| Age | Commit message (Collapse) | Author |
|---|
|
|
|
* Make solo half of split keyboards (more) usable.
Using only one half of a split keyboard (that's using the split_common
framework to communicate) is not a great experience, since several read
timeouts per scan cycle cause an unusably slow scan rate.
This change blocks all split communication attempts for 500 ms
(configurable) after an error occurs, causing the scan rate to become at
least _more_ usable, but might need some tweaking to work fully on most
keyboards. One read timeout still needs to occur after the 500 ms has
passed, and if that timeout isn't low enough, some scan cycles may still
be too slow.
* Fix lint complaint.
* Require 25 consecutive comm errors to see comms as disconnected.
The number of max errors can be overridden by defining
`SPLIT_MAX_CONNECTION_ERRORS`.
* Add comments to new defines, and ability to disable disconnection check.
Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible
by most relevant numbers for the description.
* Make lint happy ...again
* Only update `connection_check_timer` when needed.
* Add new defines to split keyboard documentation.
* Move connection timeout logic to transport.c, add `is_transport_connected`.
* Use split_common disconnection logic in matrix.c.
Instead of doing more or less the same thing twice.
* Move disconnection logic to `transport_master`.
Is a cleaner implementation, and causes the scan rate while disconnected
to increase instead of decrease.
* Lint fixes.
* Lower default `SERIAL_USART_TIMEOUT` to 20 ms.
The read timeout must be low enough to not cause exessively long scan
cycles when using a solo split half. 10 ms was determined from testing
to work fine even with the slowest defined baudrate of 19200 (5 ms was
too low for that case), so 20 ms should be fine for most cases.
* Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h
Was somewhat mistakenly included in an earlier PR.
* Fix building with `USE_I2C`.
* Reduce built firmware size.
Not really sure why this works, the idea was taken from tzarc's work on
split disconnection.
* Tweak and improve opt-out for split disconnection logic.
There are now two ways to opt out from this feature:
* Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable
the connection status checks (also affects the slave matrix reset logic in
matrix.c, though).
* Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the
communication throttling while disconnected. Will make the firmware
smaller.
* Make split disconnection logic work with custom transports.
Includes a fallback implementation for keyboards using a custom
split_util.c but not a custom matrix.c (currently no such keyboard seems
to be merged, though).
* Remove unnecessary include of timer.h
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
|
|
* Extensible split data sync capability through transactions.
- Split common transport has been split up between the transport layer
and data layer.
- Split "transactions" model used, with convergence between I2C and
serial data definitions.
- Slave matrix "generation count" is used to determine if the full slave
matrix needs to be retrieved.
- Encoders get the same "generation count" treatment.
- All other blocks of data are synchronised when a change is detected.
- All transmissions have a globally-configurable deadline before a
transmission is forced (`FORCED_SYNC_THROTTLE_MS`, default 100ms).
- Added atomicity for all core-synced data, preventing partial updates
- Added retries to AVR i2c_master's i2c_start, to minimise the number of
failed transactions when interrupts are disabled on the slave due to
atomicity checks.
- Some keyboards have had slight modifications made in order to ensure
that they still build due to firmware size restrictions.
* Fixup LED_MATRIX compile.
* Parameterise ERROR_DISCONNECT_COUNT.
|
|
|
|
|
|
Co-authored-by: QMK Bot <hello@qmk.fm>
|
|
|
|
Co-authored-by: QMK Bot <hello@qmk.fm>
|
|
|
|
Co-authored-by: QMK Bot <hello@qmk.fm>
|
|
* Split RGB Matrix
* Suspend State sync for rgb matrix
|
|
Co-authored-by: QMK Bot <hello@qmk.fm>
|
|
* Split transport mirror support
* Updated RGB Matrix to respond to electrical events instead of key events
* split matrix slave fix
|
|
|
|
|
|
* Add modifier state to the split transport
This adds modifier state to the i2c and serial transport for split
keyboards. The purpose of this is to allow e.g. displaying modifier
state on the slave side of a split keyboard on an oled. This adds one
byte to the data transferred between halves.
