remove all keyboards but ergodox and planck

2 files changed, 0 insertions, 138 deletions

diff --git a/keyboards/xd60/rev3/config.h b/keyboards/xd60/rev3/config.h
deleted file mode 100644
index d88330cf7b..0000000000
--- a/keyboards/xd60/rev3/config.h
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
-Copyright 2019 Rodrigo Feijao <hello@rodrigofeijao.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#pragma once
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6363
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    XIUDI
-#define PRODUCT         XD60rev3
-#define DESCRIPTION     XD60 rev3 Keyboard PCB by XIUDI
-
-/* key matrix size */
-#define MATRIX_ROWS 5
-#define MATRIX_COLS 14
-
-/*
- * Keyboard Matrix Assignments
- *
- * Change this to how you wired your keyboard
- * COLS: AVR pins used for columns, left to right
- * ROWS: AVR pins used for rows, top to bottom
- * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
- *         ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
- *
-*/
-#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
-#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }
-#define UNUSED_PINS
-
-/* Backlight Setup */
-#define BACKLIGHT_PIN F5
-#define BACKLIGHT_LEVELS 6
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCING_DELAY 5
-
-/* RGB Underglow
- * F6 PIN for XD60v3 that has pre-soldered LEDs
- */
-#define RGB_DI_PIN F6
-#define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 12
-#define RGBLIGHT_HUE_STEP 10
-#define RGBLIGHT_SAT_STEP 17
-#define RGBLIGHT_VAL_STEP 17
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
diff --git a/keyboards/xd60/rev3/rules.mk b/keyboards/xd60/rev3/rules.mk
deleted file mode 100644
index f33fff76ce..0000000000
--- a/keyboards/xd60/rev3/rules.mk
+++ /dev/null
@@ -1,67 +0,0 @@
-# MCU name
-# MCU = at90usb1287
-MCU = atmega32u4
-
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-# LUFA specific
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = no         # Commands for debug and configuration
-NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = no           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-
-LAYOUTS = 60_ansi