Add support to XD60 Rev3 (#4938)

* Add preliminary support to XD60 Rev3 PCB (Supports the 12 underglow LEDs, but split spacebar still not wired/implemented).

* * xd60_rev3 folder removed
* xd60 rev2 and rev3 added
* ifndef replaced with pragma once at rev3 config.h

* Readme updated

* new updated statement at keyboards/xd60/readme.md

Co-Authored-By: rodrigofeijao <hello@rodrigofeijao.com>

* Update keyboards/xd60/readme.md

Co-Authored-By: rodrigofeijao <hello@rodrigofeijao.com>

* Update keyboards/xd60/readme.md

Co-Authored-By: rodrigofeijao <hello@rodrigofeijao.com>

* Update keyboards/xd60/readme.md

Co-Authored-By: rodrigofeijao <hello@rodrigofeijao.com>

* Update keyboards/xd60/readme.md

Co-Authored-By: rodrigofeijao <hello@rodrigofeijao.com>

* * XXXXX removed and replaced with 7X
* removed unecessary declarations

* Update keyboards/xd60/keymaps/styr/keymap.c

Co-Authored-By: rodrigofeijao <hello@rodrigofeijao.com>

* action_layer.h include removed

* * action_get_macro removed
* IS_COMMAND() removed
* BOOTLOADER defined

1 files changed, 0 insertions, 67 deletions

diff --git a/keyboards/xd60/rules.mk b/keyboards/xd60/rules.mk
deleted file mode 100644
index 8a60252dcf..0000000000
--- a/keyboards/xd60/rules.mk
+++ /dev/null
@@ -1,67 +0,0 @@
-# MCU name
-# MCU = at90usb1287
-MCU = atmega32u4
-
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-# LUFA specific
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = no         # Commands for debug and configuration
-NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = no           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight. 
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-
-LAYOUTS = 60_ansi
\ No newline at end of file