summaryrefslogtreecommitdiff
path: root/keyboards/kc60
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/kc60')
-rw-r--r--keyboards/kc60/Makefile76
-rw-r--r--keyboards/kc60/config.h2
-rw-r--r--keyboards/kc60/keymaps/dbroqua/keymap.c10
-rw-r--r--keyboards/kc60/keymaps/workman-dead/keymap.c8
-rw-r--r--keyboards/kc60/keymaps/workman-dead/readme.md (renamed from keyboards/kc60/keymaps/workman-dead/README.md)0
-rw-r--r--keyboards/kc60/readme.md12
-rw-r--r--keyboards/kc60/rules.mk71
7 files changed, 89 insertions, 90 deletions
diff --git a/keyboards/kc60/Makefile b/keyboards/kc60/Makefile
index 0d17d32dac..57b2ef62e5 100644
--- a/keyboards/kc60/Makefile
+++ b/keyboards/kc60/Makefile
@@ -1,77 +1,3 @@
-# project specific files
-SRC = led.c
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes # Console for debug(+400)
-COMMAND_ENABLE ?= yes # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no # MIDI controls
-UNICODE_ENABLE ?= no # Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no # Audio output on port C6
-
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
include ../../Makefile
endif
-
diff --git a/keyboards/kc60/config.h b/keyboards/kc60/config.h
index c4a9b9ff82..29695d0b9d 100644
--- a/keyboards/kc60/config.h
+++ b/keyboards/kc60/config.h
@@ -62,7 +62,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
//#define MATRIX_HAS_GHOST
/* number of backlight levels */
-#define BACKLIGHT_LEVELS 3
+#define BACKLIGHT_LEVELS 5
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
#define LOCKING_SUPPORT_ENABLE
diff --git a/keyboards/kc60/keymaps/dbroqua/keymap.c b/keyboards/kc60/keymaps/dbroqua/keymap.c
index e17827fad9..1b645ea938 100644
--- a/keyboards/kc60/keymaps/dbroqua/keymap.c
+++ b/keyboards/kc60/keymaps/dbroqua/keymap.c
@@ -34,9 +34,9 @@ const uint16_t PROGMEM fn_actions[] = {
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
/* Qwerty
* ,-----------------------------------------------------------------------------------------.
- * | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | ` | Bksp|
+ * | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
* |-----------------------------------------------------------------------------------------+
- * | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | \ |
+ * | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Bksp |
* |-----------------------------------------------------------------------------------------+
* | Caps/FN1| A | S | D | F | G | H | J | K | L | ; | ' | Enter |
* |-----------------------------------------------------------------------------------------+
@@ -46,11 +46,11 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
* `-----------------------------------------------------------------------------------------'
*/
[0] = KEYMAP( /* Basic QWERTY */
- KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, \
- KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \
+ KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \
LT(_FNCAPS, KC_CAPS), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \
KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_FNRIGHTSHIFT), KC_UP, \
- KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_BSPC, KC_RALT, KC_LEFT, KC_DOWN, KC_RIGHT \
+ KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_GRV, KC_RALT, KC_LEFT, KC_DOWN, KC_RIGHT \
),
/* Layer 1
diff --git a/keyboards/kc60/keymaps/workman-dead/keymap.c b/keyboards/kc60/keymaps/workman-dead/keymap.c
index 9786e37d8c..9e3b9bb656 100644
--- a/keyboards/kc60/keymaps/workman-dead/keymap.c
+++ b/keyboards/kc60/keymaps/workman-dead/keymap.c
@@ -56,7 +56,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
KC_TABM, KC_Q, KC_D, KC_R, KC_W, KC_B, KC_J, KC_F, KC_U, KC_P, KC_SCLN, KC_LBRC, KC_RBRC, KC_BSLS, \
KC_LCTL, KC_A, KC_S, KC_H, KC_T, KC_G, KC_Y, KC_N, KC_E, KC_O, KC_I, KC_QUOT, _______, KC_ENT, \
KC_LSFT, _______, KC_Z, KC_X, KC_M, KC_C, KC_V, KC_K, KC_L, DK_ACT, KC_DOT, KC_SLSH, _______, KC_RSFT, \
- KC_LCTL, KC_LALT, KC_LGUI, KC_SPFN, KC_NO, KC_RALT, KC_RGUI, KC_RCTL, KC_DFQW),
+ KC_LCTL, KC_LALT, KC_LGUI, KC_SPFN, _______, KC_RALT, KC_RGUI, KC_RCTL, KC_DFQW),
// QWERTY
/*
@@ -77,7 +77,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
KC_TABM, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \
KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, _______, KC_ENT, \
KC_LSFT, _______, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, DK_ACT, KC_DOT, KC_SLSH, _______, KC_RSFT, \
- KC_LCTL, KC_LALT, KC_LGUI, KC_SPFN, KC_NO, KC_RALT, KC_RGUI, KC_RCTL, KC_DOWN),
+ KC_LCTL, KC_LALT, KC_LGUI, KC_SPFN, _______, KC_RALT, KC_RGUI, KC_RCTL, KC_DFWM),
// dead key layer
/*
@@ -98,7 +98,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
XXXXXXX, KC_PERC, KC_AMPR, KC_QUES, KC_PLUS, KC_AT, KC_DLR, KC_UNDS, KC_LBRC, KC_RBRC, KC_EXLM, KC_TILD, KC_CIRC, _______, \
_______, KC_HASH, KC_LPRN, KC_EQL, KC_0, KC_LCBR, KC_RCBR, KC_1, KC_ASTR, KC_RPRN, KC_MINS, KC_GRV, _______, KC_CENT, \
_______, _______, KC_6, KC_7, KC_8, KC_9, KC_PIPE, KC_BSLS, KC_2, DK_REL, KC_4, KC_5, _______, _______, \
- KC_LCTL, KC_LALT, KC_LGUI, KC_COMS, KC_NO, KC_RALT, KC_RGUI, KC_RCTL, _______),
+ KC_LCTL, KC_LALT, KC_LGUI, KC_COMS, _______, KC_RALT, KC_RGUI, KC_RCTL, _______),
// function layer
/*
@@ -119,7 +119,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
KC_ESC, KC_CMDQ, KC_CMDD, KC_CSTB, KC_C_TB, _______, _______, KC_PGDN, KC_UP, KC_PGUP, _______, _______, _______, KC_INS, \
KC_LSFT, KC_CMDA, KC_CMDS, KC_C_LF, KC_C_RT, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, KC_HOME, KC_END, _______, KC_BSPC, \
KC_LSFT, _______, KC_CMDZ, KC_CMDX, _______, KC_CMDC, KC_CMDV, KC_VOLD, KC_VOLU, KC_MUTE, _______, _______, _______, _______, \
- KC_LCTL, KC_LALT, KC_LGUI, KC_TRNS, KC_NO, KC_RALT, KC_RGUI, KC_RCTL, RESET),
+ KC_LCTL, KC_LALT, KC_LGUI, KC_TRNS, _______, KC_RALT, KC_RGUI, KC_RCTL, RESET),
// mouse layer
/*
diff --git a/keyboards/kc60/keymaps/workman-dead/README.md b/keyboards/kc60/keymaps/workman-dead/readme.md
index f1fcdc9606..f1fcdc9606 100644
--- a/keyboards/kc60/keymaps/workman-dead/README.md
+++ b/keyboards/kc60/keymaps/workman-dead/readme.md
diff --git a/keyboards/kc60/readme.md b/keyboards/kc60/readme.md
index b29c6be302..da84f6159a 100644
--- a/keyboards/kc60/readme.md
+++ b/keyboards/kc60/readme.md
@@ -10,25 +10,27 @@ Download or clone the whole firmware and navigate to the keyboards/kc60 folder.
Depending on which keymap you would like to use, you will have to compile slightly differently.
### Default
-To build with the default keymap, simply run `make`.
+To build with the default keymap, simply run `make default`.
### Other Keymaps
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
-To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
+
```
-$ make KEYMAP=[default|jack|<name>]
+$ make [default|jack|<name>]
```
+
Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
## WS2812 Support
![Image of KC60 with RGB Underglow](keymaps/ws2812/ws2812_example.jpg)
-Build with WS2812 Support by running `make KEYMAP=ws2812`.
+Build with WS2812 Support by running `make ws2812`.
## Warning
For those who want to use 2x1U instead of classic backspace you need to use K0D and K49 like this:
* K0D represents the key at the right of =.
* K49 represents the last key of the row (is wired at the right of the space key on the PCB)
-In kc60.h I've put several definitions' examples of possible layouts proposed by online editor (http://123.57.250.164:9128/). \ No newline at end of file
+In kc60.h I've put several definitions' examples of possible layouts proposed by online editor (http://123.57.250.164:9128/).
diff --git a/keyboards/kc60/rules.mk b/keyboards/kc60/rules.mk
new file mode 100644
index 0000000000..a935ed19ee
--- /dev/null
+++ b/keyboards/kc60/rules.mk
@@ -0,0 +1,71 @@
+# project specific files
+SRC = led.c
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no # MIDI controls
+UNICODE_ENABLE ?= no # Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no # Audio output on port C6