diff options
Diffstat (limited to 'keyboards/hotdox/rules.mk')
-rw-r--r-- | keyboards/hotdox/rules.mk | 82 |
1 files changed, 0 insertions, 82 deletions
diff --git a/keyboards/hotdox/rules.mk b/keyboards/hotdox/rules.mk deleted file mode 100644 index f785cdd060..0000000000 --- a/keyboards/hotdox/rules.mk +++ /dev/null @@ -1,82 +0,0 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = matrix.c \ - i2c_master.c \ - left.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section -BOOTLOADER = atmel-dfu - -# Build Options -# comment out to disable the options. -# -CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDone -UNICODE_ENABLE = yes # Unicode -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA -USB_6KRO_ENABLE = no # USB 6key Rollover -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor -SWAP_HANDS_ENABLE = no # Disable Onehand -RGBLIGHT_ENABLE = no -MIDI_ENABLE = no - -LAYOUTS = ergodox |