diff options
Diffstat (limited to 'keyboards/ergodox_ez/rules.mk')
| -rw-r--r-- | keyboards/ergodox_ez/rules.mk | 84 |
1 files changed, 18 insertions, 66 deletions
diff --git a/keyboards/ergodox_ez/rules.mk b/keyboards/ergodox_ez/rules.mk index 3b9aa3f0a9..9ad4eaa186 100644 --- a/keyboards/ergodox_ez/rules.mk +++ b/keyboards/ergodox_ez/rules.mk @@ -1,64 +1,16 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # If you have Left LEDs (see # https://geekhack.org/index.php?topic=22780.msg873819#msg873819 for # details), include the following define: @@ -67,20 +19,20 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Build Options # comment out to disable the options. # -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDox EZ -NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -UNICODE_ENABLE = yes # Unicode -SWAP_HANDS_ENABLE= yes # Allow swapping hands of keyboard +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = no # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +CUSTOM_MATRIX = lite # Custom matrix file for the ErgoDox EZ +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +UNICODE_ENABLE = yes # Unicode +SWAP_HANDS_ENABLE= yes # Allow swapping hands of keyboard SLEEP_LED_ENABLE = no API_SYSEX_ENABLE = no RGBLIGHT_ENABLE = yes -RGB_MATRIX_ENABLE = no # enable later +RGB_MATRIX_ENABLE = no # enable later DEBOUNCE_TYPE = eager_pr # project specific files |