Cleanup rules.mk for 32A and 328P keyboards (#6767)

1 files changed, 3 insertions, 55 deletions

diff --git a/keyboards/exclusive/e6v2/le_bmc/rules.mk b/keyboards/exclusive/e6v2/le_bmc/rules.mk
index a9156adeb5..13a5f1b89a 100644
--- a/keyboards/exclusive/e6v2/le_bmc/rules.mk
+++ b/keyboards/exclusive/e6v2/le_bmc/rules.mk
@@ -1,46 +1,5 @@
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
-
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 12000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-# ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-# F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS = -DDEBUG_LEVEL=0
-
 
 # Bootloader selection
 #   Teensy       halfkay
@@ -48,20 +7,10 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = bootloadHID
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #
@@ -84,6 +33,5 @@ AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 
+OPT_DEFS = -DDEBUG_LEVEL=0
 SRC += i2c_master.c
-
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex