summaryrefslogtreecommitdiff
path: root/docs/feature_pointing_device.md
diff options
context:
space:
mode:
Diffstat (limited to 'docs/feature_pointing_device.md')
-rw-r--r--docs/feature_pointing_device.md159
1 files changed, 138 insertions, 21 deletions
diff --git a/docs/feature_pointing_device.md b/docs/feature_pointing_device.md
index 098a787ed8..5f1260eede 100644
--- a/docs/feature_pointing_device.md
+++ b/docs/feature_pointing_device.md
@@ -30,7 +30,7 @@ The ADNS 5050 sensor uses a serial type protocol for communication, and requires
The CPI range is 125-1375, in increments of 125. Defaults to 500 CPI.
-### ADSN 9800 Sensor
+### ADNS 9800 Sensor
To use the ADNS 9800 sensor, add this to your `rules.mk`
@@ -69,7 +69,7 @@ The Analog Joystick is an analog (ADC) driven sensor. There are a variety of jo
|`ANALOG_JOYSTICK_AXIS_MAX` | (Optional) Sets the upper range to be considered movement. | `1023` |
|`ANALOG_JOYSTICK_SPEED_REGULATOR` | (Optional) The divisor used to slow down movement. (lower makes it faster) | `20` |
|`ANALOG_JOYSTICK_READ_INTERVAL` | (Optional) The interval in milliseconds between reads. | `10` |
-|`ANALOG_JOYSTICK_SPEED_MAX` | (Optional) The maxiumum value used for motion. | `2` |
+|`ANALOG_JOYSTICK_SPEED_MAX` | (Optional) The maximum value used for motion. | `2` |
|`ANALOG_JOYSTICK_CLICK_PIN` | (Optional) The pin wired up to the press switch of the analog stick. | _not defined_ |
@@ -127,11 +127,10 @@ The Pimoroni Trackball module is a I2C based breakout board with an RGB enable t
| Setting | Description | Default |
|-------------------------------------|------------------------------------------------------------------------------------|---------|
|`PIMORONI_TRACKBALL_ADDRESS` | (Required) Sets the I2C Address for the Pimoroni Trackball. | `0x0A` |
-|`PIMORONI_TRACKBALL_TIMEOUT` | (Optional) The timeout for i2c communication with the trackpad in milliseconds. | `100` |
-|`PIMORONI_TRACKBALL_INTERVAL_MS` | (Optional) The update/read interval for the sensor in milliseconds. | `8` |
+|`PIMORONI_TRACKBALL_TIMEOUT` | (Optional) The timeout for i2c communication with the trackball in milliseconds. | `100` |
|`PIMORONI_TRACKBALL_SCALE` | (Optional) The multiplier used to generate reports from the sensor. | `5` |
|`PIMORONI_TRACKBALL_DEBOUNCE_CYCLES` | (Optional) The number of scan cycles used for debouncing on the ball press. | `20` |
-|`PIMORONI_TRACKBALL_ERROR_COUNT` | (Optional) Specifies the number of read/write errors until the sensor is disabled. | `10` |
+|`PIMORONI_TRACKBALL_ERROR_COUNT` | (Optional) Specifies the number of read/write errors until the sensor is disabled. | `10` |
### PMW 3360 Sensor
@@ -145,16 +144,39 @@ The PMW 3360 is an SPI driven optical sensor, that uses a built in IR LED for su
| Setting | Description | Default |
|-----------------------------|--------------------------------------------------------------------------------------------|---------------|
-|`PMW3360_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
-|`PMW3360_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `2000000` |
-|`PMW3360_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` |
-|`PMW3360_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `3` |
-|`PMW3360_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
-|`PMW3360_LIFTOFF_DISTANCE` | (Optional) Sets the lift off distance at run time | `0x02` |
-|`ROTATIONAL_TRANSFORM_ANGLE` | (Optional) Allows for the sensor data to be rotated +/- 30 degrees directly in the sensor. | `0` |
+|`PMW3360_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
+|`PMW3360_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `2000000` |
+|`PMW3360_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` |
+|`PMW3360_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `3` |
+|`PMW3360_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
+|`PMW3360_LIFTOFF_DISTANCE` | (Optional) Sets the lift off distance at run time | `0x02` |
+|`ROTATIONAL_TRANSFORM_ANGLE` | (Optional) Allows for the sensor data to be rotated +/- 127 degrees directly in the sensor. | `0` |
+|`PMW3360_LEGACY_FIRMWARE_UPLOAD` | (Optional) Switches to older, manual upload of firmware, for compatibility. | _not defined_ |
The CPI range is 100-12000, in increments of 100. Defaults to 1600 CPI.
+### PMW 3389 Sensor
+
+To use the PMW 3389 sensor, add this to your `rules.mk`
+
+```make
+POINTING_DEVICE_DRIVER = pmw3389
+```
+
+The PMW 3389 is an SPI driven optical sensor, that uses a built in IR LED for surface tracking.
