diff options
Diffstat (limited to 'keyboards/kinesis/stapelberg')
| -rw-r--r-- | keyboards/kinesis/stapelberg/Makefile | 3 | ||||
| -rw-r--r-- | keyboards/kinesis/stapelberg/config.h | 50 | ||||
| -rw-r--r-- | keyboards/kinesis/stapelberg/readme.md | 58 | ||||
| -rw-r--r-- | keyboards/kinesis/stapelberg/rules.mk | 10 | ||||
| -rw-r--r-- | keyboards/kinesis/stapelberg/stapelberg.c | 28 | ||||
| -rw-r--r-- | keyboards/kinesis/stapelberg/stapelberg.h | 72 |
6 files changed, 221 insertions, 0 deletions
diff --git a/keyboards/kinesis/stapelberg/Makefile b/keyboards/kinesis/stapelberg/Makefile new file mode 100644 index 0000000000..bd09e5885d --- /dev/null +++ b/keyboards/kinesis/stapelberg/Makefile @@ -0,0 +1,3 @@ +ifndef MAKEFILE_INCLUDED + include ../../../Makefile +endif diff --git a/keyboards/kinesis/stapelberg/config.h b/keyboards/kinesis/stapelberg/config.h new file mode 100644 index 0000000000..0677e0adeb --- /dev/null +++ b/keyboards/kinesis/stapelberg/config.h @@ -0,0 +1,50 @@ +#ifndef STAPELBERG_CONFIG_H +#define STAPELBERG_CONFIG_H + +#include "../config.h" + +/* USB Device descriptor parameter */ +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0002 + +/* key matrix size */ +#define MATRIX_ROWS 15 +#define MATRIX_COLS 7 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D4, D5, D6, D7, C0, C1, C2, C3, C4, C5, C6 } +#define MATRIX_COL_PINS { B0, B1, B2, B3, B4, B5, B6 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* don't know if this should be defined at the board or top level. Assuming board +#define MOUSEKEY_DELAY 100 +#define MOUSEKEY_INTERVAL 20 +#define MOUSEKEY_MAX_SPEED 3 +#define MOUSEKEY_TIME_TO_MAX 10 +*/ + +#define IGNORE_MOD_TAP_INTERRUPT + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + + +#endif diff --git a/keyboards/kinesis/stapelberg/readme.md b/keyboards/kinesis/stapelberg/readme.md new file mode 100644 index 0000000000..1a408a15f8 --- /dev/null +++ b/keyboards/kinesis/stapelberg/readme.md @@ -0,0 +1,58 @@ +# kinesis_stapelberg keyboard firmware + +This folder contains the firmware customization required to run QMK on the custom controller for the Kinesis Advantage created by Michael Stapelberg. +It differs from the `alvicstep keyboard in that the existing QMK Kinesis Advantage project uses the existing controller board provided by Kinesis. + +The controller board hardware is described +[here](http://michael.stapelberg.de/Artikel/kinesis_custom_controller) + +Mapping the pin assignments was done using the corresponding matrix description provided at this +[link](https://github.com/stapelberg/kinesis-firmware/blob/master/kb_kinesis/config.kspec) + +This code makes no attempt to drive the four LEDs provided on the controller board. + + +## Building the Hardware + +If you want to perform this customization, these parts may be helpful. + +| Function | Quantity | Vendor | Part Number | +| ------------------------------------------------------ | -------- | ------- | ------------ | +| 13 pin connector for function keys and finger keywells | 4 | Digi-Key | WM14526-ND | +| 10 pin headers for thumb clusters | 4 | Digi-Key | 609-3250-ND | +| 8 pin cable for thumb clusters | 2 | Digi-Key | SAM8928-ND | +| Teensy++ 2.0 | 1 | Digi-Key | 1528-1056-ND | +| 2 pin right angle header for reset | 1 | Digi-Key | 3M9467-ND | +| Reset cables | 2 | Sparkfun | PRT-09140 | + +The board and connections are shown here + + +The Teensy mounting detail can be seen here. +I used a socket for prototyping. + + + +Since the proper mounting of the Teensy board places the reset button in a tight space, I added a 2-pin header to the reset and ground pins on the edge of the board. +Shorting these two pins together will reset the board. +I also put female to male header jumper cables on these so they could be accessed outside the enclosure. +The exterior cables can be seen here. + + + +## Keymaps + +### Default + +To build with the default keymap, run `make default` while in the +`kinesis_stapelberg` working directory. + +### Dvorak + +This keymap contains a dvorak implementation as well as media and symbol layers. + +Run `make dvorak` while in the `kinesis_stapelberg` working directory. + + + +
