remove all keyboards but ergodox and planck

3 files changed, 0 insertions, 198 deletions

diff --git a/keyboards/jm60/boards/JM60_BOARD/board.c b/keyboards/jm60/boards/JM60_BOARD/board.c
deleted file mode 100644
index d953d6a135..0000000000
--- a/keyboards/jm60/boards/JM60_BOARD/board.c
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#include "hal.h"
-
-/**
- * @brief   PAL setup.
- * @details Digital I/O ports static configuration as defined in @p board.h.
- *          This variable is used by the HAL when initializing the PAL driver.
- */
-#if HAL_USE_PAL || defined(__DOXYGEN__)
-const PALConfig pal_default_config =
-{
-  {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
-  {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
-  {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
-  {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
-  {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
-};
-#endif
-
-/*
- * Early initialization code.
- * This initialization must be performed just after stack setup and before
- * any other initialization.
- */
-void __early_init(void) {
-
-  stm32_clock_init();
-}
-
-/*
- * Board-specific initialization code.
- */
-void boardInit(void) {
-	AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE;
-
-}
diff --git a/keyboards/jm60/boards/JM60_BOARD/board.h b/keyboards/jm60/boards/JM60_BOARD/board.h
deleted file mode 100644
index 74815122c3..0000000000
--- a/keyboards/jm60/boards/JM60_BOARD/board.h
+++ /dev/null
@@ -1,142 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-/*
- * Board identifier.
- */
-#define BOARD_JM60
-#define BOARD_NAME              "JM60 keyboard"
-
-/*
- * Board frequencies.
- */
-#define STM32_LSECLK            32768
-#define STM32_HSECLK            8000000
-
-/*
- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
- *
- * Only xB (128KB Flash) is defined, but it's identical to the
- * x8 version (64KB Flash) except for the Flash region size in the
- * linker script. For x8 parts use xB here and change to the x8 linker
- * script in the project Makefile.
- */
-#define STM32F103xB
-
-/*
- * IO pins assignments
- *
- * numbering is sorted by onboard/connectors, as from the schematics in
- * http://www.vcc-gnd.com/read.php?tid=369
- */
-
-/* on-board */
-#define GPIOA_USBDM             11      // pin 8
-#define GPIOA_USBDP             12      // pin 9
-
-#define GPIOC_OSC32_IN          14
-#define GPIOC_OSC32_OUT         15
-
-/*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- *
- * The digits have the following meaning:
- *   0 - Analog input.
- *   1 - Push Pull output 10MHz.
- *   2 - Push Pull output 2MHz.
- *   3 - Push Pull output 50MHz.
- *   4 - Digital input.
- *   5 - Open Drain output 10MHz.
- *   6 - Open Drain output 2MHz.
- *   7 - Open Drain output 50MHz.
- *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
- *   9 - Alternate Push Pull output 10MHz.
- *   A - Alternate Push Pull output 2MHz.
- *   B - Alternate Push Pull output 50MHz.
- *   C - Reserved.
- *   D - Alternate Open Drain output 10MHz.
- *   E - Alternate Open Drain output 2MHz.
- *   F - Alternate Open Drain output 50MHz.
- * Please refer to the STM32 Reference Manual for details.
- */
-
-/*
- * Port A setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOACRL            0x88888888      /*  PA7...PA0 */
-#define VAL_GPIOACRH            0x88888888      /* PA15...PA8 */
-#define VAL_GPIOAODR            0xFFFFFFFF
-
-/*
- * Port B setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOBCRL            0x88888888      /*  PB7...PB0 */
-#define VAL_GPIOBCRH            0x88888888      /* PB15...PB8 */
-#define VAL_GPIOBODR            0xFFFFFFFF
-
-/*
- * Port C setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */
-#define VAL_GPIOCCRH            0x88888888      /* PC15...PC8 */
-#define VAL_GPIOCODR            0xFFFFFFFF
-
-/*
- * Port D setup.
- * Everything input with pull-up except:
- * PD0  - Normal input (XTAL).
- * PD1  - Normal input (XTAL).
- */
-#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */
-#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */
-#define VAL_GPIODODR            0xFFFFFFFF
-
-/*
- * Port E setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */
-#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */
-#define VAL_GPIOEODR            0xFFFFFFFF
-
-/*
- * USB bus activation macro, required by the USB driver.
- */
-#define usb_lld_connect_bus(usbp)	/* always connected */
-
-/*
- * USB bus de-activation macro, required by the USB driver.
- */
-#define usb_lld_disconnect_bus(usbp)	/* always connected */
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
-  void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif /* _FROM_ASM_ */
-
-#endif /* _BOARD_H_ */
diff --git a/keyboards/jm60/boards/JM60_BOARD/board.mk b/keyboards/jm60/boards/JM60_BOARD/board.mk
deleted file mode 100644
index e2f051c314..0000000000
--- a/keyboards/jm60/boards/JM60_BOARD/board.mk
+++ /dev/null
@@ -1,5 +0,0 @@
-# List of all the board related files.
-BOARDSRC = $(BOARD_PATH)/boards/JM60_BOARD/board.c
-
-# Required include directories
-BOARDINC = $(BOARD_PATH)/boards/JM60_BOARD