+
+| Setting | Description | Default |
+|---------------------------------|--------------------------------------------------------------------------------------------|---------------|
+|`PMW3389_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
+|`PMW3389_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `2000000` |
+|`PMW3389_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` |
+|`PMW3389_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `3` |
+|`PMW3389_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
+|`PMW3389_LIFTOFF_DISTANCE` | (Optional) Sets the lift off distance at run time | `0x02` |
+|`ROTATIONAL_TRANSFORM_ANGLE` | (Optional) Allows for the sensor data to be rotated +/- 30 degrees directly in the sensor. | `0` |
+
+The CPI range is 50-16000, in increments of 50. Defaults to 2000 CPI.
+
### Custom Driver
@@ -171,14 +193,35 @@ void pointing_device_driver_set_cpi(uint16_t cpi) {}
## Common Configuration
-| Setting | Description | Default |
-|-------------------------------|-----------------------------------------------------------------------|---------------|
-|`POINTING_DEVICE_ROTATION_90` | (Optional) Rotates the X and Y data by 90 degrees. | _not defined_ |
-|`POINTING_DEVICE_ROTATION_180` | (Optional) Rotates the X and Y data by 180 degrees. | _not defined_ |
-|`POINTING_DEVICE_ROTATION_270` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ |
-|`POINTING_DEVICE_INVERT_X` | (Optional) Inverts the X axis report. | _not defined_ |
-|`POINTING_DEVICE_INVERT_Y` | (Optional) Inverts the Y axis report. | _not defined_ |
-|`POINTING_DEVICE_MOTION_PIN` | (Optional) If supported, will only read from sensor if pin is active. | _not defined_ |
+| Setting | Description | Default |
+|----------------------------------|-----------------------------------------------------------------------|-------------------|
+|`POINTING_DEVICE_ROTATION_90` | (Optional) Rotates the X and Y data by 90 degrees. | _not defined_ |
+|`POINTING_DEVICE_ROTATION_180` | (Optional) Rotates the X and Y data by 180 degrees. | _not defined_ |
+|`POINTING_DEVICE_ROTATION_270` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ |
+|`POINTING_DEVICE_INVERT_X` | (Optional) Inverts the X axis report. | _not defined_ |
+|`POINTING_DEVICE_INVERT_Y` | (Optional) Inverts the Y axis report. | _not defined_ |
+|`POINTING_DEVICE_MOTION_PIN` | (Optional) If supported, will only read from sensor if pin is active. | _not defined_ |
+|`POINTING_DEVICE_TASK_THROTTLE_MS` | (Optional) Limits the frequency that the sensor is polled for motion. | _not defined_ |
+
+!> When using `SPLIT_POINTING_ENABLE` the `POINTING_DEVICE_MOTION_PIN` functionality is not supported and would recommend `POINTING_DEVICE_TASK_THROTTLE_MS` be set to `1`. Increasing this value will increase transport performance at the cost of possible mouse responsiveness.
+
+
+## Split Keyboard Configuration
+
+The following configuration options are only available when using `SPLIT_POINTING_ENABLE` see [data sync options](feature_split_keyboard.md?id=data-sync-options). The rotation and invert `*_RIGHT` options are only used with `POINTING_DEVICE_COMBINED`. If using `POINTING_DEVICE_LEFT` or `POINTING_DEVICE_RIGHT` use the common configuration above to configure your pointing device.
+
+| Setting | Description | Default |
+|----------------------------------------|-----------------------------------------------------------------------|---------------|
+|`POINTING_DEVICE_LEFT` | Pointing device on the left side (Required - pick one only) | _not defined_ |
+|`POINTING_DEVICE_RIGHT` | Pointing device on the right side (Required - pick one only) | _not defined_ |
+|`POINTING_DEVICE_COMBINED` | Pointing device on both sides (Required - pick one only) | _not defined_ |
+|`POINTING_DEVICE_ROTATION_90_RIGHT` | (Optional) Rotates the X and Y data by 90 degrees. | _not defined_ |
+|`POINTING_DEVICE_ROTATION_180_RIGHT` | (Optional) Rotates the X and Y data by 180 degrees. | _not defined_ |
+|`POINTING_DEVICE_ROTATION_270_RIGHT` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ |
+|`POINTING_DEVICE_INVERT_X_RIGHT` | (Optional) Inverts the X axis report. | _not defined_ |
+|`POINTING_DEVICE_INVERT_Y_RIGHT` | (Optional) Inverts the Y axis report. | _not defined_ |
+
+!> If there is a `_RIGHT` configuration option or callback, the [common configuration](feature_pointing_device.md?id=common-configuration) option will work for the left. For correct left/right detection you should setup a [handedness option](feature_split_keyboard?id=setting-handedness), `EE_HANDS` is usually a good option for an existing board that doesn't do handedness by hardware.
