diff options
Diffstat (limited to 'Makefile.hhkb')
| -rw-r--r-- | Makefile.hhkb | 620 |
1 files changed, 620 insertions, 0 deletions
diff --git a/Makefile.hhkb b/Makefile.hhkb new file mode 100644 index 0000000000..fbf7ede2ee --- /dev/null +++ b/Makefile.hhkb @@ -0,0 +1,620 @@ +# Hey Emacs, this is a -*- makefile -*- +#---------------------------------------------------------------------------- +# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al. +# +# Released to the Public Domain +# +# Additional material for this makefile was written by: +# Peter Fleury +# Tim Henigan +# Colin O'Flynn +# Reiner Patommel +# Markus Pfaff +# Sander Pool +# Frederik Rouleau +# Carlos Lamas +# +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device, using avrdude. +# Please customize the avrdude settings below first! +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + + +# Target file name (without extension). +TARGET = tmk_hhkb + + +# List C source files here. (C dependencies are automatically generated.) +SRC = tmk.c \ + usb.c \ + usb_keyboard.c \ + usb_mouse.c \ + usb_debug.c \ + keymap_hhkb.c \ + matrix_hhkb.c \ + jump_bootloader.c \ + print.c + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +#MCU = at90usb162 # Teensy 1.0 +#MCU = atmega32u4 # Teensy 2.0 +#MCU = at90usb646 # Teensy++ 1.0 +MCU = at90usb1286 # Teensy++ 2.0 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 16000000 + + +# Output format. (can be srec, ihex, binary) +FORMAT = ihex + + +# Object files directory +# To put object files in current directory, use a dot (.), do NOT make +# this an empty or blank macro! +OBJDIR = . + + +# List C++ source files here. (C dependencies are automatically generated.) +CPPSRC = + + +# List Assembler source files here. +# Make them always end in a capital .S. Files ending in a lowercase .s +# will not be considered source files but generated files (assembler +# output from the compiler), and will be deleted upon "make clean"! +# Even though the DOS/Win* filesystem matches both .s and .S the same, +# it will preserve the spelling of the filenames, and gcc itself does +# care about how the name is spelled on its command-line. +ASRC = + + +# Optimization level, can be [0, 1, 2, 3, s]. +# 0 = turn off optimization. s = optimize for size. +# (Note: 3 is not always the best optimization level. See avr-libc FAQ.) +OPT = s + + +# Debugging format. +# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs. +# AVR Studio 4.10 requires dwarf-2. +# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run. +DEBUG = dwarf-2 + + +# List any extra directories to look for include files here. +# Each directory must be seperated by a space. +# Use forward slashes for directory separators. +# For a directory that has spaces, enclose it in quotes. +EXTRAINCDIRS = + + +# Compiler flag to set the C Standard level. +# c89 = "ANSI" C +# gnu89 = c89 plus GCC extensions +# c99 = ISO C99 standard (not yet fully implemented) +# gnu99 = c99 plus GCC extensions +CSTANDARD = -std=gnu99 + + +# Place -D or -U options here for C sources +CDEFS = -DF_CPU=$(F_CPU)UL + + +# Place -D or -U options here for ASM sources +ADEFS = -DF_CPU=$(F_CPU) + + +# Place -D or -U options here for C++ sources +CPPDEFS = -DF_CPU=$(F_CPU)UL +#CPPDEFS += -D__STDC_LIMIT_MACROS +#CPPDEFS += -D__STDC_CONSTANT_MACROS + + + +#---------------- Compiler Options C ---------------- +# -g*: generate debugging information +# -O*: optimization level +# -f...: tuning, see GCC manual and avr-libc documentation +# -Wall...: warning level +# -Wa,...: tell GCC to pass this to the assembler. +# -adhlns...: create assembler listing +CFLAGS = -g$(DEBUG) +CFLAGS += $(CDEFS) +CFLAGS += -O$(OPT) +CFLAGS += -funsigned-char +CFLAGS += -funsigned-bitfields +CFLAGS += -ffunction-sections +CFLAGS += -fpack-struct +CFLAGS += -fshort-enums +CFLAGS += -Wall +CFLAGS += -Wstrict-prototypes +#CFLAGS += -mshort-calls +#CFLAGS += -fno-unit-at-a-time +#CFLAGS += -Wundef +#CFLAGS += -Wunreachable-code +#CFLAGS += -Wsign-compare +CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst) +CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS)) +CFLAGS += $(CSTANDARD) + + +#---------------- Compiler Options C++ ---------------- +# -g*: generate debugging information +# -O*: optimization level +# -f...: tuning, see GCC manual and avr-libc documentation +# -Wall...: warning level +# -Wa,...: tell GCC to pass this to the assembler. +# -adhlns...: create assembler listing +CPPFLAGS = -g$(DEBUG) +CPPFLAGS += $(CPPDEFS) +CPPFLAGS += -O$(OPT) +CPPFLAGS += -funsigned-char +CPPFLAGS += -funsigned-bitfields +CPPFLAGS += -fpack-struct +CPPFLAGS += -fshort-enums +CPPFLAGS += -fno-exceptions +CPPFLAGS += -Wall +CPPFLAGS += -Wundef +#CPPFLAGS += -mshort-calls +#CPPFLAGS += -fno-unit-at-a-time +#CPPFLAGS += -Wstrict-prototypes +#CPPFLAGS += -Wunreachable-code +#CPPFLAGS += -Wsign-compare +CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst) +CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS)) +#CPPFLAGS += $(CSTANDARD) + + +#---------------- Assembler Options ---------------- +# -Wa,...: tell GCC to pass this to the assembler. +# -adhlns: create listing +# -gstabs: have the assembler create line number information; note that +# for use in COFF files, additional information about filenames +# and function names needs to be present in the assembler source +# files -- see avr-libc docs [FIXME: not yet described there] +# -listing-cont-lines: Sets the maximum number of continuation lines of hex +# dump that will be displayed for a given single line of source input. +ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100 + + +#---------------- Library Options ---------------- +# Minimalistic printf version +PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min + +# Floating point printf version (requires MATH_LIB = -lm below) +PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt + +# If this is left blank, then it will use the Standard printf version. +PRINTF_LIB = +#PRINTF_LIB = $(PRINTF_LIB_MIN) +#PRINTF_LIB = $(PRINTF_LIB_FLOAT) + + +# Minimalistic scanf version +SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min + +# Floating point + %[ scanf version (requires MATH_LIB = -lm below) +SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt + +# If this is left blank, then it will use the Standard scanf version. +SCANF_LIB = +#SCANF_LIB = $(SCANF_LIB_MIN) +#SCANF_LIB = $(SCANF_LIB_FLOAT) + + +MATH_LIB = -lm + + +# List any extra directories to look for libraries here. +# Each directory must be seperated by a space. +# Use forward slashes for directory separators. +# For a directory that has spaces, enclose it in quotes. +EXTRALIBDIRS = + + + +#---------------- External Memory Options ---------------- + +# 64 KB of external RAM, starting after internal RAM (ATmega128!), +# used for variables (.data/.bss) and heap (malloc()). +#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff + +# 64 KB of external RAM, starting after internal RAM (ATmega128!), +# only used for heap (malloc()). +#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff + +EXTMEMOPTS = + + + +#---------------- Linker Options ---------------- +# -Wl,...: tell GCC to pass this to linker. +# -Map: create map file +# --cref: add cross reference to map file +LDFLAGS = -Wl,-Map=$(TARGET).map,--cref +LDFLAGS += -Wl,--relax +LDFLAGS += -Wl,--gc-sections +LDFLAGS += $(EXTMEMOPTS) +LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS)) +LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB) +#LDFLAGS += -T linker_script.x + + + +#---------------- Programming Options (avrdude) ---------------- + +# Programming hardware +# Type: avrdude -c ? +# to get a full listing. +# +AVRDUDE_PROGRAMMER = stk500v2 + +# com1 = serial port. Use lpt1 to connect to parallel port. +AVRDUDE_PORT = com1 # programmer connected to serial device + +AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex +#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep + + +# Uncomment the following if you want avrdude's erase cycle counter. +# Note that this counter needs to be initialized first using -Yn, +# see avrdude manual. +#AVRDUDE_ERASE_COUNTER = -y + +# Uncomment the following if you do /not/ wish a verification to be +# performed after programming the device. +#AVRDUDE_NO_VERIFY = -V + +# Increase verbosity level. Please use this when submitting bug +# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> +# to submit bug reports. +#AVRDUDE_VERBOSE = -v -v + +AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) +AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) +AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) +AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) + + + +#---------------- Debugging Options ---------------- + +# For simulavr only - target MCU frequency. +DEBUG_MFREQ = $(F_CPU) + +# Set the DEBUG_UI to either gdb or insight. +# DEBUG_UI = gdb +DEBUG_UI = insight + +# Set the debugging back-end to either avarice, simulavr. +DEBUG_BACKEND = avarice +#DEBUG_BACKEND = simulavr + +# GDB Init Filename. +GDBINIT_FILE = __avr_gdbinit + +# When using avarice settings for the JTAG +JTAG_DEV = /dev/com1 + +# Debugging port used to communicate between GDB / avarice / simulavr. +DEBUG_PORT = 4242 + +# Debugging host used to communicate between GDB / avarice / simulavr, normally +# just set to localhost unless doing some sort of crazy debugging when +# avarice is running on a different computer. +DEBUG_HOST = localhost + + + +#============================================================================ + + +# Define programs and commands. +SHELL = sh +CC = avr-gcc +OBJCOPY = avr-objcopy +OBJDUMP = avr-objdump +SIZE = avr-size +AR = avr-ar rcs +NM = avr-nm +AVRDUDE = avrdude +REMOVE = rm -f +REMOVEDIR = rm -rf +COPY = cp +WINSHELL = cmd + + +# Define Messages +# English +MSG_ERRORS_NONE = Errors: none +MSG_BEGIN = -------- begin -------- +MSG_END = -------- end -------- +MSG_SIZE_BEFORE = Size before: +MSG_SIZE_AFTER = Size after: +MSG_COFF = Converting to AVR COFF: +MSG_EXTENDED_COFF = Converting to AVR Extended COFF: +MSG_FLASH = Creating load file for Flash: +MSG_EEPROM = Creating load file for EEPROM: +MSG_EXTENDED_LISTING = Creating Extended Listing: +MSG_SYMBOL_TABLE = Creating Symbol Table: +MSG_LINKING = Linking: +MSG_COMPILING = Compiling C: +MSG_COMPILING_CPP = Compiling C++: +MSG_ASSEMBLING = Assembling: +MSG_CLEANING = Cleaning project: +MSG_CREATING_LIBRARY = Creating library: + + + + +# Define all object files. +OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o) + +# Define all listing files. +LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst) + + +# Compiler flags to generate dependency files. +GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d + + +# Combine all necessary flags and optional flags. +# Add target processor to flags. +ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS) +ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS) +ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) + + + + + +# Default target. +all: begin gccversion sizebefore build sizeafter end + +# Change the build target to build a HEX file or a library. +build: elf hex eep lss sym +#build: lib + + +elf: $(TARGET).elf +hex: $(TARGET).hex +eep: $(TARGET).eep +lss: $(TARGET).lss +sym: $(TARGET).sym +LIBNAME=lib$(TARGET).a +lib: $(LIBNAME) + + + +# Eye candy. +# AVR Studio 3.x does not check make's exit code but relies on +# the following magic strings to be generated by the compile job. +begin: + @echo + @echo $(MSG_BEGIN) + +end: + @echo $(MSG_END) + @echo + + +# Display size of file. +HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex +#ELFSIZE = $(SIZE) --mcu=$(MCU) --format=avr $(TARGET).elf +ELFSIZE = $(SIZE) $(TARGET).elf + +sizebefore: + @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \ + 2>/dev/null; echo; fi + +sizeafter: + @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \ + 2>/dev/null; echo; fi + + + +# Display compiler version information. +gccversion : + @$(CC) --version + + + +# Program the device. +program: $(TARGET).hex $(TARGET).eep + $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) + + +# Generate avr-gdb config/init file which does the following: +# define the reset signal, load the target file, connect to target, and set +# a breakpoint