diff options
Diffstat (limited to 'keyboard/infinity/tool/k20dx32_flash.cfg')
| -rw-r--r-- | keyboard/infinity/tool/k20dx32_flash.cfg | 139 |
1 files changed, 0 insertions, 139 deletions
diff --git a/keyboard/infinity/tool/k20dx32_flash.cfg b/keyboard/infinity/tool/k20dx32_flash.cfg deleted file mode 100644 index 1e3deb0910..0000000000 --- a/keyboard/infinity/tool/k20dx32_flash.cfg +++ /dev/null @@ -1,139 +0,0 @@ -# FreeScale Kinetis K20 devices with 32kB Flash and 8kB Local On-Chip SRAM, -# Nemuisan's Special for MK20DN32VFT5,MK20DX32VFT5,MK10DN32VFT5,MK10DX32VFT5 - - -# 0.8.0 has no these procs -proc using_jtag {} { - set _TRANSPORT [ transport select ] - expr { [ string first "jtag" $_TRANSPORT ] != -1 } -} - -proc using_swd {} { - set _TRANSPORT [ transport select ] - expr { [ string first "swd" $_TRANSPORT ] != -1 } -} - -proc using_hla {} { - set _TRANSPORT [ transport select ] - expr { [ string first "hla" $_TRANSPORT ] != -1 } -} - -source [find target/swj-dp.tcl] - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME k20 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -if { [info exists CPUTAPID] } { - set _CPUTAPID $CPUTAPID -} else { - if { [using_jtag] } { - set _CPUTAPID 0x4BA00477 - } { - # this is the SW-DP tap id not the jtag tap id - set _CPUTAPID 0x2BA01477 - } -} - -# Work-area is a space in RAM used for flash programming -# By default use 8kB -if { [info exists WORKAREASIZE] == 0 } { - set _WORKAREASIZE 0x2000 -} - -# Select "srst_only", Nemuisan said so! -echo "Kinetis MUST need Hardware SRST Control to Recover Secure-State!" -adapter_nsrst_delay 200 -reset_config srst_only - -swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID -set _TARGETNAME $_CHIPNAME.cpu -target create $_TARGETNAME cortex_m -chain-position $_TARGETNAME - -# It is important that "kinetis mdm check_security" is called for -# 'examine-end' event and not 'eximine-start'. Calling it in 'examine-start' -# causes "kinetis mdm check_security" to fail the first time openocd -# calls it when it tries to connect after the CPU has been power-cycled. -$_CHIPNAME.cpu configure -event examine-end { - kinetis mdm check_security -# Uncomment when gone into s*ck'n secured state! -# kinetis mdm mass_erase -} - -# K20 has minimun 8kB of SRAM and starts at 1FFFF000. -$_TARGETNAME configure -work-area-phys 0x1FFFF000 -work-area-size $_WORKAREASIZE -work-area-backup 0 -rtos auto - -# MK20DN32VFT5,MK20DX32VFT5,MK10DN32VFT5,MK10DX32VFT5 has 32kB of flash memory. -flash bank $_CHIPNAME.pflash kinetis 0x00000000 0x8000 0 4 $_TARGETNAME - - -proc mt_flash {IMGFILE} { - flash write_image erase $IMGFILE - reset run - halt - verify_image $IMGFILE - reset run - shutdown -} - -proc mt_flash_bin {IMGFILE OFFSET} { - flash write_image erase $IMGFILE $OFFSET bin - reset run - halt - verify_image $IMGFILE $OFFSET bin - reset run - shutdown -} - -proc mt_flash_hex {IMGFILE} { - flash write_image erase $IMGFILE 0 ihex - reset run - halt - verify_image $IMGFILE 0 ihex - reset run - shutdown -} - -proc mt_flash_srec {IMGFILE} { - flash write_image erase $IMGFILE 0 s19 - reset run - halt - verify_image $IMGFILE 0 s19 - reset run - shutdown -} - -proc mass_erase {} { - kinetis mdm mass_erase -} - -proc eraser {} { -# Verbose procedure confirmed erase routine - flash info 0 -# CAUTION! "flash erase_sector 0 0 last" goes into secure state!!! -# USE "mass_erase" command instead of -# flash erase_sector 0 0 last - mass_erase - shutdown -} - -#debug_level 3 -# HLA doesn't have cortex_m commands -if {![using_hla]} { - # if srst is not fitted use SYSRESETREQ to - # perform a soft reset - cortex_m reset_config sysresetreq -} -adapter_khz 1000 -reset_config srst_only srst_nogate connect_assert_srst -gdb_target_description disable -init -reset init |