summaryrefslogtreecommitdiff
path: root/platforms/chibios/drivers/vendor
diff options
context:
space:
mode:
Diffstat (limited to 'platforms/chibios/drivers/vendor')
-rw-r--r--platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c20
1 files changed, 17 insertions, 3 deletions
diff --git a/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c b/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c
index 949fc6dd93..d933dc1f5d 100644
--- a/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c
+++ b/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c
@@ -142,6 +142,7 @@ void pio_serve_interrupt(void) {
// the generated low level with 360mV will generate a logical zero.
static inline void enter_rx_state(void) {
osalSysLock();
+ nvicEnableVector(RP_USBCTRL_IRQ_NUMBER, RP_IRQ_USB0_PRIORITY);
// Wait for the transmitting state machines FIFO to run empty. At this point
// the last byte has been pulled from the transmitting state machines FIFO
// into the output shift register. We have to wait a tiny bit more until
@@ -163,6 +164,9 @@ static inline void enter_rx_state(void) {
static inline void leave_rx_state(void) {
osalSysLock();
+ // We don't want to be interrupted by frequent (1KHz) USB interrupts while
+ // doing our timing critical sending operation.
+ nvicDisableVector(RP_USBCTRL_IRQ_NUMBER);
// In Half-duplex operation the tx pin dual-functions as sender and
// receiver. To not receive the data we will send, we disable the receiving
// state machine.
@@ -194,12 +198,21 @@ static inline msg_t sync_tx(sysinterval_t timeout) {
msg_t msg = MSG_OK;
osalSysLock();
while (pio_sm_is_tx_fifo_full(pio, tx_state_machine)) {
+#if !defined(SERIAL_USART_FULL_DUPLEX)
+ // Enable USB interrupts again, because we might sleep for a long time
+ // here and don't want to be disconnected from the host.
+ nvicEnableVector(RP_USBCTRL_IRQ_NUMBER, RP_IRQ_USB0_PRIORITY);
+#endif
pio_set_irq0_source_enabled(pio, pis_sm0_tx_fifo_not_full + tx_state_machine, true);
msg = osalThreadSuspendTimeoutS(&tx_thread, timeout);
if (msg < MSG_OK) {
break;
}
}
+#if !defined(SERIAL_USART_FULL_DUPLEX)
+ // Entering timing critical territory again.
+ nvicDisableVector(RP_USBCTRL_IRQ_NUMBER);
+#endif
osalSysUnlock();
return msg;
}
@@ -412,11 +425,12 @@ static inline void pio_init(pin_t tx_pin, pin_t rx_pin) {
pio_set_irq0_source_enabled(pio, pis_sm0_tx_fifo_not_full + tx_state_machine, true);
pio_set_irq0_source_enabled(pio, pis_interrupt0, true);
- // Enable PIO specific interrupt vector
+ // Enable PIO specific interrupt vector, as the pio implementation is timing
+ // critical we use the highest possible priority.
#if defined(SERIAL_PIO_USE_PIO1)
- nvicEnableVector(RP_PIO1_IRQ_0_NUMBER, RP_IRQ_UART0_PRIORITY);
+ nvicEnableVector(RP_PIO1_IRQ_0_NUMBER, CORTEX_MAX_KERNEL_PRIORITY);
#else
- nvicEnableVector(RP_PIO0_IRQ_0_NUMBER, RP_IRQ_UART0_PRIORITY);
+ nvicEnableVector(RP_PIO0_IRQ_0_NUMBER, CORTEX_MAX_KERNEL_PRIORITY);
#endif
enter_rx_state();