Age | Commit message (Collapse) | Author |
|
|
|
|
|
|
|
* Use polled waiting on platforms that support it
Due to context switching overhead waiting a very short amount of time on
a sleeping thread is often not accurate and in fact not usable for timing
critical usage i.e. in a driver. Thus we use polled waiting for ranges
in the us range on platforms that support it instead. The fallback is
the thread sleeping mechanism.
This includes:
* ARM platforms with CYCCNT register (ARMv7, ARMv8) this is
incremented at CPU clock frequency
* GD32VF103 RISC-V port with CSR_MCYCLE register this is incremented at
CPU clock frequency
* RP2040 ARMv6 port which uses the integrated timer peripheral which is
incremented with a fixed 1MHz frequency
* Use wait_us() instead of chSysPolledDelayX
...as it is powered by busy waiting now.
* Add chibios waiting methods test bench
|
|
* Tentative Teensy 3.5 support
* Set firmware format to .hex for ARM Teensys
* Got to "device descriptor failed" by comparing with Teensy 3.6 code
* Drop down to 96MHz...
* Bump back up to 120MHz
|
|
|
|
|
|
* Disable RESET keycode because of naming conflicts
* Add Pico SDK as submodule
* Add RP2040 build support to QMK
* Adjust USB endpoint structs for RP2040
* Add RP2040 bootloader and double-tap reset routine
* Add generic and pro micro RP2040 boards
* Add RP2040 onekey keyboard
* Add WS2812 PIO DMA enabled driver and documentation
Supports regular and open-drain output configuration. RP2040 GPIOs are
sadly not 5V tolerant, so this is a bit use-less or needs extra hardware
or you take the risk to fry your hardware.
* Adjust SIO Driver for RP2040
* Adjust I2C Driver for RP2040
* Adjust SPI Driver for RP2040
* Add PIO serial driver and documentation
* Add general RP2040 documentation
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
|
|
|
|
|
|
engine (#15657)
|
|
|
|
|
|
|
|
* Add non blackpill F4x1 config files
* Move ld files
* Remove f401 i2c bodges
* more bodge?
* Update to recommended defaults
|
|
* Joystick feature updates
* Move new functions to joystick.h
* Docs
|
|
(#16655)
|
|
|
|
|
|
|
|
* Refactor `bootloader_jump()` implementations
* Fix tests?
* Rename `atmel-samba` to `md-boot`
|
|
|
|
|
|
* [Core] Add kb level callbacks to OLED driver
* Update keyboards and keymaps
* Update docs
* Update userspace configs
* Add fix for my keymap ...
* update lefty
|
|
* Add support for RISC-V builds and GD32VF103 MCU
* Add toolchain selection in chibios.mk based on the mcu selected in
mcu_selection.mk
* Reorder and added comments to chibios.mk to have a streamlined makefile
* Add GD32VF103 mcu to possible targets for QMK.
* Add STM32 compatibility for GD32VF103 MCU, this is hacky but more efficent
then rewriting every driver.
* Add GigaDevice DFU bootloader as flash target, please note that
dfu-util of at least version 0.10 is needed.
* Add analog driver compatibility
* Add apa102 bitbang driver compatibility
* Add ws2812 bitbang driver compatibility
* Add eeprom in flash emulation compatibility
* Allow faster re-builds with ccache
* Add SiPeed Longan Nano to platform files
* Add SiPeed Longan Nano Onekeys
* Make quine compatible with other bootloaders
* Support builds with picolibc
* Add risc-v toolchain to arch and debian/ubuntu scripts
|
|
* Initial pass of F405 support
* remove some conf files
* docs
* clang
|
|
* Align ChibiOS I2C defs with other drivers
* Update keyboards/xelus/valor_frl_tkl/config.h
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
|
|
|
|
|
|
|
|
|
|
* add docs
* core changes
* update keyboards to new OLED
* updated users to new OLED
* update layouts to new OLED
* fixup docs
* drashna's suggestion
* fix up docs
* new keyboards with oled
* core split changes
* remaining keyboard files
* Fix The Helix keyboards oled options
* reflect develop
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: mtei <2170248+mtei@users.noreply.github.com>
|
|
* Add digitizer HID interface for setting the mouse cursor position at
absolute screen coordinates. Tested on Pro Micro, Proton C and
Blackpill.
* Update docs/feature_digitizer.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add missing copyrights
Add V-USB support
* Add support for digitizer dedicated endpoint for lufa and chibios.
Fix formatting issues
Move digitizer_task definition to the feature's base implementation file
* Run cformat on modified files
* Change digitizer report usage to Digitizer instead of Pen to avoid
pointer disappearing on Windows.
* Update tmk_core/protocol/vusb/vusb.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Run cformat from docker image
* Remove send_digitizer from host_driver_t and instead rely on the
declaration being the interface to the implementation in each
HW-specific usb implementation.
* Fix build : send_digitizer shouldn't be static in vusb and add
weak-linkage implementation for tests without usb implementation
* Change digitizer user interface to match pointing device's
* Update documentation with new API
Co-authored-by: a-chol <nothing@none.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
|
|
* disambiguate Bootmagic rules in keymaps
The files edited by this commit were added at a point in time where `BOOTMAGIC_ENABLE = yes` enabled full Bootmagic.
This commit edits the files to specify that full Bootmagic is intended.
* remove BOOTMAGIC_ENABLE=full setting
* unify commented BOOTMAGIC_ENABLE rules in keyboards
Explicitly sets `BOOTMAGIC_ENABLE = no` in keyboards where the rule was commented out.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;#[ \t]*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-zA-Z]\+\).*;\1 = no # Virtual DIP switch configuration;g' {} +
```
* remove commented Bootmagic rules from keymap/user level
Command:
```
find keyboards/ layouts/ users/ -type f -name 'rules.mk' -exec sed -i -e '/#.*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*/d' {} +
```
* update keyboard BOOTMAGIC_ENABLE rule formatting
Sets the formatting of BOOTMAGIC_ENABLE rules to `BOOTMAGIC_ENABLE = [value]`, without the inline comments (which will be replaced later).
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
```
* update keyboards' BOOTMAGIC_ENABLE settings
Updates keyboard `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = \)full;\1lite;g' '{}' +
```
* update keymap/user BOOTMAGIC_ENABLE settings
Updates keymap/user `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
```
* remove and replace inline comments in keyboards and keymap/user files
Removes and replaces the inline comments, which have been updated to read `Enable Bootmagic Lite`.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = lite\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = yes\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = no\);\1 # Enable Bootmagic Lite;g' '{}' +
```
* rename improperly named makefiles
Some files intended to be used as makefiles had improper names causing them to not be used as intended when building.
This commit corrects the filenames of the affected files.
* update renamed file with new rule formatting
* update QMK's template files
Updates QMK's `rules.mk` templates to use the new inline comment.
* update QMK Docs
- remove documentation of full Bootmagic
- update links to Bootmagic Lite doc
- add doc for Magic Keycodes
* rules.mk patch for coarse/ixora and coarse/vinta
|
|
|
|
|
|
|
|
* Set bootloader to stm32-dfu for STM32F303
* Set bootloader to stm32-dfu for STM32F0x2
* Set bootloader to stm32-dfu for STM32F4x1
* Set bootloader to stm32duino for sowbug
* Delete redundant bootloader_defs headers
* Add some missing MCU name comments
* Move APM32 dfu-suffix overrides underneath bootloader
* Remove redundant STM32_BOOTLOADER_ADDRESS defines/rules
|
|
* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
|
|
Recent changes to QMK Configurator's API have made it so an info.json file is required for QMK Configurator to know how to render the keyboard in question.
This PR adds info.json files for keyboards that did not have them, with a few exceptions for boards whose layouts I was unable to determine.
* add info.json file for 2key2crawl
* add info.json file for 40percentclub/4x4
* add info.json file for 40percentclub/5x5
* add info.json file for 4pplet/aekiso60/rev_a
* add info.json file for 4pplet/steezy60/rev_a
* add info.json file for 6ball
* add info.json file for 7c8/framework
* add info.json file for aeboards/constellation
* add info.json file for alpine65
* add info.json file for aplyard/aplx6
* add info.json file for arch_36
* add info.json file for arisu
* add info.json file for box75
* add info.json file for butterstick
* add info.json file for four_banger
* add info.json file for geekboards/tester
* add info.json file for handwired/2x5keypad
* add info.json file for handwired/412_64
* add info.json file for handwired/42
* add info.json file for handwired/aplx2
* add info.json file for handwired/brain
* add info.json file for handwired/cans12er
* add info.json file for handwired/ck4x4
* add info.json file for handwired/d48
* add info.json file for handwired/dactyl_manuform/dmote/62key
* add info.json file for handwired/daishi
* add info.json file for handwired/hexon38
* add info.json file for handwired/jot50
* add info.json file for handwired/jotanck
* add info.json file for handwired/jotpad16
* add info.json file for handwired/k8split
* add info.json file for handwired/myskeeb
* add info.json file for handwired/nicekey
* add info.json file for handwired/onekey
* add info.json file for handwired/postageboard
* add info.json file for handwired/riblee_f401
* add info.json file for handwired/riblee_f411
* add info.json file for handwired/rs60
* add info.json file for handwired/splittest
* add info.json file for handwired/trackpoint
* add info.json file for handwired/traveller
* add info.json file for hhkb_lite_2
* add info.json file for honeycomb
* add info.json file for ivy/rev1
* add info.json file for keebio/viterbi
* add info.json file for laptreus
* add info.json file for latin47ble
* add info.json file for latin64ble
* add info.json file for launchpad/rev1
* add info.json file for lets_split_eh/eh
* add info.json file for mechmini/v1
* add info.json file for meira
* add info.json file for meishi
* add info.json file for merge/iso_macro
* add info.json file for mschwingen/modelm
* add info.json file for pabile/p20
* add info.json files for pimentoso/paddino02
rev1, rev2/left, and rev2/right
* add info.json file for rgbkb/pan
* add info.json files for runner3680
3x6, 3x7, 3x8, 4x6, 4x7, 4x8, 5x6, 5x7, and 5x8
* add info.json file for sck/gtm
* add info.json file for splitish
* add info.json file for standaside
* add info.json file for ungodly/launch_pad
* add info.json file for xelus/trinityxttkl
* Revert "add info.json file for rgbkb/pan"
This reverts commit 280b89bc6157023a621a9864f5d74d59d62bb511.
* correct maintainer for ivy/rev1
|
|
|
|
|
|
* Allow forcing re-migration.
* ChibiOS conf upgrade for acheron/arctic
acheron/arctic - 2aedbe9103fff6c37e596c33c9ed337957647368
* ChibiOS conf upgrade for acheron/austin
acheron/austin - c2f4e3b7fc9f1c3d64f47d139bc58367afeca1b7
* ChibiOS conf upgrade for acheron/keebspcb
acheron/keebspcb - 1ba976e409732bfa5c0487dd33e20bec06852ce4
* ChibiOS conf upgrade for acheron/lasgweloth
acheron/lasgweloth - 01a2e70d0d86de0ff05d0b898a6e3b4428ee1581
