diff options
Diffstat (limited to 'keyboards/hhkb/rules.mk')
| -rw-r--r-- | keyboards/hhkb/rules.mk | 110 |
1 files changed, 0 insertions, 110 deletions
diff --git a/keyboards/hhkb/rules.mk b/keyboards/hhkb/rules.mk deleted file mode 100644 index 3abd31c33a..0000000000 --- a/keyboards/hhkb/rules.mk +++ /dev/null @@ -1,110 +0,0 @@ - - -# project specific files -SRC = matrix.c - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -#OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# as per original hasu settings -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -CUSTOM_MATRIX = yes # Custom matrix file for the HHKB -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -# NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -# MIDI_ENABLE = yes # MIDI controls -# UNICODE_ENABLE = yes # Unicode -# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -# HHKB_RN42_ENABLE = yes # Enable support for hasu's BT alt controller -- code borrowed from tmk source tree. - -# Either uncomment the HHKB_RN42_ENABLE line above, or run make enabling the -# feature. Be sure to clean any existing build before trying to enable rn42 -# support. For example: -# -# make hhkb-keymap-clean -# make hhkb-keymap-dfu HHKB_RN42_ENABLE=yes - -ifeq ($(strip $(HHKB_RN42_ENABLE)), yes) - -OPT_DEFS += -DHHKB_RN42_ENABLE - -# Support for the RN42 Bluetooth module. This is the BT module in Hasu's BT -# HHKB Alt controller. -RN42_DIR = rn42 - -SRC += serial_uart.c \ - rn42/suart.S \ - rn42/rn42.c \ - rn42/rn42_task.c \ - rn42/battery.c \ - rn42/main.c - -VPATH += $(RN42_DIR) - -endif - - -# debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION -# debug-on: all - -# debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT -# debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS)) -# debug-off: all |