\ No newline at end of file diff --git a/keyboards/kinesis/stapelberg/rules.mk b/keyboards/kinesis/stapelberg/rules.mk new file mode 100644 index 0000000000..fb421a34fc --- /dev/null +++ b/keyboards/kinesis/stapelberg/rules.mk @@ -0,0 +1,10 @@ +ifndef QUANTUM_DIR + include ../../../Makefile +endif + +# just silently stop, since we need to upload with teensy uploader +upload: build + + + + diff --git a/keyboards/kinesis/stapelberg/stapelberg.c b/keyboards/kinesis/stapelberg/stapelberg.c new file mode 100644 index 0000000000..111db81feb --- /dev/null +++ b/keyboards/kinesis/stapelberg/stapelberg.c @@ -0,0 +1,28 @@ +#include "stapelberg.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} diff --git a/keyboards/kinesis/stapelberg/stapelberg.h b/keyboards/kinesis/stapelberg/stapelberg.h new file mode 100644 index 0000000000..c90fc3d52d --- /dev/null +++ b/keyboards/kinesis/stapelberg/stapelberg.h @@ -0,0 +1,72 @@ +#ifndef KINESIS_STAPELBERG_H +#define KINESIS_STAPELBERG_H + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The first section contains all of the arguments as on the physical keyboard +// The second converts the arguments into the 2-D scanned array + +#define KEYMAP( \ + kC0,kD0,kE0,kC1,kD1,kE1,kC2,kD2,kE2, \ + k00,k10,k20,k30,k40,k50, \ + k01,k11,k21,k31,k41,k51, \ + k02,k12,k22,k32,k42,k52, \ + k03,k13,k23,k33,k43,k53, \ + k14,k24,k34,k54, \ + k56,k55, \ + k35, \ + k36,k46,k25, \ + kC3,kD3,kE3,kC4,kD4,kE4,kC5,kE5,kD5, \ + k60,k70,k80,k90,kA0,kB0, \ + k61,k71,k81,k91,kA1,kB1, \ + k62,k72,k82,k92,kA2,kB2, \ + k63,k73,k83,k93,kA3,kB3, \ + k64,k84,k94,kA4, \ + k96,k85, \ + k86, \ + k66,k75,k65 \ +) { \ + { k00, k01, k02, k03, KC_NO, KC_NO, KC_NO }, \ + { k10, k11, k12, k13, k14, KC_NO, KC_NO }, \ + { k20, k21, k22, k23, k24, k25, KC_NO }, \ + { k30, k31, k32, k33, k34, k35, k36 }, \ + { k40, k41, k42, k43, KC_NO, KC_NO, k46 }, \ + { k50, k51, k52, k53, k54, k55, k56 }, \ + { k60, k61, k62, k63, k64, k65, k66 }, \ + { k70, k71, k72, k73, KC_NO, k75, KC_NO }, \ + { k80, k81, k82, k83, k84, k85, k86 }, \ + { k90, k91, k92, k93, k94, KC_NO, k96 }, \ + { kA0, kA1, kA2, kA3, kA4, KC_NO, KC_NO }, \ + { kB0, kB1, kB2, kB3, KC_NO, KC_NO, KC_NO }, \ + { kC0, kC1, kC2, kC3, kC4, kC5, KC_NO }, \ + { kD0, kD1, kD2, kD3, kD4, kD5, KC_NO }, \ + { kE0, kE1, kE2, kE3, kE4, kE5, KC_NO } \ +} + +/* +This is the Stapelberg matrix as published at +https://github.com/stapelberg/kinesis-firmware/blob/master/kb_kinesis/config.kspec +Along with the pins for each row and column + PB0 PB1 PB2 PB3 PB4 PB5 PB6 + kx0 kx1 kx2 kx3 kx4 kx5 kx6 +PD0 k0x Row: EQL TAB CAP LSH X2 -- -- +PD1 k1x Row: 1 Q A Z BQ -- -- +PD2 k2x Row: 2 W S X INS END -- +PD3 k3x Row: 3 E D C LFT HOM BAK +PD4 k4x Row: 4 R F V -- -- DEL +PD5 k5x Row: 5 T G B RT LAL LCT +PD6 k6x Row: 6 Y H N UP SPC PGD +PD7 k7x Row: 7 U J M -- RET -- +PB0 k8x Row: 8 I K COM DWN RCT PGU +PB1 k9x Row: 9 O L PER LBR -- RAL +PB2 kAx Row: 0 P SEM SLA RBR -- -- +PB3 kBx Row: MIN BSL APO RSH X1 -- -- +PB4 kCx Row: ESC F3 F6 F9 F12 PAU -- +PB5 kDx Row: F1 F4 F7 F10 PRT PRG -- +PB6 kEx Row: F2 F5 F8 F11 SLK KEY -- +*/ + + + +#endif |