diff options
Diffstat (limited to 'keyboards/gh60')
| -rw-r--r-- | keyboards/gh60/Makefile | 148 | ||||
| -rw-r--r-- | keyboards/gh60/config.h | 322 | ||||
| -rw-r--r-- | keyboards/gh60/gh60.c | 50 | ||||
| -rw-r--r-- | keyboards/gh60/gh60.h | 148 | ||||
| -rw-r--r-- | keyboards/gh60/keymaps/robotmaxtron/Makefile | 224 | ||||
| -rw-r--r-- | keyboards/gh60/keymaps/robotmaxtron/config.h | 380 | ||||
| -rw-r--r-- | keyboards/gh60/pinout.txt | 34 | ||||
| -rw-r--r-- | keyboards/gh60/readme.md | 120 |
8 files changed, 713 insertions, 713 deletions
diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile index 39a9cc0ae1..075b77256f 100644 --- a/keyboards/gh60/Makefile +++ b/keyboards/gh60/Makefile @@ -1,74 +1,74 @@ -
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-# CONSOLE_ENABLE ?= yes # Console for debug(+400)
-# COMMAND_ENABLE ?= yes # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-# MIDI_ENABLE ?= YES # MIDI controls
-# UNICODE_ENABLE ?= YES # Unicode
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-
-ifndef QUANTUM_DIR
- include ../../Makefile
-endif
-
+ + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID + + +ifndef QUANTUM_DIR + include ../../Makefile +endif + diff --git a/keyboards/gh60/config.h b/keyboards/gh60/config.h index 4813c4e786..97753bc069 100644 --- a/keyboards/gh60/config.h +++ b/keyboards/gh60/config.h @@ -1,161 +1,161 @@ -/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID 0xFEED
-#define PRODUCT_ID 0x6060
-#define DEVICE_VER 0x0001
-#define MANUFACTURER geekhack
-#define PRODUCT GH60
-#define DESCRIPTION t.m.k. keyboard firmware for GH60
-
-/* key matrix size */
-#define MATRIX_ROWS 5
-#define MATRIX_COLS 14
-
-/*
- * Keyboard Matrix Assignments
- *
- * Change this to how you wired your keyboard
- * COLS: AVR pins used for columns, left to right
- * ROWS: AVR pins used for rows, top to bottom
- * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
- * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
- *
-*/
- #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
-// Rev A
-// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 }
-// Rev B/C
- #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }
-#define UNUSED_PINS
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCING_DELAY 5
-
-/* define if matrix has ghost (lacks anti-ghosting diodes) */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-#define BACKLIGHT_LEVELS 3
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
-//#define FORCE_NKRO
-
-/*
- * Magic Key Options
- *
- * Magic keys are hotkey commands that allow control over firmware functions of
- * the keyboard. They are best used in combination with the HID Listen program,
- * found here: https://www.pjrc.com/teensy/hid_listen.html
- *
- * The options below allow the magic key functionality to be changed. This is
- * useful if your keyboard/keypad is missing keys and you want magic key support.
- *
- */
-
-/* key combination for magic key command */
-#define IS_COMMAND() ( \
- keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-/* control how magic key switches layers */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
-
-/* override magic key keymap */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
-//#define MAGIC_KEY_HELP1 H
-//#define MAGIC_KEY_HELP2 SLASH
-//#define MAGIC_KEY_DEBUG D
-//#define MAGIC_KEY_DEBUG_MATRIX X
-//#define MAGIC_KEY_DEBUG_KBD K
-//#define MAGIC_KEY_DEBUG_MOUSE M
-//#define MAGIC_KEY_VERSION V
-//#define MAGIC_KEY_STATUS S
-//#define MAGIC_KEY_CONSOLE C
-//#define MAGIC_KEY_LAYER0_ALT1 ESC
-//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
-//#define MAGIC_KEY_LAYER0 0
-//#define MAGIC_KEY_LAYER1 1
-//#define MAGIC_KEY_LAYER2 2
-//#define MAGIC_KEY_LAYER3 3
-//#define MAGIC_KEY_LAYER4 4
-//#define MAGIC_KEY_LAYER5 5
-//#define MAGIC_KEY_LAYER6 6
-//#define MAGIC_KEY_LAYER7 7
-//#define MAGIC_KEY_LAYER8 8
-//#define MAGIC_KEY_LAYER9 9
-//#define MAGIC_KEY_BOOTLOADER PAUSE
-//#define MAGIC_KEY_LOCK CAPS
-//#define MAGIC_KEY_EEPROM E
