPIOCCRH            0x88388888      /* PC15...PC8 */
+#define VAL_GPIOCODR            0xFFFFFFFF
+
+/*
+ * Port D setup.
+ * Everything input with pull-up except:
+ * PD0  - Normal input (XTAL).
+ * PD1  - Normal input (XTAL).
+ */
+#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */
+#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */
+#define VAL_GPIODODR            0xFFFFFFFF
+
+/*
+ * Port E setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */
+#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */
+#define VAL_GPIOEODR            0xFFFFFFFF
+
+/*
+ * USB bus activation macro, required by the USB driver.
+ */
+/* The point is that most of the generic STM32F103* boards
+   have a 1.5k resistor connected on one end to the D+ line
+   and on the other end to some pin. Or even a slightly more
+   complicated "USB enable" circuit, controlled by a pin.
+   That should go here.
+
+   However on some boards (e.g. one that I have), there's no
+   such hardware. In which case it's better to not do anything.
+*/
+/*
+#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)
+*/
+#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);
+
+/*
+ * USB bus de-activation macro, required by the USB driver.
+ */
+/*
+#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)
+*/
+#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+  void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */