Split keyboard makefiles into rules and Makefile

2 files changed, 71 insertions, 74 deletions

diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile
index 39a9cc0ae1..4e2a6f00fd 100644
--- a/keyboards/gh60/Makefile
+++ b/keyboards/gh60/Makefile
@@ -1,74 +1,3 @@
-

-

-# MCU name

-#MCU = at90usb1287

-MCU = atmega32u4

-

-# Processor frequency.

-#     This will define a symbol, F_CPU, in all source code files equal to the

-#     processor frequency in Hz. You can then use this symbol in your source code to

-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

-#     automatically to create a 32-bit value in your source code.

-#

-#     This will be an integer division of F_USB below, as it is sourced by

-#     F_USB after it has run through any CPU prescalers. Note that this value

-#     does not *change* the processor frequency - it should merely be updated to

-#     reflect the processor speed set externally so that the code can use accurate

-#     software delays.

-F_CPU = 16000000

-

-

-#

-# LUFA specific

-#

-# Target architecture (see library "Board Types" documentation).

-ARCH = AVR8

-

-# Input clock frequency.

-#     This will define a symbol, F_USB, in all source code files equal to the

-#     input clock frequency (before any prescaling is performed) in Hz. This value may

-#     differ from F_CPU if prescaling is used on the latter, and is required as the

-#     raw input clock is fed directly to the PLL sections of the AVR for high speed

-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'

-#     at the end, this will be done automatically to create a 32-bit value in your

-#     source code.

-#

-#     If no clock division is performed on the input clock inside the AVR (via the

-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.

-F_USB = $(F_CPU)

-

-# Interrupt driven control endpoint task(+60)

-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

-

-

-# Boot Section Size in *bytes*

-#   Teensy halfKay   512

-#   Teensy++ halfKay 1024

-#   Atmel DFU loader 4096

-#   LUFA bootloader  4096

-#   USBaspLoader     2048

-OPT_DEFS += -DBOOTLOADER_SIZE=4096

-

-

-# Build Options

-#   comment out to disable the options.

-#

-BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)

-MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)

-EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)

-# CONSOLE_ENABLE ?= yes		# Console for debug(+400)

-# COMMAND_ENABLE ?= yes		# Commands for debug and configuration

-KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key

-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE

-# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend

-NKRO_ENABLE ?= yes			# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work

-# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality

-# MIDI_ENABLE ?= YES			# MIDI controls

-# UNICODE_ENABLE ?= YES		# Unicode

-# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID

-

-

-ifndef QUANTUM_DIR

-	include ../../Makefile

-endif

-

+ifndef MAKEFILE_INCLUDED
+	include ../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/gh60/rules.mk b/keyboards/gh60/rules.mk
new file mode 100644
index 0000000000..73f4bd76e8
--- /dev/null
+++ b/keyboards/gh60/rules.mk
@@ -0,0 +1,68 @@
+

+

+# MCU name

+#MCU = at90usb1287

+MCU = atmega32u4

+

+# Processor frequency.

+#     This will define a symbol, F_CPU, in all source code files equal to the

+#     processor frequency in Hz. You can then use this symbol in your source code to

+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

+#     automatically to create a 32-bit value in your source code.

+#

+#     This will be an integer division of F_USB below, as it is sourced by

+#     F_USB after it has run through any CPU prescalers. Note that this value

+#     does not *change* the processor frequency - it should merely be updated to

+#     reflect the processor speed set externally so that the code can use accurate

+#     software delays.

+F_CPU = 16000000

+

+

+#

+# LUFA specific

+#

+# Target architecture (see library "Board Types" documentation).

+ARCH = AVR8

+

+# Input clock frequency.

+#     This will define a symbol, F_USB, in all source code files equal to the

+#     input clock frequency (before any prescaling is performed) in Hz. This value may

+#     differ from F_CPU if prescaling is used on the latter, and is required as the

+#     raw input clock is fed directly to the PLL sections of the AVR for high speed

+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'

+#     at the end, this will be done automatically to create a 32-bit value in your

+#     source code.

+#

+#     If no clock division is performed on the input clock inside the AVR (via the

+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.

+F_USB = $(F_CPU)

+

+# Interrupt driven control endpoint task(+60)

+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

+

+

+# Boot Section Size in *bytes*

+#   Teensy halfKay   512

+#   Teensy++ halfKay 1024

+#   Atmel DFU loader 4096

+#   LUFA bootloader  4096

+#   USBaspLoader     2048

+OPT_DEFS += -DBOOTLOADER_SIZE=4096

+

+

+# Build Options

+#   comment out to disable the options.

+#

+BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)

+MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)

+EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)

+# CONSOLE_ENABLE ?= yes		# Console for debug(+400)

+# COMMAND_ENABLE ?= yes		# Commands for debug and configuration

+KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key

+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE

+# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend

+NKRO_ENABLE ?= yes			# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work

+# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality

+# MIDI_ENABLE ?= YES			# MIDI controls

+# UNICODE_ENABLE ?= YES		# Unicode

+# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID