Remove duplicate board files

1 files changed, 0 insertions, 166 deletions

diff --git a/keyboards/converter/siemens_tastatur/boards/GENERIC_STM32_F103/board.h b/keyboards/converter/siemens_tastatur/boards/GENERIC_STM32_F103/board.h
deleted file mode 100644
index 9427adabf1..0000000000
--- a/keyboards/converter/siemens_tastatur/boards/GENERIC_STM32_F103/board.h
+++ /dev/null
@@ -1,166 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-/*
- * Setup for a Generic STM32F103 board.
- */
-
-/*
- * Board identifier.
- */
-#define BOARD_GENERIC_STM32_F103
-#define BOARD_NAME              "Generic STM32F103x board"
-
-/*
- * Board frequencies.
- */
-#define STM32_LSECLK            32768
-#define STM32_HSECLK            8000000
-
-/*
- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
- */
-#define STM32F103xB
-
-/*
- * IO pins assignments
- */
-
-/* on-board */
-
-#define GPIOA_LED               8
-#define GPIOD_OSC_IN            0
-#define GPIOD_OSC_OUT           1
-
-/* In case your board has a "USB enable" hardware
-   controlled by a pin, define it here. (It could be just
-   a 1.5k resistor connected to D+ line.)
-*/
-/*
-#define GPIOB_USB_DISC          10
-*/
-
-/*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- *
- * The digits have the following meaning:
- *   0 - Analog input.
- *   1 - Push Pull output 10MHz.
- *   2 - Push Pull output 2MHz.
- *   3 - Push Pull output 50MHz.
- *   4 - Digital input.
- *   5 - Open Drain output 10MHz.
- *   6 - Open Drain output 2MHz.
- *   7 - Open Drain output 50MHz.
- *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
- *   9 - Alternate Push Pull output 10MHz.
- *   A - Alternate Push Pull output 2MHz.
- *   B - Alternate Push Pull output 50MHz.
- *   C - Reserved.
- *   D - Alternate Open Drain output 10MHz.
- *   E - Alternate Open Drain output 2MHz.
- *   F - Alternate Open Drain output 50MHz.
- * Please refer to the STM32 Reference Manual for details.
- */
-
-/*
- * Port A setup.
- * Everything input with pull-up except:
- * PA2  - Alternate output  (USART2 TX).
- * PA3  - Normal input      (USART2 RX).
- * PA9  - Alternate output  (USART1 TX).
- * PA10 - Normal input      (USART1 RX).
- */
-#define VAL_GPIOACRL            0x88884B88      /*  PA7...PA0 */
-#define VAL_GPIOACRH            0x888884B8      /* PA15...PA8 */
-#define VAL_GPIOAODR            0xFFFFFFFF
-
-/*
- * Port B setup.
- * Everything input with pull-up except:
- * PB10    - Push Pull output  (USB switch).
- */
-#define VAL_GPIOBCRL            0x88888888      /*  PB7...PB0 */
-#define VAL_GPIOBCRH            0x88888388      /* PB15...PB8 */
-#define VAL_GPIOBODR            0xFFFFFFFF
-
-/*
- * Port C setup.
- * Everything input with pull-up except:
- * PC13    - Push Pull output  (LED).
- */
-#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */
-#define VAL_GPIOCCRH            0x88388888      /* PC15...PC8 */
-#define VAL_GPIOCODR            0xFFFFFFFF
-
-/*
- * Port D setup.
- * Everything input with pull-up except:
- * PD0  - Normal input (XTAL).
- * PD1  - Normal input (XTAL).
- */
-#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */
-#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */
-#define VAL_GPIODODR            0xFFFFFFFF
-
-/*
- * Port E setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */
-#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */
-#define VAL_GPIOEODR            0xFFFFFFFF
-
-/*
- * USB bus activation macro, required by the USB driver.
- */
-/* The point is that most of the generic STM32F103* boards
-   have a 1.5k resistor connected on one end to the D+ line
-   and on the other end to some pin. Or even a slightly more
-   complicated "USB enable" circuit, controlled by a pin.
-   That should go here.
-
-   However on some boards (e.g. one that I have), there's no
-   such hardware. In which case it's better to not do anything.
-*/
-/*
-#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)
-*/
-#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);
-
-/*
- * USB bus de-activation macro, required by the USB driver.
- */
-/*
-#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)
-*/
-#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
-  void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif /* _FROM_ASM_ */
-
-#endif /* _BOARD_H_ */