Revert "Convert ErgoDox EZ to Matrix Lite (qmk#10189)"

This reverts commit 396b86b92d8010ac929f30768cc98643ea019986.

1 files changed, 66 insertions, 18 deletions

diff --git a/keyboards/ergodox_ez/rules.mk b/keyboards/ergodox_ez/rules.mk
index b6311aca3e..728a7a4467 100644
--- a/keyboards/ergodox_ez/rules.mk
+++ b/keyboards/ergodox_ez/rules.mk
@@ -1,16 +1,64 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make = Make software.
+#
+# make clean = Clean out built project files.
+#
+# That's pretty much all you need. To compile, always go make clean,
+# followed by make.
+#
+# For advanced users only:
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+#----------------------------------------------------------------------------
+
 # MCU name
 MCU = atmega32u4
 
-# Bootloader selection
-#   Teensy       halfkay
-#   Pro Micro    caterina
-#   Atmel DFU    atmel-dfu
-#   LUFA DFU     lufa-dfu
-#   QMK DFU      qmk-dfu
-#   ATmega32A    bootloadHID
-#   ATmega328P   USBasp
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = halfkay
 
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
 # If you have Left LEDs (see
 # https://geekhack.org/index.php?topic=22780.msg873819#msg873819 for
 # details), include the following define:
@@ -19,19 +67,19 @@ BOOTLOADER = halfkay
 # Build Options
 #   comment out to disable the options.
 #
-BOOTMAGIC_ENABLE = no   # Virtual DIP switch configuration
-MOUSEKEY_ENABLE  = yes  # Mouse keys
-EXTRAKEY_ENABLE  = yes  # Audio control and System control
-CONSOLE_ENABLE   = no   # Console for debug
-COMMAND_ENABLE   = yes  # Commands for debug and configuration
-CUSTOM_MATRIX    = lite # Custom matrix file for the ErgoDox EZ
-NKRO_ENABLE      = yes  # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-UNICODE_ENABLE   = yes  # Unicode
-SWAP_HANDS_ENABLE= yes  # Allow swapping hands of keyboard
+BOOTMAGIC_ENABLE = no  # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE  = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE  = yes # Audio control and System control(+450)
+CONSOLE_ENABLE   = no  # Console for debug(+400)
+COMMAND_ENABLE   = yes # Commands for debug and configuration
+CUSTOM_MATRIX    = yes # Custom matrix file for the ErgoDox EZ
+NKRO_ENABLE      = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+UNICODE_ENABLE   = yes # Unicode
+SWAP_HANDS_ENABLE= yes # Allow swapping hands of keyboard
 SLEEP_LED_ENABLE = no
 API_SYSEX_ENABLE = no
 
-RGB_MATRIX_ENABLE = no  # enable later
+RGB_MATRIX_ENABLE = no # enable later
 DEBOUNCE_TYPE = eager_pr
 
 # project specific files