-//#define MAGIC_KEY_NKRO N
-//#define MAGIC_KEY_SLEEP_LED Z
-
-/*
- * Feature disable options
- * These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-//#define NO_DEBUG
-
-/* disable print */
-//#define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-
-#endif
+/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT GH60 +#define DESCRIPTION t.m.k. keyboard firmware for GH60 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ + #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +// Rev A +// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 } +// Rev B/C + #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/gh60/gh60.c b/keyboards/gh60/gh60.c index 255d87de99..f5a158e12f 100644 --- a/keyboards/gh60/gh60.c +++ b/keyboards/gh60/gh60.c @@ -1,25 +1,25 @@ -#include "gh60.h"
-
-void led_set_kb(uint8_t usb_led) {
- // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
-
- if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
- gh60_caps_led_on();
- } else {
- gh60_caps_led_off();
- }
-
- // if (usb_led & (1<<USB_LED_NUM_LOCK)) {
- // gh60_esc_led_on();
- // } else {
- // gh60_esc_led_off();
- // }
-
- // if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
- // gh60_fn_led_on();
- // } else {
- // gh60_fn_led_off();
- // }
-
- led_set_user(usb_led);
-}
+#include "gh60.h" + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + gh60_caps_led_on(); + } else { + gh60_caps_led_off(); + } + + // if (usb_led & (1<<USB_LED_NUM_LOCK)) { + // gh60_esc_led_on(); + // } else { + // gh60_esc_led_off(); + // } + + // if (usb_led & (1<<USB_LED_SCROLL_LOCK)) { + // gh60_fn_led_on(); + // } else { + // gh60_fn_led_off(); + // } + + led_set_user(usb_led); +} diff --git a/keyboards/gh60/gh60.h b/keyboards/gh60/gh60.h index ca30562a44..82624b6148 100644 --- a/keyboards/gh60/gh60.h +++ b/keyboards/gh60/gh60.h @@ -1,74 +1,74 @@ -#ifndef GH60_H
-#define GH60_H
-
-#include "quantum.h"
-#include "led.h"
-
-/* GH60 LEDs
- * GPIO pads
- * 0 F7 WASD LEDs
- * 1 F6 ESC LED
- * 2 F5 FN LED
- * 3 F4 POKER Arrow LEDs
- * B2 Capslock LED
- * B0 not connected
- */
-inline void gh60_caps_led_on(void) { DDRB |= (1<<2); PORTB &= ~(1<<2); }
-inline void gh60_poker_leds_on(void) { DDRF |= (1<<4); PORTF &= ~(1<<4); }
-inline void gh60_fn_led_on(void) { DDRF |= (1<<5); PORTF &= ~(1<<5); }
-inline void gh60_esc_led_on(void) { DDRF |= (1<<6); PORTF &= ~(1<<6); }
-inline void gh60_wasd_leds_on(void) { DDRF |= (1<<7); PORTF &= ~(1<<7); }
-
-inline void gh60_caps_led_off(void) { DDRB &= ~(1<<2); PORTB &= ~(1<<2); }
-inline void gh60_poker_leds_off(void) { DDRF &= ~(1<<4); PORTF &= ~(1<<4); }
-inline void gh60_fn_led_off(void) { DDRF &= ~(1<<5); PORTF &= ~(1<<5); }
-inline void gh60_esc_led_off(void) { DDRF &= ~(1<<6); PORTF &= ~(1<<6); }
-inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); }
-
-/* GH60 keymap definition macro
- * K2C, K31 and K3C are extra keys for ISO
- */
-#define KEYMAP( \
- K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
- K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
- K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
- K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
- K40, K41, K42, K45, K49, K4A, K4B, K4C, K4D \
-) { \
- { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D }, \
- { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D }, \
- { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D }, \
- { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D }, \
- { KC_##K40, KC_##K41, KC_##K42, KC_NO, KC_NO, KC_##K45, KC_NO, KC_NO, KC_NO, KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D } \
-}
-
-/* ANSI valiant. No extra keys for ISO */
-#define KEYMAP_ANSI( \
- K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
- K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
- K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2D, \
- K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3D, \
- K40, K41, K42, K45, K4A, K4B, K4C, K4D \
-) KEYMAP( \
- K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