at main(). +gdb-config: + @$(REMOVE) $(GDBINIT_FILE) + @echo define reset >> $(GDBINIT_FILE) + @echo SIGNAL SIGHUP >> $(GDBINIT_FILE) + @echo end >> $(GDBINIT_FILE) + @echo file $(TARGET).elf >> $(GDBINIT_FILE) + @echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE) +ifeq ($(DEBUG_BACKEND),simulavr) + @echo load >> $(GDBINIT_FILE) +endif + @echo break main >> $(GDBINIT_FILE) + +debug: gdb-config $(TARGET).elf +ifeq ($(DEBUG_BACKEND), avarice) + @echo Starting AVaRICE - Press enter when "waiting to connect" message displays. + @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \ + $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT) + @$(WINSHELL) /c pause + +else + @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \ + $(DEBUG_MFREQ) --port $(DEBUG_PORT) +endif + @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE) + + + + +# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. +COFFCONVERT = $(OBJCOPY) --debugging +COFFCONVERT += --change-section-address .data-0x800000 +COFFCONVERT += --change-section-address .bss-0x800000 +COFFCONVERT += --change-section-address .noinit-0x800000 +COFFCONVERT += --change-section-address .eeprom-0x810000 + + + +coff: $(TARGET).elf + @echo + @echo $(MSG_COFF) $(TARGET).cof + $(COFFCONVERT) -O coff-avr $< $(TARGET).cof + + +extcoff: $(TARGET).elf + @echo + @echo $(MSG_EXTENDED_COFF) $(TARGET).cof + $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof + + + +# Create final output files (.hex, .eep) from ELF output file. +%.hex: %.elf + @echo + @echo $(MSG_FLASH) $@ + $(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock -R .signature $< $@ + +%.eep: %.elf + @echo + @echo $(MSG_EEPROM) $@ + -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ + --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0 + +# Create extended listing file from ELF output file. +%.lss: %.elf + @echo + @echo $(MSG_EXTENDED_LISTING) $@ + $(OBJDUMP) -h -S -z $< > $@ + +# Create a symbol table from ELF output file. +%.sym: %.elf + @echo + @echo $(MSG_SYMBOL_TABLE) $@ + $(NM) -n $< > $@ + + + +# Create library from object files. +.SECONDARY : $(TARGET).a +.PRECIOUS : $(OBJ) +%.a: $(OBJ) + @echo + @echo $(MSG_CREATING_LIBRARY) $@ + $(AR) $@ $(OBJ) + + +# Link: create ELF output file from object files. +.SECONDARY : $(TARGET).elf +.PRECIOUS : $(OBJ) +%.elf: $(OBJ) + @echo + @echo $(MSG_LINKING) $@ + $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS) + + +# Compile: create object files from C source files. +$(OBJDIR)/%.o : %.c + @echo + @echo $(MSG_COMPILING) $< + $(CC) -c $(ALL_CFLAGS) $< -o $@ + + +# Compile: create object files from C++ source files. +$(OBJDIR)/%.o : %.cpp + @echo + @echo $(MSG_COMPILING_CPP) $< + $(CC) -c $(ALL_CPPFLAGS) $< -o $@ + + +# Compile: create assembler files from C source files. +%.s : %.c + $(CC) -S $(ALL_CFLAGS) $< -o $@ + + +# Compile: create assembler files from C++ source files. +%.s : %.cpp + $(CC) -S $(ALL_CPPFLAGS) $< -o $@ + + +# Assemble: create object files from assembler source files. +$(OBJDIR)/%.o : %.S + @echo + @echo $(MSG_ASSEMBLING) $< + $(CC) -c $(ALL_ASFLAGS) $< -o $@ + + +# Create preprocessed source for use in sending a bug report. +%.i : %.c + $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@ + + +# Target: clean project. +clean: begin clean_list end + +clean_list : + @echo + @echo $(MSG_CLEANING) + $(REMOVE) $(TARGET).hex + $(REMOVE) $(TARGET).eep + $(REMOVE) $(TARGET).cof + $(REMOVE) $(TARGET).elf + $(REMOVE) $(TARGET).map + $(REMOVE) $(TARGET).sym + $(REMOVE) $(TARGET).lss + $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) + $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) + $(REMOVE) $(SRC:.c=.s) + $(REMOVE) $(SRC:.c=.d) + $(REMOVE) $(SRC:.c=.i) + $(REMOVEDIR) .dep + + +# Create object files directory +$(shell mkdir $(OBJDIR) 2>/dev/null) + + +# Include the dependency files. +-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*) + + +# Listing of phony targets. +.PHONY : all begin finish end sizebefore sizeafter gccversion \ +build elf hex eep lss sym coff extcoff \ +clean clean_list program debug gdb-config |