/* * ---------------------------------------------------------------------------- * "THE BEER-WARE LICENSE" (Revision 42): * <https://github.com/Legonut> wrote this file. As long as you retain this * notice you can do whatever you want with this stuff. If we meet some day, and * you think this stuff is worth it, you can buy me a beer in return. David Rauseo * ---------------------------------------------------------------------------- */ #pragma once #include "config_common.h" /* USB Device descriptor parameter */ #define VENDOR_ID 0x3535 #define PRODUCT_ID 0x3505 #define MANUFACTURER RGBKB #define PRODUCT Mün #define USB_POLLING_INTERVAL_MS 1 /* Matrix Configuration - Rows are doubled up */ #define MATRIX_ROWS 14 // B1, A2 reserved for encoder / touch encoder support #define MATRIX_ROW_PINS { A1, A3, B3, A13, B15, B1, A2 } #define MATRIX_COLS 7 #define MATRIX_COL_PINS { A0, B11, B0, B10, B12, B2, A8 } #define MATRIX_IO_DELAY 5 #define BUSY_WAIT #define BUSY_WAIT_INSTRUCTIONS 35 // Increase if two rows are pressed at the same time. #define GPIO_INPUT_PIN_DELAY 10 /* Touchbar adjustments */ #define TOUCH_DEADZONE 50 // width of a "button", wider inputs will be interpreted as a swipe #define TOUCH_TERM 350 // time of a "button" touch, longer inputs will be a swipe #define TOUCH_RESOLUTION 25 // sensitivity of swipes, lower=faster /* Encoder Configuration */ #define ENCODERS_PAD_A { B8, B9 } #define ENCODERS_PAD_B { A14, A15 } #define TOUCH_SEGMENTS 3 /* COL2ROW or ROW2COL */ #define DIODE_DIRECTION COL2ROW /* CRC Configuration */ #define CRC8_OPTIMIZE_SPEED #define CRC8_USE_TABLE /* Split Keyboard Configuration */ #define EE_HANDS #define SPLIT_USB_DETECT // also handles the SERIAL_USART_TX_PIN define #define SOFT_SERIAL_PIN A9 #define SERIAL_USART_TX_PAL_MODE 7 #define SERIAL_USART_TIMEOUT 5 #define SERIAL_USART_DRIVER SD1 //#define SERIAL_USART_FULL_DUPLEX - Waiting on reunification pr #if SERIAL_USART_FULL_DUPLEX #define SERIAL_USART_RX_PIN A10 #define SERIAL_USART_RX_PAL_MODE 7 // Mun connects TX to TX and RX to RX as we were planning on i2c split, so we need pin swap for full duplex #define SERIAL_USART_PIN_SWAP #define SERIAL_USART_SPEED (2 * 1024 * 1024) #else #define SERIAL_USART_SPEED (1 * 1024 * 1024) #endif /* Split Transport Features */ #define SPLIT_TRANSPORT_MIRROR #define SPLIT_LAYER_STATE_ENABLE #define SPLIT_LED_STATE_ENABLE #define SPLIT_TRANSACTION_IDS_KB TOUCH_ENCODER_SYNC, RGB_MENU_SYNC /* RGB LED Configuration */ #define RGB_DI_PIN B5 #define RGBLED_NUM 98 #define RGBLED_SPLIT { 49, 49 } #define RGBLIGHT_ANIMATIONS #define DRIVER_LED_TOTAL RGBLED_NUM #define RGB_MATRIX_SPLIT RGBLED_SPLIT #define RGB_MATRIX_CENTER { 128, 34 } #define RGB_MATRIX_LED_FLUSH_LIMIT 33 #define RGB_MATRIX_LED_PROCESS_LIMIT 10 #define RGB_MATRIX_KEYPRESSES #define RGB_MATRIX_FRAMEBUFFER_EFFECTS #define RGB_DISABLE_WHEN_USB_SUSPENDED #if RGB_UNLIMITED_POWER #define RGBLIGHT_LIMIT_VAL 255 #else #define RGBLIGHT_LIMIT_VAL 127 #endif #define RGB_MATRIX_MAXIMUM_BRIGHTNESS RGBLIGHT_LIMIT_VAL #define WS2812_PWM_DRIVER PWMD3 #define WS2812_PWM_CHANNEL 2 #define WS2812_PWM_PAL_MODE 2 #define WS2812_DMA_STREAM STM32_DMA1_STREAM3 #define WS2812_DMA_CHANNEL 3 #define TOUCH_UPDATE_INTERVAL 33 #define OLED_UPDATE_INTERVAL 33 #define TAP_CODE_DELAY 5