This also fixes a missing ifdef guard for BLACKLIGHT_ENABLE.
Break modifiers into real/weak/oneshot
Fix incorrect slave serial mod setting
Fix typo in serial weal mod setter
Fix build errors for the I2C code that I introduced
Code cleanup and formatting per project preferences
Correctly get oneshot mods
Fix missing braces
Remove unneeded ifdef guard
Make the added state transport optional
Add documentation for the new define to enable this feature
Fix stray grave mark
* Fix error introduced in conflict resolution
|
|
A timer that is kept in sync between the halves of a split keyboard
|
|
|
|
* Add Word Per Minute calculation feature
* Fix copyright info
* Remove header from quantum.c, setup overloadable keycode inclusion for WPM, update docs
* Simplify logic for keycode filtering
* Adding link from summary to wpm_feature info
* Update docs/feature_wpm.md
Typo in function prototype example in docs
Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com>
* Add WPM transport via i2c
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
|
|
Its use in lets_split_eh was factored out in https://github.com/qmk/qmk_firmware/pull/6411
|
|
|
|
* Remove the need to set NUM_OF_ENCODERS
Instead, calculate the size of the array, and use that instead
* Add hack for split common support
* Remove NUM_OF_ENCODERS from keyboard config
Can be reverted, if needed
|
|
|
|
slave backlight was always on - as get_backlight_level() doesn't
indicate if the backlight is enabled or not.
also updated the corosponding code for serial transport to stop peeking
directly at 'internal' backlight_config structure.
|
|
* add I2C_slave_buffer_t to quantum/split_common/transport.c
Improvements to ease the maintenance of the I2C slave buffer layout. And this commit does not change the compilation results.
* add temporary pdhelix(Patched Helix) code
* temporary cherry-pick from #5020
add new version(#5020) quantum/rgblight.[ch], quantum/rgblight_modes.h
* add post_config.h support to build_keyboard.mk
* add quantum/rgblight_post_config.h, quantum/split_common/post_config.h
Add quantum/rgblight_post_config.h and quantum/split_common/post_config.h using POST_CONFIG_H variable of build_keyboard.mk.
quantum/rgblight_post_config.h additionally defines RGBLIGHT_SPLIT if RGBLED_SPIT is defined.
quantum/split_common/post_config.h defines RGBLIGHT_SPLIT additionally when master-slave communication is I2C.
* Change split_common's transport.c I2C to use the synchronization feature of rgblight.c
* Change split_common's transport.c serial to use the synchronization feature of rgblight.c
* test RGBLIGHT_SPLIT on keyboards/handwired/pdhelix
* Test End Revert "test RGBLIGHT_SPLIT on keyboards/handwired/pdhelix"
This reverts commit 80118a6bbd3d9fc4c7797fef0c34bc67aa73aa98.
[x] make RGBLIGHT_TEST=1 handwired/pdhelix/i2c:default
[x] make RGBLIGHT_TEST=2 handwired/pdhelix/i2c:default (same RGBLIGHT_TEST=3)
[x] make RGBLIGHT_TEST=3 handwired/pdhelix/i2c:default
[x] make RGBLIGHT_TEST=1 handwired/pdhelix/pd2:default
[x] make RGBLIGHT_TEST=2 handwired/pdhelix/pd2:default
[x] make RGBLIGHT_TEST=3 handwired/pdhelix/pd2:default
[x] make RGBLIGHT_TEST=1 handwired/pdhelix/pd2_2oled:default
[x] make RGBLIGHT_TEST=2 handwired/pdhelix/pd2_2oled:default
[x] make RGBLIGHT_TEST=3 handwired/pdhelix/pd2_2oled:default
* Test End, Revert "temporary cherry-pick from #5020"
This reverts commit d35069f68bda0c50370442a5c7aae60c2f4ce5c0.
* Test End, Revert "add temporary pdhelix(Patched Helix) code"
This reverts commit aebddfc1a879796afae297ef0723a4fe73af3660.