* ChibiOS conf upgrade for aeboards/ext65/rev2
aeboards/ext65/rev2 - 3c9a45cafb4ed6d9672aaff4548b105193633a87
* ChibiOS conf upgrade for ai03/vega
ai03/vega - 1bd0dfccb99baa69bacd2d55f2bfa72019b8bf80
* ChibiOS conf upgrade for akegata_denki/device_one
akegata_denki/device_one - a013823188660f5fca37c5763f160f8646aed7a7
* ChibiOS conf upgrade for at_at/660m
at_at/660m - 9999583e8bec2772046132a22818482d24e18c84
* ChibiOS conf upgrade for box75
box75 - 1126206109a942237eea96f3a9608e3c9ed55f8e
* ChibiOS conf upgrade for bt66tech/bt66tech60
bt66tech/bt66tech60 - b69120638a8b2c86c008fd0592be918383d8a454
* ChibiOS conf upgrade for cannonkeys/an_c
cannonkeys/an_c - c755f6caaccbe2b30d95661a3d441b836534c29f
* ChibiOS conf upgrade for cannonkeys/atlas
cannonkeys/atlas - 1a18c55492a834b82715516ea4cd4d3d94508743
* ChibiOS conf upgrade for cannonkeys/chimera65
cannonkeys/chimera65 - 6bf226ef353da9106c381a8ac95a9b90529327e5
* ChibiOS conf upgrade for cannonkeys/db60
cannonkeys/db60 - 07e3246f8e3adc5b6918809e6a5aa1ad064b9a09
* ChibiOS conf upgrade for cannonkeys/devastatingtkl
cannonkeys/devastatingtkl - 907d258e29eb7e35b1f868c1ea6148bfd1e3a3f2
* ChibiOS conf upgrade for cannonkeys/instant60
cannonkeys/instant60 - ac876ff6746b08839a3936dd4126b52683b763f4
* ChibiOS conf upgrade for cannonkeys/instant65
cannonkeys/instant65 - 3b8c89ec5fecbdb35cccb00c45e64a798528dbda
* ChibiOS conf upgrade for cannonkeys/iron165
cannonkeys/iron165 - 0814ec4067d9857b0134e38384f272cf7172fb03
* ChibiOS conf upgrade for cannonkeys/obliterated75
cannonkeys/obliterated75 - 0f376e5d9a232c62e9c60f8fdc81d12732352ddc
* ChibiOS conf upgrade for cannonkeys/onyx
cannonkeys/onyx - d35134ebe09046b91ab176035d3742d80b23ed8e
* ChibiOS conf upgrade for cannonkeys/ortho48
cannonkeys/ortho48 - 828dbfbb013ff4fefe75044b3c9fd31fec5e95a1
* ChibiOS conf upgrade for cannonkeys/ortho60
cannonkeys/ortho60 - 2aca4dd4234e0dac828f5fa15ae5b3bc3c0605dc
* ChibiOS conf upgrade for cannonkeys/ortho75
cannonkeys/ortho75 - 4af8aaaded0ff53e9c01473f5968cc169f268647
* ChibiOS conf upgrade for cannonkeys/practice60
cannonkeys/practice60 - e01df551d9483eeb3f825fcc453317fe65f674b5
* ChibiOS conf upgrade for cannonkeys/practice65
cannonkeys/practice65 - 156163789d4c96cdd4787895788c1d02a2367f5c
* ChibiOS conf upgrade for cannonkeys/rekt1800
cannonkeys/rekt1800 - 15882afb6373dea3e5f7ed13c19744ee2463f3bf
* ChibiOS conf upgrade for cannonkeys/sagittarius
cannonkeys/sagittarius - f49fee611ffcc02cb3dc7f249fc8c83f136907b9
* ChibiOS conf upgrade for cannonkeys/satisfaction75
cannonkeys/satisfaction75 - 2c9fbbea3a38820774f6ff436ef51017b545475a
* ChibiOS conf upgrade for cannonkeys/savage65
cannonkeys/savage65 - ddd764be363c46f3e9b1a16151bd02d8f66b2dd4
* ChibiOS conf upgrade for cannonkeys/tmov2
cannonkeys/tmov2 - 7af36cd2a42015838b77697624e90008ffa72778
* ChibiOS conf upgrade for cannonkeys/tsukuyomi
cannonkeys/tsukuyomi - a120bea5dacb2cd6f143458cece46d2860ea196d
* ChibiOS conf upgrade for cheshire/curiosity
cheshire/curiosity - 93d8fe3b7a8e028d4b015941ee71b50afe86bc8a
* ChibiOS conf upgrade for coarse/cordillera
coarse/cordillera - 7d986d3f534786f302cbf74a5e6b7e51ffe60093
* ChibiOS conf upgrade for converter/siemens_tastatur
converter/siemens_tastatur - 3f79f1467bbc56f284aceafd76ab5c6a1cbb68f4