## Callbacks and Functions
@@ -188,7 +231,7 @@ void pointing_device_driver_set_cpi(uint16_t cpi) {}
| `pointing_device_init_kb(void)` | Callback to allow for keyboard level initialization. Useful for additional hardware sensors. |
| `pointing_device_init_user(void)` | Callback to allow for user level initialization. Useful for additional hardware sensors. |
| `pointing_device_task_kb(mouse_report)` | Callback that sends sensor data, so keyboard code can intercept and modify the data. Returns a mouse report. |
-| `pointing_device_task_user(mouse_report)` | Callback that sends sensor data, so user coe can intercept and modify the data. Returns a mouse report. |
+| `pointing_device_task_user(mouse_report)` | Callback that sends sensor data, so user code can intercept and modify the data. Returns a mouse report. |
| `pointing_device_handle_buttons(buttons, pressed, button)` | Callback to handle hardware button presses. Returns a `uint8_t`. |
| `pointing_device_get_cpi(void)` | Gets the current CPI/DPI setting from the sensor, if supported. |
| `pointing_device_set_cpi(uint16_t)` | Sets the CPI/DPI, if supported. |
@@ -196,6 +239,21 @@ void pointing_device_driver_set_cpi(uint16_t cpi) {}
| `pointing_device_set_report(mouse_report)` | Sets the mouse report to the assigned `mouse_report_t` data structured passed to the function. |
| `pointing_device_send(void)` | Sends the current mouse report to the host system. Function can be replaced. |
| `has_mouse_report_changed(old, new)` | Compares the old and new `mouse_report_t` data and returns true only if it has changed. |
+| `pointing_device_adjust_by_defines(mouse_report)` | Applies rotations and invert configurations to a raw mouse report. |
+
+
+## Split Keyboard Callbacks and Functions
+
+The combined functions below are only available when using `SPLIT_POINTING_ENABLE` and `POINTING_DEVICE_COMBINED`. The 2 callbacks `pointing_device_task_combined_*` replace the single sided equivalents above. See the [combined pointing devices example](feature_pointing_device.md?id=combined-pointing-devices)
+
+| Function | Description |
+|-----------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------------|
+| `pointing_device_set_shared_report(mouse_report)` | Sets the shared mouse report to the assigned `mouse_report_t` data structured passed to the function. |
+| `pointing_device_set_cpi_on_side(bool, uint16_t)` | Sets the CPI/DPI of one side, if supported. Passing `true` will set the left and `false` the right` |
+| `pointing_device_combine_reports(left_report, right_report)` | Returns a combined mouse_report of left_report and right_report (as a `mouse_report_t` data structure) |
+| `pointing_device_task_combined_kb(left_report, right_report)` | Callback, so keyboard code can intercept and modify the data. Returns a combined mouse report. |
+| `pointing_device_task_combined_user(left_report, right_report)` | Callback, so user code can intercept and modify. Returns a combined mouse report using `pointing_device_combine_reports` |
+| `pointing_device_adjust_by_defines_right(mouse_report)` | Applies right side rotations and invert configurations to a raw mouse report. |
# Manipulating Mouse Reports
@@ -274,3 +332,62 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
```
This allows you to toggle between scrolling and cursor movement by pressing the DRAG_SCROLL key.
+
+## Split Examples
+
+The following examples make use the `SPLIT_POINTING_ENABLE` functionality and show how to manipulate the mouse report for a scrolling mode.
+
+### Single Pointing Device
+
+The following example will work with either `POINTING_DEVICE_LEFT` or `POINTING_DEVICE_RIGHT` and enables scrolling mode while on a particular layer.
+
+```c
+
+static bool scrolling_mode = false;
+
+layer_state_t layer_state_set_user(layer_state_t state) {
+ switch (get_highest_layer(state)) {
+ case _RAISE: // If we're on the _RAISE layer enable scrolling mode
+ scrolling_mode = true;
+ pointing_device_set_cpi(2000);
+ break;
+ default:
+ if (scrolling_mode) { // check if we were scrolling before and set disable if so
+ scrolling_mode = false;
+ pointing_device_set_cpi(8000);
+ }
+ break;
+ }
+ return state;
+}
+
+report_mouse_t pointing_device_task_user(report_mouse_t mouse_report) {
+ if (scrolling_mode) {
+ mouse_report.h = mouse_report.x;
+ mouse_report.v = mouse_report.y;
+ mouse_report.x = 0;
+ mouse_report.y = 0;
+ }
+ return mouse_report;
+}
+```
+
+### Combined Pointing Devices
+
+The following example requires `POINTING_DEVICE_COMBINED` and sets the left side pointing device to scroll only.
+
+```c
+void keyboard_post_init_user(void) {
+ pointing_device_set_cpi_on_side(true, 1000); //Set cpi on left side to a low value for slower scrolling.
+ pointing_device_set_cpi_on_side(false, 8000); //Set cpi on right side to a reasonable value for mousing.
+}
+
+report_mouse_t pointing_device_task_combined_user(report_mouse_t left_report, report_mouse_t right_report) {
+ left_report.h = left_report.x;
+ left_report.v = left_report.y;
+ left_report.x = 0;
+ left_report.y = 0;
+ return pointing_device_combine_reports(left_report, right_report);
+}
+```
+=======