* temporarily cherry-pick from #5020 to see if it passes the travis-ci test.
add new version(#5020) quantum/rgblight.[ch], quantum/rgblight_modes.h
* Passed the travis-ci test. Revert "temporarily cherry-pick from #5020 to see if it passes the travis-ci test."
This reverts commit 647c0a9755eb6a05f76d09b2d59bce67b85a841f.
* update docs/config_options.md
* update split_common/transport.c, improves maintainability of serial transaction IDs.
No change in build result.
* temporary cherry-pick from #5020
* fix build fail keebio/iris/rev3:default
* fix build fail lets_split_eh/eh:default
* Revert "temporary cherry-pick from #5020"
This reverts commit be48ca1b4515366a097af8dd1cd7b28b7ee09947.
* temporary cherry-pick from #5020 (0.6.336)
* Revert "temporary cherry-pick from #5020 (0.6.336)"
This reverts commit 978d26a8b3cf0acc485838a7d76d6128b77c630c.
* temporary cherry-pick from #5020 (0.6.336)
|
|
* Added slave encoder support to split common
* Fixing handwired/xealous/rev1 compile error
* Removed unnecessary ifdef
|
|
* Add support for wiring RGB LEDs for both halves directly to their respective controllers
RGB LEDs for each half don't need to be chained together across the TRRS cable with this
* Add split RGB LED support for serial
* Update config/rules for bakingpy layout
* Un-nest ifdefs for hand detection
* Read RGB config state from memory instead of EEPROM for serial updates
* Reuse existing LED pointer instead of creating new one
|
|
|
|
* Make rgblight_update_dword not update eeprom (we already have
eeconfig_update_rgblight for that).
Make split i2c keyboards transfer active rgblight config rather than
eeprom saved version of rgblight config, enabling runtime changes
that aren't persisted to eeprom.
* prev_level and prev_rgb only store successfully transmitted values
|
|
* Update split_common to use standard i2c drivers
* Eliminate RGB_DIRTY/BACKLIT_DIRTY
* Fix avr i2c_master error handling
* Fix i2c_slave addressing
* Remove unneeded timeout on i2c_stop()
* Fix RGB I2C transfers
* Remove incorrect comment
|
|
* Eliminate separate slave loop
Both master and slave run the standard keyboard_task main loop now.
* Refactor i2c/serial specific code
Simplify some of the preprocessor mess by using common function names.
* Fix missing #endif
* Move direct pin mapping support from miniaxe to split_common
For boards with more pins than sense--sorry, switches.
* Reordering and reformatting only
* Don't run matrix_scan_quantum on slave side
* Clean up the offset/slaveOffset calculations
* Cut undebounced matrix size in half
* Refactor debouncing
* Minor fixups
* Split split_common transport and debounce code into their own files
Can now be replaced with custom versions per keyboard using
CUSTOM_TRANSPORT = yes and CUSTOM_DEBOUNCE = yes
* Refactor debounce for non-split keyboards too
* Update handwired/xealous to build using new split_common
* Fix debounce breaking basic test
* Dodgy method to allow a split kb to only include one of i2c/serial
SPLIT_TRANSPORT = serial or SPLIT_TRANSPORT = i2c will include only
that driver code in the binary.
SPLIT_TRANSPORT = custom (or anything else) will include neither, the
keyboard must supply it's own code
if SPLIT_TRANSPORT is not defined then the original behaviour (include
both avr i2c and serial code) is maintained.
This could be better but it would require explicitly updating all the
existing split keyboards.
* Enable LTO to get lets_split/sockets under the line
* Add docs for SPLIT_TRANSPORT, CUSTOM_MATRIX, CUSTOM_DEBOUNCE
* Remove avr-specific sei() from split matrix_setup
Not needed now that slave doesn't have a separate main loop.
Both sides (on avr) call sei() in lufa's main() after exiting
keyboard_setup().
* Fix QUANTUM_LIB_SRC references and simplify SPLIT_TRANSPORT.
* Add comments and fix formatting.
|
