Age | Commit message (Collapse) | Author |
|
|
|
* helix/serial.c add support PD1,PD3,PE6 and configuration simplify
* Add comment about ATmega32U4 I2C
* Add compile time check for ATmega32U4 I2C
* change TAB code to 8 SPACE code
* Helix serial.c PORTD,PD0 test. OK
OK PD0
- PD1
OK PD2
- PD3
- PE6
* Helix serial.c PORTD,PD1 test. OK
OK PD0
OK PD1
OK PD2
- PD3
- PE6
* Helix serial.c PORTD,PD3 test. OK
OK PD0
OK PD1
OK PD2
OK PD3
- PE6
* Helix serial.c PORTE,PD6 test. OK
OK PD0
OK PD1
OK PD2
OK PD3
OK PE6
* Helix serial.c: PD0,PD1,PD3,PE6 all test end
* Helix serial.c: rename SOFT_SERIAL_PORT to SOFT_SERIAL_PIN
* Helix serial.c add debug code
* Helix serial.c: add transaction ID range check
* Helix serial.c debug code update
* Helix serial.c debug code update
* Helix serial.c: Strict checking of the value of tid.
* adjust the delay of serial.c
* Helix serial.c: remove debug code
* remove EXTRAFLAGS += -DCONSOLE_ENABLE from five_rows/rules.mk
tmk_core/common.mk has
>ifeq ($(strip $(CONSOLE_ENABLE)), yes)
> TMK_COMMON_DEFS += -DCONSOLE_ENABLE
* Fix error handling in split_scomm.c
* add some comment to serial.c
* add some comment about SELECT_SOFT_SERIAL_SPEED
|
|
* add PERMISSIVE_HOLD in helix:five_rows/config.h
* add Eucalyn char layout into helix:five_rows
* Helix five_rows keymap: make rgblight modes selectable.
No change in build result.
* fix keymap.c map comment, add console compile option
No change in build result.
* Helix five_rows keymap: reduced the size.
|
|
* add change_reciver2sender()/change_sender2reciver()
This is a change to improve readability.
* txled, rxled off in matrix_init()
* add serial_send_packet() / serial_recive_packet()
This is a change to reduce object size.
* add serial_low() at ISR() top
* add __attribute__((always_inline)) to some functions
* modify serial_send_packet()/serial_recive_packet()
A little, object size reduction.
A little, speedup.
* add debug code to helix/serial.c
* Adjust sampling timing of serial signal being received
* add split_scomm.c/split_scomm.h and change serial.c/serial.h
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
* add split_scomm.c/split_scomm.h into helix/rev1
* reduce object size helix/rev2/matrix.c
* remove checksum check, add parity check
* force occur parity error for test
* parity test ok. remove test code
* change some comment & add skip code when buffer_size == 0
* serial.c: multiple types of transaction support
Add 4 bits transaction-type field at packet top.
Select Transaction Descriptor Table entry by transaction-type.
* helix serial master-slave transaction optimize
Using multi-type transaction feature of serial.c, communication contents between master slaves were optimized.
* add debug code for retry
* add comment into each config.h
* fix ISR status drop
* add a debug macro 'debug_retry_chg()'
* reduce led_test size
* remove debug code from helix/serial.c and etc.
* helix:five_rows change TAPPING_TERM value 140
* Improved compatibility with let's split of serial.c. Finish helix/serial.c improvement.
- The difference with the original let's split's serial.c
- It's high-speed about 4 times.
- Stable bi-directional data transfer. (Helix need master to slave transfer)
- serial.h was divided 2 files, serial_config.h and sereial.h
- With multiple types of transaction support, communication contents can be optimized. (NEW flexible API)
- USE OLD Simple APIs (compatible with let's split serial.c)
- files :
- serial_config.h -- hardware configuration (need include by config.h)
- serial.c/serial.h -- serial communication
- USE NEW flexible APIs. (Support multi-type transaction function.)
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
- files
- split_scomm.c -- communication buffer is defined in here. call by matrix.c.
- split_scomm.h -- buffer size is defined in here. include by matrix.c, split_util.c
- serial_config.h -- hardware configuration (need include by config.h)
To use the NEW API, specify #define SERIAL_USE_MULTI_TRANSACTION
- serial.c/serial.h -- serial communication lower layer
- NEW APIs for serial.c / serial.h (The lower layer)
// Soft Serial Transaction Descriptor
typedef struct _SSTD_t {
uint8_t *status;
uint8_t initiator2target_buffer_size;
uint8_t *initiator2target_buffer;
uint8_t target2initiator_buffer_size;
uint8_t *target2initiator_buffer;
} SSTD_t;
// initiator is transaction start side
void soft_serial_initiator_init(SSTD_t *sstd_table);
// target is interrupt accept side
void soft_serial_target_init(SSTD_t *sstd_table);
int soft_serial_transaction(int sstd_index);
int soft_serial_get_and_clean_target_status(int sstd_index);
- NEW APIs for split_scomm.c / split_scomm.h (The upper layer)
move from old serial.c the following buffer and functions
serial_slave_buffer[]
serial_master_buffer[]
void serial_master_init(void)
void serial_slave_init(void)
int serial_update_buffers(void)
define SERIAL_xxxxx_BUFFER_LENGTH move from serial_config.h to split_scomm.h
|
|
Underglow (#3546)
* build break fix for HelixPico
* add customize variable 'Link_Time_Optimization' into rev2 and pico keymaps rules.mk
* "CFLAGS += -flto" change to "EXTRAFLAGS += -flto"
* add USE_Link_Time_Optimization macro
|
|
* helix config.h refine
|
|
* add some comment about Helix customize and auto-setup RGBLIGHT_LIMIT_VAL
* add define USB_MAX_POWER_CONSUMPTION
* Helix keyboard OLED, RGBLIGHT enable/disable control integrate into rules.mk
rules.mk: add 4 Variables for compile control.
# Helix keyboard customize
# you can edit follows 4 Variables
# jp: 以下の4つの変数を必要に応じて編集します。
OLED_ENABLE = no # OLED_ENABLE
LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.)
LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
config.h: auto set RGBLED_NUM by HELIX_ROWS and rules.mk's define
* HELIX_ROWS define move from config.h to rules.mk
* add readme.md
* rename readme.md to readme_jp.md
* add readme.md and modify readme_jp.md
* change helix/ssd1306.c for select glcdfont.c position
* add variable LOCAL_GLCDFONT into each keymaps rules.mk
* Add iPhone/iPad LED support to Helix default keymap
* renumber _ADJUST for shrink program size
* Fix Helix i2c wrong bit rate
* add helix serial debug code
* serial debug macro move from config.h to serial.h
* helix serial.c debugging...
* refine debug macros
* add some comments
* add SELECT_SERIAL_SPEED
* add comments
* debugging sync_send/sync_recv
* add very high speed
* fix sync_send/sync_recv
* fix com. start and switch send/recv
* debug mode off
* remove debug codes
* Shrinked config.h
|
|
* Matrix refactor
* Keymap refactor
* Configurator support
|
|
|
|
* add some comment about Helix customize and auto-setup RGBLIGHT_LIMIT_VAL
* add define USB_MAX_POWER_CONSUMPTION
* Helix keyboard OLED, RGBLIGHT enable/disable control integrate into rules.mk
rules.mk: add 4 Variables for compile control.
# Helix keyboard customize
# you can edit follows 4 Variables
# jp: 以下の4つの変数を必要に応じて編集します。
OLED_ENABLE = no # OLED_ENABLE
LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.)
LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
config.h: auto set RGBLED_NUM by HELIX_ROWS and rules.mk's define
* HELIX_ROWS define move from config.h to rules.mk
* add readme.md
* rename readme.md to readme_jp.md
* add readme.md and modify readme_jp.md
* change helix/ssd1306.c for select glcdfont.c position
* add variable LOCAL_GLCDFONT into each keymaps rules.mk
|
|
* add 'HELIX=' option for build
* add IOS_DEVICE_ENABLE for iPad
* shrink size to helix five_rows keymap.c
* shrink size. _ADJUST number change
* add KEYPAD layer
* modify keypad leyer
* display RGB mode on slave side OLED
* fix Colemak, Dvorak center DEL to BS
* change LEFT BS to LEFT SP and add AUX layer for try old map
* update update_base_layer()
* add right keypad and keypad func layer
* use MO() macro insted of LOWER,RAISE,ADJUST custom key-code
* remove LOWER,RAISE,ADJUST custom key-code
* use MO(_LOWER|_RAISE|_ADJUST)
* relayout ADJUST layer
* modify Function Layer. PGUP,PGDN swap HOME,END
* add Keypad aux layer for '00' send
* update README.md, README_jp.md
* fix README.md
* fix README.md, README_jp.md
|
|
* duplicate keyboards/helix/rev2/keymaps/default to keyboards/helix/rev2/keymaps/five_rows
* OLED Layer display 'Qwerty','Colemak','Dvorak'
* set Qwerty, Lower, Raise map
* set Colemak map
* set Dvorak map
* OLED Layer display 'Raise','Lower' change to 'Extra char','Function'
* fix ExtraChar Layer Shift-key disable
* Raise,Lower,Adjust layer modify
some key change KC_TRNS to KC_NO
add KANA, EISU key
* refine keymaps/five_rows/{config.h,rules.mk} for easy and safe customize
* modify Adjust layer: all function into left hand, remove F1..F12,DEL
* Add Helix five_rows keymap README.md and README_jp.md
* Raise Layer modify: enable Raise(Extr)+Lower(Func)==Adjust
* fix image file url in README.md,README_jp.md
* change Layer display on OLED
* change OLED display base name position
|