Add protocol/lufa. LUFA supported now.

5 files changed, 220 insertions, 57 deletions

diff --git a/keyboard/macway/Makefile b/keyboard/macway/Makefile
deleted file mode 100644
index afee38b120..0000000000
--- a/keyboard/macway/Makefile
+++ /dev/null
@@ -1,53 +0,0 @@
-# Target file name (without extension).
-TARGET = macway
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC =	main.c \
-	keymap.c \
-	matrix.c \
-	led.c
-
-CONFIG_H = config.h
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
-
-
-# Build Options
-#   comment out to disable the options.
-#
-MOUSEKEY_ENABLE = yes	# Mouse keys
-#PS2_MOUSE_ENABLE = yes	# PS/2 mouse(TrackPoint) support
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-#NKRO_ENABLE = yes	# USB Nkey Rollover
-
-
-
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-
-
-
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
diff --git a/keyboard/macway/Makefile.lufa b/keyboard/macway/Makefile.lufa
new file mode 100644
index 0000000000..a3395a2ab7
--- /dev/null
+++ b/keyboard/macway/Makefile.lufa
@@ -0,0 +1,114 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = macway_lufa
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+
+# List C source files here. (C dependencies are automatically generated.)
+SRC +=	keymap.c \
+	matrix.c \
+	led.c \
+	protocol/pjrc/bootloader_teensy.c
+
+CONFIG_H = config.h
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+
+# Build Options
+#   comment out to disable the options.
+#
+MOUSEKEY_ENABLE = yes	# Mouse keys
+#PS2_MOUSE_ENABLE = yes	# PS/2 mouse(TrackPoint) support
+EXTRAKEY_ENABLE = yes	# Audio control and System control
+#NKRO_ENABLE = yes	# USB Nkey Rollover
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
diff --git a/keyboard/macway/Makefile.pjrc b/keyboard/macway/Makefile.pjrc
new file mode 100644
index 0000000000..d2fb8ff2f6
--- /dev/null
+++ b/keyboard/macway/Makefile.pjrc
@@ -0,0 +1,96 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = macway_pjrc
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC =	protocol/pjrc/main.c \
+	keymap.c \
+	matrix.c \
+	led.c
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162       # Teensy 1.0
+MCU = atmega32u4       # Teensy 2.0
+#MCU = at90usb646       # Teensy++ 1.0
+#MCU = at90usb1286      # Teensy++ 2.0
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 16000000
+
+
+# Build Options
+#   comment out to disable the options.
+#
+MOUSEKEY_ENABLE = yes	# Mouse keys
+#PS2_MOUSE_ENABLE = yes	# PS/2 mouse(TrackPoint) support
+EXTRAKEY_ENABLE = yes	# Audio control and System control
+#NKRO_ENABLE = yes	# USB Nkey Rollover
+
+
+
+#---------------- Programming Options --------------------------
+PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/pjrc.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
diff --git a/keyboard/macway/config.h b/keyboard/macway/config.h
index b68ea20dcf..5503c77e3a 100644
--- a/keyboard/macway/config.h
+++ b/keyboard/macway/config.h
@@ -21,10 +21,16 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* controller configuration */
 #include "controller_teensy.h"
 
+
+/* USB Device descriptor parameter */
 #define VENDOR_ID       0xFEED
 #define PRODUCT_ID      0xBEE0
+#define DEVICE_VER      0x0202
 #define MANUFACTURER    t.m.k.
 #define PRODUCT         Macway mod
+
+
+/* message strings */
 #define DESCRIPTION     t.m.k. keyboard firmware for Macway mod
 
 
diff --git a/keyboard/macway/keymap.c b/keyboard/macway/keymap.c
index 89634e2f41..5ecea2569f 100644
--- a/keyboard/macway/keymap.c
+++ b/keyboard/macway/keymap.c
@@ -59,7 +59,7 @@ static const uint8_t PROGMEM fn_layer[] = {
     3,              // Fn3
     4,              // Fn4
     0,              // Fn5
-    2,              // Fn6
+    3,              // Fn6
     3               // Fn7
 };
 
@@ -94,7 +94,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
            TAB, Q,   W,   E,   R,   T,   Y,   U,   I,   O,   P,   LBRC,RBRC,BSLS, \
            LCTL,A,   S,   D,   F,   G,   H,   J,   K,   L,   FN3, QUOT,ENT, \
            LSFT,Z,   X,   C,   V,   B,   N,   M,   COMM,DOT, FN2, RSFT,FN1, \
-           FN7, LGUI,LALT,FN4, RALT,BSLS,GRV, FN6, RCTL),
+           FN7, LGUI,LALT,FN4, RALT,GRV, FN6, FN6, RCTL),
 
 
     /* Layer 1: HHKB mode (HHKB Fn)
@@ -110,7 +110,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
      * |   |Gui |Alt  |                      |Alt  |Gui|   |   |Ctr|
      * `-----------------------------------------------------------'
      */ 
-    KEYMAP(ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, DEL, \
+    KEYMAP(PWR, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, DEL, \
            CAPS,NO,  NO,  NO,  NO,  NO,  NO,  NO,  PSCR,SLCK,BRK, UP,  NO,  NO,  \
            LCTL,VOLD,VOLU,MUTE,NO,  NO,  PAST,PSLS,HOME,PGUP,LEFT,RGHT,ENT, \
            LSFT,NO,  NO,  NO,  NO,  NO,  PPLS,PMNS,END, PGDN,DOWN,RSFT,FN1, \
@@ -155,7 +155,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
            BSLS,WH_L,WH_D,MS_U,WH_U,WH_R,WH_L,WH_D,WH_U,WH_R,NO,  NO,  NO,  NO,  \
            LCTL,NO,  MS_L,MS_D,MS_R,NO,  MS_L,MS_D,MS_U,MS_R,FN3, NO,  BSLS, \
            LSFT,NO,  NO,  BTN1,BTN2,BTN3,BTN2,BTN1,NO,  NO,  NO,  RSFT,NO, \
-           FN7, LGUI,LALT,BTN1,RALT,NO,  NO,  NO,  NO),
+           FN7, LGUI,LALT,BTN1,RALT,NO,  FN6, FN6, NO),
 
 
     /* Layer 4: Matias half keyboard style (Space)