- K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
- K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO, K2D, \
- K30, NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, NO, K3D, \
- K40, K41, K42, K45, NO, K4A, K4B, K4C, K4D \
-)
-
-#define KEYMAP_HHKB( \
- K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K49,\
- K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
- K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2D, \
- K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3D, K3C, \
- K40, K41, K42, K45, K4A, K4B, K4C, K4D \
-) KEYMAP( \
- K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
- K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
- K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO, K2D, \
- K30, NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
- K40, K41, K42, K45, K49, K4A, K4B, K4C, K4D \
-)
-
-#endif
+#ifndef GH60_H +#define GH60_H + +#include "quantum.h" +#include "led.h" + +/* GH60 LEDs + * GPIO pads + * 0 F7 WASD LEDs + * 1 F6 ESC LED + * 2 F5 FN LED + * 3 F4 POKER Arrow LEDs + * B2 Capslock LED + * B0 not connected + */ +inline void gh60_caps_led_on(void) { DDRB |= (1<<2); PORTB &= ~(1<<2); } +inline void gh60_poker_leds_on(void) { DDRF |= (1<<4); PORTF &= ~(1<<4); } +inline void gh60_fn_led_on(void) { DDRF |= (1<<5); PORTF &= ~(1<<5); } +inline void gh60_esc_led_on(void) { DDRF |= (1<<6); PORTF &= ~(1<<6); } +inline void gh60_wasd_leds_on(void) { DDRF |= (1<<7); PORTF &= ~(1<<7); } + +inline void gh60_caps_led_off(void) { DDRB &= ~(1<<2); PORTB &= ~(1<<2); } +inline void gh60_poker_leds_off(void) { DDRF &= ~(1<<4); PORTF &= ~(1<<4); } +inline void gh60_fn_led_off(void) { DDRF &= ~(1<<5); PORTF &= ~(1<<5); } +inline void gh60_esc_led_off(void) { DDRF &= ~(1<<6); PORTF &= ~(1<<6); } +inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); } + +/* GH60 keymap definition macro + * K2C, K31 and K3C are extra keys for ISO + */ +#define KEYMAP( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \ + K40, K41, K42, K45, K49, K4A, K4B, K4C, K4D \ +) { \ + { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D }, \ + { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D }, \ + { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D }, \ + { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D }, \ + { KC_##K40, KC_##K41, KC_##K42, KC_NO, KC_NO, KC_##K45, KC_NO, KC_NO, KC_NO, KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D } \ +} + +/* ANSI valiant. No extra keys for ISO */ +#define KEYMAP_ANSI( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2D, \ + K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3D, \ + K40, K41, K42, K45, K4A, K4B, K4C, K4D \ +) KEYMAP( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO, K2D, \ + K30, NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, NO, K3D, \ + K40, K41, K42, K45, NO, K4A, K4B, K4C, K4D \ +) + +#define KEYMAP_HHKB( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K49,\ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2D, \ + K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3D, K3C, \ + K40, K41, K42, K45, K4A, K4B, K4C, K4D \ +) KEYMAP( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO, K2D, \ + K30, NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \ + K40, K41, K42, K45, K49, K4A, K4B, K4C, K4D \ +) + +#endif diff --git a/keyboards/gh60/keymaps/robotmaxtron/Makefile b/keyboards/gh60/keymaps/robotmaxtron/Makefile index 2e69aee298..c73cf11417 100644 --- a/keyboards/gh60/keymaps/robotmaxtron/Makefile +++ b/keyboards/gh60/keymaps/robotmaxtron/Makefile @@ -1,112 +1,112 @@ -#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-# Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-# (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-# have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-# have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-# (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-# (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging,
