summaryrefslogtreecommitdiff
path: root/keyboards/s60-x/rgb
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/s60-x/rgb')
-rw-r--r--keyboards/s60-x/rgb/config.h7
-rw-r--r--keyboards/s60-x/rgb/rules.mk65
2 files changed, 16 insertions, 56 deletions
diff --git a/keyboards/s60-x/rgb/config.h b/keyboards/s60-x/rgb/config.h
index 26b246e573..fbc143487e 100644
--- a/keyboards/s60-x/rgb/config.h
+++ b/keyboards/s60-x/rgb/config.h
@@ -9,6 +9,7 @@
/* key matrix pins */
#define MATRIX_ROW_PINS { B5, B4, D7, D6, D4 }
#define MATRIX_COL_PINS { D0, D1, D2, D3, D5, B6, C6, C7, F1, F0, E6, B3, B2, B1, B0 }
+#define UNUSED_PINS
/* number of backlight levels */
#define BACKLIGHT_PIN B7
@@ -16,6 +17,12 @@
#define BACKLIGHT_LEVELS 3
#endif
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
/* prevent stuck modifiers */
#define PREVENT_STUCK_MODIFIERS
diff --git a/keyboards/s60-x/rgb/rules.mk b/keyboards/s60-x/rgb/rules.mk
index c303af4bcc..6953cc6d6d 100644
--- a/keyboards/s60-x/rgb/rules.mk
+++ b/keyboards/s60-x/rgb/rules.mk
@@ -1,56 +1,9 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no # Console for debug(+400)
-COMMAND_ENABLE ?= no # Commands for debug and configuration
-SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= yes \ No newline at end of file
+CONSOLE_ENABLE ?= no # Console for debug(+400)
+COMMAND_ENABLE ?= no # Commands for debug and configuration
+NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE ?= yes # Enable RGB light
+
+ifndef QUANTUM_DIR
+ include ../../../Makefile
+endif \ No newline at end of file