* ChibiOS conf upgrade for cutie_club/borsdorf
cutie_club/borsdorf - f8c6015b7aacfd5edef4f22f719eea30660005e7
* ChibiOS conf upgrade for dekunukem/duckypad
dekunukem/duckypad - d9c162d0867d3925cca2e653a3a3870eac2d23d2
* ChibiOS conf upgrade for ebastler/isometria_75/rev1
ebastler/isometria_75/rev1 - 2ecdd00b8c6cc794a7014747185b88374d5766c0
* ChibiOS conf upgrade for ergodox_infinity
ergodox_infinity - 76736c701db22e890764481c25bd38badf32a1cf
* ChibiOS conf upgrade for ergodox_stm32
ergodox_stm32 - a7bdb0b7822617ca0f9d316a082874ac0fef5964
* ChibiOS conf upgrade for function96
function96 - 1b9e394a86dab24b85d160afe9281b5e7652afe2
* ChibiOS conf upgrade for geekboards/macropad_v2
geekboards/macropad_v2 - de261e46a42cc7b7ff793e26200669f94b1dbb18
* ChibiOS conf upgrade for generic_panda/panda65_01
generic_panda/panda65_01 - 592d2443033875e0309506aa8cb5212389054458
* ChibiOS conf upgrade for handwired/ck4x4
handwired/ck4x4 - 9d7d4af7f2d787afd638e976334cd37c490040d7
* ChibiOS conf upgrade for handwired/onekey/blackpill_f401
handwired/onekey/blackpill_f401 - c9257a30203b3a0e5aa18b35e07281fcd043ab5d
* ChibiOS conf upgrade for handwired/onekey/blackpill_f411
handwired/onekey/blackpill_f411 - dfccc2c6b245cfb561faba60c9f3fc7af8c3db30
* ChibiOS conf upgrade for handwired/onekey/bluepill
handwired/onekey/bluepill - 393f4b94e9a0fbc9cd00de1acde346ad72250b4a
* ChibiOS conf upgrade for handwired/onekey/stm32f0_disco
handwired/onekey/stm32f0_disco - d827881f9bed09fd41c7c4e9d066e96b6643a099
* ChibiOS conf upgrade for handwired/onekey/teensy_32
handwired/onekey/teensy_32 - dd90f6c823da80ba43afa41249a2bdbbab98b04c
* ChibiOS conf upgrade for handwired/onekey/teensy_lc
handwired/onekey/teensy_lc - 34596f2eeb62403cce532d20cf893ebd77fe2d05
* ChibiOS conf upgrade for handwired/pill60/blackpill_f401
handwired/pill60/blackpill_f401 - 20bbccb5058085076357f4fa956eede2c0af86e8
* ChibiOS conf upgrade for handwired/pill60/blackpill_f411
handwired/pill60/blackpill_f411 - e03a4c3ec3b9ba65b8067126a039a8eb2cd10e51
* ChibiOS conf upgrade for handwired/pill60/bluepill
handwired/pill60/bluepill - 2fb721fb4376cde2067eed1c0c8acbf3bf5851c3
* ChibiOS conf upgrade for handwired/riblee_f401
handwired/riblee_f401 - 2823cd98d64c91b146dae343a32176d51772952b
* ChibiOS conf upgrade for handwired/riblee_f411
handwired/riblee_f411 - 5cf7589c9a11c4ed14e7d28676ac836fbb07d013
* ChibiOS conf upgrade for handwired/sono1
handwired/sono1 - d972acee03efb4917fc42f7d72c0a416b67ebd4a
* ChibiOS conf upgrade for handwired/t111
handwired/t111 - f947c1d59025fe04e7d7b999d80e20277be4366c
* ChibiOS conf upgrade for handwired/twadlee/tp69
handwired/twadlee/tp69 - 48ab62464ba1f2651f4468cbec7c6058e3b8c158
* ChibiOS conf upgrade for handwired/z150
handwired/z150 - 35e85696845e965d7f2dcdb372ed20c17d42c2bb
* ChibiOS conf upgrade for hub20
hub20 - f094036a182169b5a73f89f09f2ccaa3e5fc9e7e
* ChibiOS conf upgrade for iron180
iron180 - 5efb6f21c848b3c964795d9debddceac7628933d
* ChibiOS conf upgrade for jm60
jm60 - dbbdbe8b27b3c1d0a25981b2f75728d163d5d299
* ChibiOS conf upgrade for keebio/bdn9/rev2
keebio/bdn9/rev2 - 0031632523dddfc8f7b3a02cf9c5990ebbb3856d
* ChibiOS conf upgrade for keebio/choconum
keebio/choconum - 4484ef6936a497610ca5ae4d378bc07b2bc1b1c7