-# with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-# bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-# CONSOLE_ENABLE ?= yes # Console for debug(+400)
-# COMMAND_ENABLE ?= yes # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-# MIDI_ENABLE ?= YES # MIDI controls
-# UNICODE_ENABLE ?= YES # Unicode
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow
-
-ifndef QUANTUM_DIR
- include ../../../../Makefile
-endif
-
+#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif + diff --git a/keyboards/gh60/keymaps/robotmaxtron/config.h b/keyboards/gh60/keymaps/robotmaxtron/config.h index 8272875ed0..6a29e6b8c2 100644 --- a/keyboards/gh60/keymaps/robotmaxtron/config.h +++ b/keyboards/gh60/keymaps/robotmaxtron/config.h @@ -1,190 +1,190 @@ -/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID 0xFEED
-#define PRODUCT_ID 0x6060
-#define DEVICE_VER 0x0001
-#define MANUFACTURER geekhack
-#define PRODUCT GH60
-#define DESCRIPTION t.m.k. keyboard firmware for GH60
-
-/* key matrix size */
-#define MATRIX_ROWS 5
-#define MATRIX_COLS 14
-
-/*
- * Keyboard Matrix Assignments
- *
- * Change this to how you wired your keyboard
- * COLS: AVR pins used for columns, left to right
- * ROWS: AVR pins used for rows, top to bottom
- * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
- * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
- *
-*/
- #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
-// Rev A
-// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 }
-// Rev B/C
- #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }
-#define UNUSED_PINS
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCING_DELAY 5
-
-/* define if matrix has ghost (lacks anti-ghosting diodes) */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-#define BACKLIGHT_LEVELS 3
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
-//#define FORCE_NKRO
-
-/*
- * Magic Key Options
- *
- * Magic keys are hotkey commands that allow control over firmware functions of
- * the keyboard. They are best used in combination with the HID Listen program,
- * found here: https://www.pjrc.com/teensy/hid_listen.html
- *
- * The options below allow the magic key functionality to be changed. This is
- * useful if your keyboard/keypad is missing keys and you want magic key support.
- *
- */
-
-/* key combination for magic key command */
-#define IS_COMMAND() ( \
- keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-/* control how magic key switches layers */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
-
-/* override magic key keymap */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
-//#define MAGIC_KEY_HELP1 H
-//#define MAGIC_KEY_HELP2 SLASH
-//#define MAGIC_KEY_DEBUG D
-//#define MAGIC_KEY_DEBUG_MATRIX X
-//#define MAGIC_KEY_DEBUG_KBD K
-//#define MAGIC_KEY_DEBUG_MOUSE M
-//#define MAGIC_KEY_VERSION V
-//#define MAGIC_KEY_STATUS S
-//#define MAGIC_KEY_CONSOLE C
-//#define MAGIC_KEY_LAYER0_ALT1 ESC
-//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
-//#define MAGIC_KEY_LAYER0 0
-//#define MAGIC_KEY_LAYER1 1
-//#define MAGIC_KEY_LAYER2 2
-//#define MAGIC_KEY_LAYER3 3
-//#define MAGIC_KEY_LAYER4 4
-//#define MAGIC_KEY_LAYER5 5
-//#define MAGIC_KEY_LAYER6 6
-//#define MAGIC_KEY_LAYER7 7
-//#define MAGIC_KEY_LAYER8 8
-//#define MAGIC_KEY_LAYER9 9
-//#define MAGIC_KEY_BOOTLOADER PAUSE
-//#define MAGIC_KEY_LOCK CAPS
-//#define MAGIC_KEY_EEPROM E
-//#define MAGIC_KEY_NKRO N
-//#define MAGIC_KEY_SLEEP_LED Z
-
-/*
- * Feature disable options
- * These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-//#define NO_DEBUG
-
-/* disable print */
-//#define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-
-/*
- * RGB Underglow
- * These settings are for the F4 by default:
- *
- *
- * #define ws2812_PORTREG PORTF
- * #define ws2812_DDRREG DDRF
- * #define ws2812_pin PF4
- * #define RGBLED_NUM 14 // Number of LEDs
- * #define RGBLIGHT_HUE_STEP 10
- * #define RGBLIGHT_SAT_STEP 17
- * #define RGBLIGHT_VAL_STEP 17
- *
- * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects.
- * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations.
- * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c
-*/
-
-/* Deprecated code below
-#define ws2812_PORTREG PORTF
-#define ws2812_DDRREG DDRF
-#define ws2812_pin PF4
-*/
-#define RGB_DI_PIN F4
-#define RGBLIGHT_TIMER
-#define RGBLED_NUM 8 // Number of LEDs
-#define RGBLIGHT_HUE_STEP 8
-#define RGBLIGHT_SAT_STEP 8
-#define RGBLIGHT_VAL_STEP 8
-#endif
+/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT GH60 +#define DESCRIPTION t.m.k. keyboard firmware for GH60 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ + #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +// Rev A +// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 } +// Rev B/C + #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * RGB Underglow + * These settings are for the F4 by default: + * + * + * #define ws2812_PORTREG PORTF + * #define ws2812_DDRREG DDRF + * #define ws2812_pin PF4 + * #define RGBLED_NUM 14 // Number of LEDs + * #define RGBLIGHT_HUE_STEP 10 + * #define RGBLIGHT_SAT_STEP 17 + * #define RGBLIGHT_VAL_STEP 17 + * + * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. + * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. + * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c +*/ + +/* Deprecated code below +#define ws2812_PORTREG PORTF +#define ws2812_DDRREG DDRF +#define ws2812_pin PF4 +*/ +#define RGB_DI_PIN F4 +#define RGBLIGHT_TIMER +#define RGBLED_NUM 8 // Number of LEDs +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#endif diff --git a/keyboards/gh60/pinout.txt b/keyboards/gh60/pinout.txt index 3787f938e7..e9bf1983a5 100644 --- a/keyboards/gh60/pinout.txt +++ b/keyboards/gh60/pinout.txt @@ -1,18 +1,18 @@ - /* Column pin configuration
- * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13
- * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C)
- */
-
- /* Row pin configuration
- * row: 0 1 2 3 4
- * pin: D0 D1 D2 D3 D5
- */
-
- GPIO pads
- 0 F7 WASD LEDs
- 1 F6 ESC LED
- 2 F5 FN LED
- 3 F4 POKER Arrow LEDs
-
- B2 Capslock LED
+ /* Column pin configuration + * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 + * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C) + */ + + /* Row pin configuration + * row: 0 1 2 3 4 + * pin: D0 D1 D2 D3 D5 + */ + + GPIO pads + 0 F7 WASD LEDs + 1 F6 ESC LED + 2 F5 FN LED + 3 F4 POKER Arrow LEDs + + B2 Capslock LED B0 not connected
\ No newline at end of file diff --git a/keyboards/gh60/readme.md b/keyboards/gh60/readme.md index 92302d507c..ad042483d8 100644 --- a/keyboards/gh60/readme.md +++ b/keyboards/gh60/readme.md @@ -1,60 +1,60 @@ -## gh60 Rev C keyboard firmware
-
-
-
- /* Column pin configuration
- * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13
- * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C)
- */
-
- /* Row pin configuration
- * row: 0 1 2 3 4
- * pin: D0 D1 D2 D3 D5
- */
-
- GPIO pads
- 0 F7 WASD LEDs
- 1 F6 ESC LED
- 2 F5 FN LED
- 3 F4 POKER Arrow LEDs
-
- B2 Capslock LED
- B0 not connected
-
-Functions to controls LED clusters
-
- gh60_caps_led_on()
- gh60_poker_leds_on()
- gh60_fn_led_on()
- gh60_esc_led_on()
- gh60_wasd_leds_on()
-
- gh60_caps_led_off()
- gh60_poker_leds_off()
- gh60_fn_led_off()
- gh60_esc_led_off()
- gh60_wasd_leds_off()
-
-======================
-
-## Quantum MK Firmware
-
-For the full Quantum feature list, see [the parent readme.md](/readme.md).
-
-## Building
-
-Download or clone the whole firmware and navigate to the keyboards/gh60_rev_c folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.
-
-Depending on which keymap you would like to use, you will have to compile slightly differently.
-
-### Default
-To build with the default keymap, simply run `make`.
-
-### Other Keymaps
-Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
-
-To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
-```
-$ make KEYMAP=[default|jack|<name>]
-```
-Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
+## gh60 Rev C keyboard firmware + + + + /* Column pin configuration + * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 + * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C) + */ + + /* Row pin configuration + * row: 0 1 2 3 4 + * pin: D0 D1 D2 D3 D5 + */ + + GPIO pads + 0 F7 WASD LEDs + 1 F6 ESC LED + 2 F5 FN LED + 3 F4 POKER Arrow LEDs + + B2 Capslock LED + B0 not connected + +Functions to controls LED clusters + + gh60_caps_led_on() + gh60_poker_leds_on() + gh60_fn_led_on() + gh60_esc_led_on() + gh60_wasd_leds_on() + + gh60_caps_led_off() + gh60_poker_leds_off() + gh60_fn_led_off() + gh60_esc_led_off() + gh60_wasd_leds_off() + +====================== + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/gh60_rev_c folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. |