Clean up some user keymaps specifying MCU (#11966)

2 files changed, 9 insertions, 99 deletions

diff --git a/keyboards/planck/keymaps/handwired_binaryplease/config.h b/keyboards/planck/keymaps/handwired_binaryplease/config.h
index 8cd4fe40a9..abf9f5771f 100644
--- a/keyboards/planck/keymaps/handwired_binaryplease/config.h
+++ b/keyboards/planck/keymaps/handwired_binaryplease/config.h
@@ -1,37 +1,11 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "../../config.h"
-
-/* USB Device descriptor parameter */
-
-
-
-#undef VENDOR_ID
-#undef PRODUCT_ID
 #undef MANUFACTURER
+#define MANUFACTURER binaryplease
 #undef PRODUCT
-#undef MATRIX_ROW_PINS
-#undef MATRIX_COL_PINS
-#undef UNUSED_PINS
-#undef BACKLIGHT_PIN
-#undef BACKLIGHT_LEVELS
-
-
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6060
-#define MANUFACTURER    binaryplease
-#define PRODUCT         Teensy_Planck
+#define PRODUCT      Teensy_Planck
 
+#undef MATRIX_ROW_PINS
 #define MATRIX_ROW_PINS { D3, D2, D1, D0 }
+#undef MATRIX_COL_PINS
 #define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B6, B5, B4, D7, D6, D4 }
-#define UNUSED_PINS
-
-#define BACKLIGHT_PIN B7
-
-/* number of backlight levels */
-#define BACKLIGHT_LEVELS 0
-
-
-#endif
diff --git a/keyboards/planck/keymaps/handwired_binaryplease/rules.mk b/keyboards/planck/keymaps/handwired_binaryplease/rules.mk
index cf37fa6f3b..459c7bce6c 100644
--- a/keyboards/planck/keymaps/handwired_binaryplease/rules.mk
+++ b/keyboards/planck/keymaps/handwired_binaryplease/rules.mk
@@ -1,68 +1,4 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
-MIDI_ENABLE = yes            # MIDI controls
-AUDIO_ENABLE = no           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
-API_SYSEX_ENABLE = no
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
-
+CONSOLE_ENABLE = no
+NKRO_ENABLE = no
+MIDI_ENABLE = yes
+AUDIO_ENABLE = no