* ChibiOS conf upgrade for matrix/m20add
matrix/m20add - 6068aeff5b14c26de8838180f4397800abe9f1aa
* ChibiOS conf upgrade for matrix/noah
matrix/noah - fcde175fb1d3f5bf0716ac5a880c2cc9ab4bbf7f
* ChibiOS conf upgrade for misterknife/knife66
misterknife/knife66 - e7f3ceffb94fb8e680da2af27fa7cb1a0a52b699
* ChibiOS conf upgrade for misterknife/knife66_iso
misterknife/knife66_iso - ee027db939c098f908f70f02ffa9cc3952139f70
* ChibiOS conf upgrade for nebula12
nebula12 - 2f3a25b6675dcd0fabe75e7bb63038d3cac19610
* ChibiOS conf upgrade for nemui
nemui - 4030faa372512f766fd747876cb28176302453f9
* ChibiOS conf upgrade for nibiria/stream15
nibiria/stream15 - fd7b09affa208403099ef9bff1b756fac0d4f918
* ChibiOS conf upgrade for nightingale_studios/hailey
nightingale_studios/hailey - 496a44b2f789cc59a6110c7c1c41d57e59c722be
* ChibiOS conf upgrade for planck/rev6
planck/rev6 - 6fb8f0bc21b4ab774ce3d339fdf6f25d96059f10
* ChibiOS conf upgrade for primekb/meridian
primekb/meridian - 8021ed99e8bdf92faab806780186cc924dd59e50
* ChibiOS conf upgrade for projectkb/alice
projectkb/alice - ad7678d475a14c54f28b62d1c1b15f5b4c4448bc
* ChibiOS conf upgrade for projectkb/signature87
projectkb/signature87 - de61338b0a5c477f39c000df8117dd3017c2643d
* ChibiOS conf upgrade for ramonimbao/squishy65
ramonimbao/squishy65 - 2ea1a8b18c39d0e193bbbf5836191874d3aafc53
* ChibiOS conf upgrade for ramonimbao/wete
ramonimbao/wete - a80b3b309f06566adcdf20234d81c1d5aa599b00
* ChibiOS conf upgrade for rart/rartlice
rart/rartlice - c8c80c302428d62bb8b08e3185509a233a94f5f0
* ChibiOS conf upgrade for retro_75
retro_75 - 7434e266bba43ded8ca1ff75d77faa506473ca91
* ChibiOS conf upgrade for rocketboard_16
rocketboard_16 - 1182a8730a84b58eba5a470286b6db6134d36f54
* ChibiOS conf upgrade for satt/vision
satt/vision - c85a28a8d7e321511a17a7e7084d0a7876d1779a
* ChibiOS conf upgrade for technika
technika - 7c59de348f0ec5f6ac9e260806a87aaf16fbafa2
* ChibiOS conf upgrade for tkc/godspeed75
tkc/godspeed75 - e447b39dca393736fbf289049699d5b4748bb8c6
* ChibiOS conf upgrade for tkw/stoutgat/v2/f411
tkw/stoutgat/v2/f411 - 58e9b909379ad107affbff0508e3923264b75426
* ChibiOS conf upgrade for viktus/styrka
viktus/styrka - 36bf0921be79a8b037fdc25343584574a312be60
* ChibiOS conf upgrade for westfoxtrot/prophet
westfoxtrot/prophet - 80036c8f986c8d3261d6b0748d2057eccab6430b
* ChibiOS conf upgrade for whitefox
whitefox - c9eccac0196c3e2e2ea6c90d3036283a3eabff2c
* ChibiOS conf upgrade for wolfmarkclub/wm1
wolfmarkclub/wm1 - 0d22a426255b829a7805bd6a3ff927198b1e31b4
* ChibiOS conf upgrade for xelus/kangaroo
xelus/kangaroo - fdb1ffb66f4841f662e968929f058d4fd403c97e
* ChibiOS conf upgrade for xelus/trinityxttkl
xelus/trinityxttkl - a9641e5b39b7bb38351b9109f0f381837b2e8e79
* ChibiOS conf upgrade for xelus/valor_frl_tkl
xelus/valor_frl_tkl - 6c3b577852736a68727ec319c30712b3088e65cd
* ChibiOS conf upgrade for xiaomi/mk02
xiaomi/mk02 - 4c1406ebfee73551a844ef7ab29fc5788d7e875c
* ChibiOS conf upgrade for zoo/wampus
zoo/wampus - 930c903e85478e220a235f45593c03512c66bc2a
* ChibiOS conf upgrade for zvecr/split_blackpill
zvecr/split_blackpill - c0e3e1583262e4cb0ebfe2efa6356ed6c5c957ca
|
|
|
|
|
|
|
|
|
|
|
|
* exclude all of handwired
* exclude more keyboards from CI
|
|
|