Re-fix the STM32 dual-bank bootloader stuff. (#9738)

* Re-fix the dual-bank bootloader stuff.

* Use wait_ms() instead of using nop's for a delay, as ChibiOS is actually running at the time of bootloader jump.

1 files changed, 15 insertions, 31 deletions

diff --git a/tmk_core/common/chibios/bootloader.c b/tmk_core/common/chibios/bootloader.c
index dceeaa6b19..743448ee18 100644
--- a/tmk_core/common/chibios/bootloader.c
+++ b/tmk_core/common/chibios/bootloader.c
@@ -2,6 +2,7 @@
 
 #include "ch.h"
 #include "hal.h"
+#include "wait.h"
 
 /* This code should be checked whether it runs correctly on platforms */
 #define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
@@ -31,45 +32,28 @@
 
 extern uint32_t __ram0_end__;
 
-#    define bootdelay(loopcount)                  \
-        do {                                      \
-            for (int i = 0; i < loopcount; ++i) { \
-                __asm__ volatile("nop\n\t"        \
-                                 "nop\n\t"        \
-                                 "nop\n\t");      \
-            }                                     \
-        } while (0)
-
 void bootloader_jump(void) {
-    *MAGIC_ADDR = BOOTLOADER_MAGIC;  // set magic flag => reset handler will jump into boot loader
-    NVIC_SystemReset();
-}
-
-void enter_bootloader_mode_if_requested(void) {
-    unsigned long *check = MAGIC_ADDR;
-    if (*check == BOOTLOADER_MAGIC) {
-        *check = 0;
-
-        // For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
-        // bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
-        // it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
-        // BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
-        // #hardware channel pins for an example circuit.
-        palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
+    // For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
+    // bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
+    // it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
+    // BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
+    // #hardware channel pins for an example circuit.
+    palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
 #    if STM32_BOOTLOADER_DUAL_BANK_POLARITY
-        palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
+    palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
 #    else
-        palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
+    palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
 #    endif
 
-        // Wait for a while for the capacitor to charge
-        bootdelay(STM32_BOOTLOADER_DUAL_BANK_DELAY);
+    // Wait for a while for the capacitor to charge
+    wait_ms(100);
 
-        // Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
-        NVIC_SystemReset();
-    }
+    // Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
+    NVIC_SystemReset();
 }
 
+void enter_bootloader_mode_if_requested(void) {}  // not needed at all, but if anybody attempts to invoke it....
+
 #elif defined(STM32_BOOTLOADER_ADDRESS)  // STM32_BOOTLOADER_DUAL_BANK
 
 extern uint32_t __ram0_end__;