diff options
Diffstat (limited to 'keyboards/s60-x/rgb')
| -rw-r--r-- | keyboards/s60-x/rgb/config.h | 7 | ||||
| -rw-r--r-- | keyboards/s60-x/rgb/rules.mk | 65 |
2 files changed, 16 insertions, 56 deletions
diff --git a/keyboards/s60-x/rgb/config.h b/keyboards/s60-x/rgb/config.h index 26b246e573..fbc143487e 100644 --- a/keyboards/s60-x/rgb/config.h +++ b/keyboards/s60-x/rgb/config.h @@ -9,6 +9,7 @@ /* key matrix pins */ #define MATRIX_ROW_PINS { B5, B4, D7, D6, D4 } #define MATRIX_COL_PINS { D0, D1, D2, D3, D5, B6, C6, C7, F1, F0, E6, B3, B2, B1, B0 } +#define UNUSED_PINS /* number of backlight levels */ #define BACKLIGHT_PIN B7 @@ -16,6 +17,12 @@ #define BACKLIGHT_LEVELS 3 #endif +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE + +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + /* prevent stuck modifiers */ #define PREVENT_STUCK_MODIFIERS diff --git a/keyboards/s60-x/rgb/rules.mk b/keyboards/s60-x/rgb/rules.mk index c303af4bcc..6953cc6d6d 100644 --- a/keyboards/s60-x/rgb/rules.mk +++ b/keyboards/s60-x/rgb/rules.mk @@ -1,56 +1,9 @@ -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= no # Commands for debug and configuration -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -AUDIO_ENABLE ?= no -RGBLIGHT_ENABLE ?= yes
\ No newline at end of file +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +RGBLIGHT_ENABLE ?= yes # Enable RGB light + +ifndef QUANTUM_DIR + include ../../../Makefile +endif
\ No newline at end of file |