From b7696fb3b0a38bd795cbda6d7629711c3564620c Mon Sep 17 00:00:00 2001 From: dbroqua Date: Tue, 20 Dec 2016 18:43:06 +0100 Subject: - Updated gh60 files --- keyboards/gh60/gh60.h | 2 +- keyboards/gh60/keymaps/dbroqua_hhkb/Makefile | 112 ++++++++++++++++++++++++ keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c | 124 +++++++++++++++++++++++++++ 3 files changed, 237 insertions(+), 1 deletion(-) create mode 100644 keyboards/gh60/keymaps/dbroqua_hhkb/Makefile create mode 100644 keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/gh60.h b/keyboards/gh60/gh60.h index 66bc2790d2..99ccf17574 100644 --- a/keyboards/gh60/gh60.h +++ b/keyboards/gh60/gh60.h @@ -72,4 +72,4 @@ inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); } { K40, K41, K42, KC_NO, KC_NO, K45, KC_NO, KC_NO, KC_NO, K49, K4A, K4B, K4C, K4D } \ } -#endif +#endif \ No newline at end of file diff --git a/keyboards/gh60/keymaps/dbroqua_hhkb/Makefile b/keyboards/gh60/keymaps/dbroqua_hhkb/Makefile new file mode 100644 index 0000000000..b9bbb669d7 --- /dev/null +++ b/keyboards/gh60/keymaps/dbroqua_hhkb/Makefile @@ -0,0 +1,112 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID +# RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif + diff --git a/keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c b/keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c new file mode 100644 index 0000000000..0c2e980d2f --- /dev/null +++ b/keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c @@ -0,0 +1,124 @@ +#include "gh60.h" +#include "action_layer.h" + +#define _DEFAULT 0 +#define _FN 1 +#define _WASD 2 + +//bool esc_led_on; + +enum planck_keycodes { + DEFAULT = SAFE_RANGE +}; + +// Fillers to make layering more clear +#define ______ KC_TRNS + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +/* Qwerty gui/alt/space/alt/gui + * ,-----------------------------------------------------------------------------------------. + * | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` | + * |-----------------------------------------------------------------------------------------+ + * | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Bksp | + * |-----------------------------------------------------------------------------------------+ + * | Ctrl | A | S | D | F | G | H | J | K | L | ; | ' | Enter | + * |-----------------------------------------------------------------------------------------+ + * | Shift | Z | X | C | V | B | N | M | , | . | / | RShift | FN | + * |-----------------------------------------------------------------------------------------+ + * |LGUI | LAlt | Space | RAlt |RGUI | + * `-----------------------------------------------------------------' + */ + [_DEFAULT] = KEYMAP_HHKB( /* Basic QWERTY */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \ + KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(_FN), \ + ______, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, ______, ______ \ + ), + +/* FN Layer + * ,-----------------------------------------------------------------------------------------. + * | | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | Ins | Del | + * |-----------------------------------------------------------------------------------------+ + * | CAPS | | | | | | | | Psc | Slck| Paus| Up | | | + * |-----------------------------------------------------------------------------------------+ + * | | Vol-| Vol+| Mute| | | * | / | Home| PgUp| Left|Right| | + * |-----------------------------------------------------------------------------------------+ + * | | Prev| Play| Next| | | + | - | End |PgDn| Down| | | + * |-----------------------------------------------------------------------------------------+ + * | | | | Stop | | + * `-----------------------------------------------------------------' + */ + [_FN] = KEYMAP_HHKB( /* Layer 1 */ + ______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \ + KC_CAPS, ______, ______, ______, ______, ______, ______, ______, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, ______, ______, \ + ______, KC_VOLD, KC_VOLU, KC_MUTE, ______, ______, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT,______, \ + ______, KC_MPRV, KC_MPLY, KC_MNXT, ______, ______, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, ______, ______, \ + ______, ______, ______, KC_FN1, KC_MSTP, ______, ______, ______ \ + ), + +/* FN Layer + * ,-----------------------------------------------------------------------------------------. + * | | | | | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | Up | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | Left| Down|Right| | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | + * `-----------------------------------------------------------------' + */ + [_WASD] = KEYMAP_HHKB( /* Layer 1 */ + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, ______, KC_UP, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, KC_LEFT, KC_DOWN, KC_RGHT, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______,______, \ + ______, ______, ______, ______, ______, ______, ______, ______ \ + ) +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + return MACRO_NONE; +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay + [1] = ACTION_LAYER_TOGGLE(2), // toggle wasd overlay +}; + +//bool process_record_user(uint16_t keycode, keyrecord_t *record) { +// switch (keycode) { +// case ESC_LED: +// if (record->event.pressed) { +// if (esc_led_on == true ){ +// gh60_esc_led_off(); +// }else{ +// gh60_esc_led_on(); +// } +// esc_led_on = !esc_led_on; +// } +// return false; +// break; +// } +// return true; +//} + +void matrix_scan_user(void) { + uint32_t layer = layer_state; + + if (layer & (1<<1)) { + gh60_fn_led_on(); + } else { + gh60_fn_led_off(); + } + + if (layer & (1<<2)) { + gh60_wasd_leds_on(); + } else { + gh60_wasd_leds_off(); + } +}; \ No newline at end of file -- cgit v1.2.3 From 5ee136a36f6fd8cb697f97baf0d72192615b857d Mon Sep 17 00:00:00 2001 From: dbroqua Date: Wed, 21 Dec 2016 23:12:33 +0100 Subject: - Renamed dbroqua_hhkb as dbroqua for gh60 layout --- keyboards/gh60/keymaps/dbroqua/Makefile | 112 ++++++++++++++++++++++++ keyboards/gh60/keymaps/dbroqua/keymap.c | 124 +++++++++++++++++++++++++++ keyboards/gh60/keymaps/dbroqua_hhkb/Makefile | 112 ------------------------ keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c | 124 --------------------------- 4 files changed, 236 insertions(+), 236 deletions(-) create mode 100644 keyboards/gh60/keymaps/dbroqua/Makefile create mode 100644 keyboards/gh60/keymaps/dbroqua/keymap.c delete mode 100644 keyboards/gh60/keymaps/dbroqua_hhkb/Makefile delete mode 100644 keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/keymaps/dbroqua/Makefile b/keyboards/gh60/keymaps/dbroqua/Makefile new file mode 100644 index 0000000000..b9bbb669d7 --- /dev/null +++ b/keyboards/gh60/keymaps/dbroqua/Makefile @@ -0,0 +1,112 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID +# RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif + diff --git a/keyboards/gh60/keymaps/dbroqua/keymap.c b/keyboards/gh60/keymaps/dbroqua/keymap.c new file mode 100644 index 0000000000..0c2e980d2f --- /dev/null +++ b/keyboards/gh60/keymaps/dbroqua/keymap.c @@ -0,0 +1,124 @@ +#include "gh60.h" +#include "action_layer.h" + +#define _DEFAULT 0 +#define _FN 1 +#define _WASD 2 + +//bool esc_led_on; + +enum planck_keycodes { + DEFAULT = SAFE_RANGE +}; + +// Fillers to make layering more clear +#define ______ KC_TRNS + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +/* Qwerty gui/alt/space/alt/gui + * ,-----------------------------------------------------------------------------------------. + * | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` | + * |-----------------------------------------------------------------------------------------+ + * | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Bksp | + * |-----------------------------------------------------------------------------------------+ + * | Ctrl | A | S | D | F | G | H | J | K | L | ; | ' | Enter | + * |-----------------------------------------------------------------------------------------+ + * | Shift | Z | X | C | V | B | N | M | , | . | / | RShift | FN | + * |-----------------------------------------------------------------------------------------+ + * |LGUI | LAlt | Space | RAlt |RGUI | + * `-----------------------------------------------------------------' + */ + [_DEFAULT] = KEYMAP_HHKB( /* Basic QWERTY */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \ + KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(_FN), \ + ______, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, ______, ______ \ + ), + +/* FN Layer + * ,-----------------------------------------------------------------------------------------. + * | | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | Ins | Del | + * |-----------------------------------------------------------------------------------------+ + * | CAPS | | | | | | | | Psc | Slck| Paus| Up | | | + * |-----------------------------------------------------------------------------------------+ + * | | Vol-| Vol+| Mute| | | * | / | Home| PgUp| Left|Right| | + * |-----------------------------------------------------------------------------------------+ + * | | Prev| Play| Next| | | + | - | End |PgDn| Down| | | + * |-----------------------------------------------------------------------------------------+ + * | | | | Stop | | + * `-----------------------------------------------------------------' + */ + [_FN] = KEYMAP_HHKB( /* Layer 1 */ + ______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \ + KC_CAPS, ______, ______, ______, ______, ______, ______, ______, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, ______, ______, \ + ______, KC_VOLD, KC_VOLU, KC_MUTE, ______, ______, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT,______, \ + ______, KC_MPRV, KC_MPLY, KC_MNXT, ______, ______, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, ______, ______, \ + ______, ______, ______, KC_FN1, KC_MSTP, ______, ______, ______ \ + ), + +/* FN Layer + * ,-----------------------------------------------------------------------------------------. + * | | | | | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | Up | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | Left| Down|Right| | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | + * `-----------------------------------------------------------------' + */ + [_WASD] = KEYMAP_HHKB( /* Layer 1 */ + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, ______, KC_UP, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, KC_LEFT, KC_DOWN, KC_RGHT, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______,______, \ + ______, ______, ______, ______, ______, ______, ______, ______ \ + ) +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + return MACRO_NONE; +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay + [1] = ACTION_LAYER_TOGGLE(2), // toggle wasd overlay +}; + +//bool process_record_user(uint16_t keycode, keyrecord_t *record) { +// switch (keycode) { +// case ESC_LED: +// if (record->event.pressed) { +// if (esc_led_on == true ){ +// gh60_esc_led_off(); +// }else{ +// gh60_esc_led_on(); +// } +// esc_led_on = !esc_led_on; +// } +// return false; +// break; +// } +// return true; +//} + +void matrix_scan_user(void) { + uint32_t layer = layer_state; + + if (layer & (1<<1)) { + gh60_fn_led_on(); + } else { + gh60_fn_led_off(); + } + + if (layer & (1<<2)) { + gh60_wasd_leds_on(); + } else { + gh60_wasd_leds_off(); + } +}; \ No newline at end of file diff --git a/keyboards/gh60/keymaps/dbroqua_hhkb/Makefile b/keyboards/gh60/keymaps/dbroqua_hhkb/Makefile deleted file mode 100644 index b9bbb669d7..0000000000 --- a/keyboards/gh60/keymaps/dbroqua_hhkb/Makefile +++ /dev/null @@ -1,112 +0,0 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -# CONSOLE_ENABLE ?= yes # Console for debug(+400) -# COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID -# RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow - -ifndef QUANTUM_DIR - include ../../../../Makefile -endif - diff --git a/keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c b/keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c deleted file mode 100644 index 0c2e980d2f..0000000000 --- a/keyboards/gh60/keymaps/dbroqua_hhkb/keymap.c +++ /dev/null @@ -1,124 +0,0 @@ -#include "gh60.h" -#include "action_layer.h" - -#define _DEFAULT 0 -#define _FN 1 -#define _WASD 2 - -//bool esc_led_on; - -enum planck_keycodes { - DEFAULT = SAFE_RANGE -}; - -// Fillers to make layering more clear -#define ______ KC_TRNS - -const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { -/* Qwerty gui/alt/space/alt/gui - * ,-----------------------------------------------------------------------------------------. - * | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` | - * |-----------------------------------------------------------------------------------------+ - * | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Bksp | - * |-----------------------------------------------------------------------------------------+ - * | Ctrl | A | S | D | F | G | H | J | K | L | ; | ' | Enter | - * |-----------------------------------------------------------------------------------------+ - * | Shift | Z | X | C | V | B | N | M | , | . | / | RShift | FN | - * |-----------------------------------------------------------------------------------------+ - * |LGUI | LAlt | Space | RAlt |RGUI | - * `-----------------------------------------------------------------' - */ - [_DEFAULT] = KEYMAP_HHKB( /* Basic QWERTY */ - KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \ - KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \ - KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \ - KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(_FN), \ - ______, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, ______, ______ \ - ), - -/* FN Layer - * ,-----------------------------------------------------------------------------------------. - * | | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | Ins | Del | - * |-----------------------------------------------------------------------------------------+ - * | CAPS | | | | | | | | Psc | Slck| Paus| Up | | | - * |-----------------------------------------------------------------------------------------+ - * | | Vol-| Vol+| Mute| | | * | / | Home| PgUp| Left|Right| | - * |-----------------------------------------------------------------------------------------+ - * | | Prev| Play| Next| | | + | - | End |PgDn| Down| | | - * |-----------------------------------------------------------------------------------------+ - * | | | | Stop | | - * `-----------------------------------------------------------------' - */ - [_FN] = KEYMAP_HHKB( /* Layer 1 */ - ______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \ - KC_CAPS, ______, ______, ______, ______, ______, ______, ______, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, ______, ______, \ - ______, KC_VOLD, KC_VOLU, KC_MUTE, ______, ______, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT,______, \ - ______, KC_MPRV, KC_MPLY, KC_MNXT, ______, ______, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, ______, ______, \ - ______, ______, ______, KC_FN1, KC_MSTP, ______, ______, ______ \ - ), - -/* FN Layer - * ,-----------------------------------------------------------------------------------------. - * | | | | | | | | | | | | | | | | - * |-----------------------------------------------------------------------------------------+ - * | | | Up | | | | | | | | | | | | - * |-----------------------------------------------------------------------------------------+ - * | | Left| Down|Right| | | | | | | | | | - * |-----------------------------------------------------------------------------------------+ - * | | | | | | | | | | | | | | - * |-----------------------------------------------------------------------------------------+ - * | | | | | | - * `-----------------------------------------------------------------' - */ - [_WASD] = KEYMAP_HHKB( /* Layer 1 */ - ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ - ______, ______, KC_UP, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ - ______, KC_LEFT, KC_DOWN, KC_RGHT, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ - ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______,______, \ - ______, ______, ______, ______, ______, ______, ______, ______ \ - ) -}; - -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - // MACRODOWN only works in this function - return MACRO_NONE; -}; - -const uint16_t PROGMEM fn_actions[] = { - [0] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay - [1] = ACTION_LAYER_TOGGLE(2), // toggle wasd overlay -}; - -//bool process_record_user(uint16_t keycode, keyrecord_t *record) { -// switch (keycode) { -// case ESC_LED: -// if (record->event.pressed) { -// if (esc_led_on == true ){ -// gh60_esc_led_off(); -// }else{ -// gh60_esc_led_on(); -// } -// esc_led_on = !esc_led_on; -// } -// return false; -// break; -// } -// return true; -//} - -void matrix_scan_user(void) { - uint32_t layer = layer_state; - - if (layer & (1<<1)) { - gh60_fn_led_on(); - } else { - gh60_fn_led_off(); - } - - if (layer & (1<<2)) { - gh60_wasd_leds_on(); - } else { - gh60_wasd_leds_off(); - } -}; \ No newline at end of file -- cgit v1.2.3 From 46ff5f3b9007e9fd4714ed7e34c7a8b77cf052ae Mon Sep 17 00:00:00 2001 From: dbroqua Date: Thu, 22 Dec 2016 08:26:55 +0100 Subject: - Fixed bad typo in dbroqua layout for gh60 - Removed unused function in dbroqua layout for gh60 --- keyboards/gh60/keymaps/dbroqua/keymap.c | 21 ++------------------- 1 file changed, 2 insertions(+), 19 deletions(-) (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/keymaps/dbroqua/keymap.c b/keyboards/gh60/keymaps/dbroqua/keymap.c index 0c2e980d2f..3c16baa226 100644 --- a/keyboards/gh60/keymaps/dbroqua/keymap.c +++ b/keyboards/gh60/keymaps/dbroqua/keymap.c @@ -57,7 +57,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { ______, ______, ______, KC_FN1, KC_MSTP, ______, ______, ______ \ ), -/* FN Layer +/* WASD Layer * ,-----------------------------------------------------------------------------------------. * | | | | | | | | | | | | | | | | * |-----------------------------------------------------------------------------------------+ @@ -70,7 +70,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * | | | | | | * `-----------------------------------------------------------------' */ - [_WASD] = KEYMAP_HHKB( /* Layer 1 */ + [_WASD] = KEYMAP_HHKB( /* Layer 2 */ ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ ______, ______, KC_UP, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ ______, KC_LEFT, KC_DOWN, KC_RGHT, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ @@ -90,23 +90,6 @@ const uint16_t PROGMEM fn_actions[] = { [1] = ACTION_LAYER_TOGGLE(2), // toggle wasd overlay }; -//bool process_record_user(uint16_t keycode, keyrecord_t *record) { -// switch (keycode) { -// case ESC_LED: -// if (record->event.pressed) { -// if (esc_led_on == true ){ -// gh60_esc_led_off(); -// }else{ -// gh60_esc_led_on(); -// } -// esc_led_on = !esc_led_on; -// } -// return false; -// break; -// } -// return true; -//} - void matrix_scan_user(void) { uint32_t layer = layer_state; -- cgit v1.2.3 From 033f0b92c4c5f6fbad08bacc87f2cf6776949f90 Mon Sep 17 00:00:00 2001 From: dbroqua Date: Sat, 24 Dec 2016 14:43:07 +0100 Subject: - Added RGB layer on dbroqua GH60 layout --- keyboards/gh60/keymaps/dbroqua/Makefile | 2 +- keyboards/gh60/keymaps/dbroqua/config.h | 187 ++++++++++++++++++++++++++++++++ keyboards/gh60/keymaps/dbroqua/keymap.c | 109 +++++++++++++++++-- 3 files changed, 288 insertions(+), 10 deletions(-) create mode 100644 keyboards/gh60/keymaps/dbroqua/config.h (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/keymaps/dbroqua/Makefile b/keyboards/gh60/keymaps/dbroqua/Makefile index b9bbb669d7..f1644a8e49 100644 --- a/keyboards/gh60/keymaps/dbroqua/Makefile +++ b/keyboards/gh60/keymaps/dbroqua/Makefile @@ -104,7 +104,7 @@ NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: ht # MIDI_ENABLE ?= YES # MIDI controls # UNICODE_ENABLE ?= YES # Unicode # BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID -# RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow +RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow ifndef QUANTUM_DIR include ../../../../Makefile diff --git a/keyboards/gh60/keymaps/dbroqua/config.h b/keyboards/gh60/keymaps/dbroqua/config.h new file mode 100644 index 0000000000..75ccec0973 --- /dev/null +++ b/keyboards/gh60/keymaps/dbroqua/config.h @@ -0,0 +1,187 @@ +/* +Copyright 2012 Jun Wako + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT GH60 +#define DESCRIPTION t.m.k. keyboard firmware for GH60 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * RGB Underglow + * These settings are for the F4 by default: + * + * + * #define ws2812_PORTREG PORTF + * #define ws2812_DDRREG DDRF + * #define ws2812_pin PF4 + * #define RGBLED_NUM 14 // Number of LEDs + * #define RGBLIGHT_HUE_STEP 10 + * #define RGBLIGHT_SAT_STEP 17 + * #define RGBLIGHT_VAL_STEP 17 + * + * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. + * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. + * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c +*/ + +/* Deprecated code below +#define ws2812_PORTREG PORTF +#define ws2812_DDRREG DDRF +#define ws2812_pin PF4 +*/ +#define RGB_DI_PIN F4 +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 11 // Number of LEDs +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#endif diff --git a/keyboards/gh60/keymaps/dbroqua/keymap.c b/keyboards/gh60/keymaps/dbroqua/keymap.c index 3c16baa226..be88edc090 100644 --- a/keyboards/gh60/keymaps/dbroqua/keymap.c +++ b/keyboards/gh60/keymaps/dbroqua/keymap.c @@ -1,9 +1,11 @@ #include "gh60.h" #include "action_layer.h" +#include "rgblight.h" #define _DEFAULT 0 #define _FN 1 #define _WASD 2 +#define _SFX 3 //bool esc_led_on; @@ -50,11 +52,11 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * `-----------------------------------------------------------------' */ [_FN] = KEYMAP_HHKB( /* Layer 1 */ - ______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \ + TG(_SFX),KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \ KC_CAPS, ______, ______, ______, ______, ______, ______, ______, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, ______, ______, \ ______, KC_VOLD, KC_VOLU, KC_MUTE, ______, ______, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT,______, \ ______, KC_MPRV, KC_MPLY, KC_MNXT, ______, ______, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, ______, ______, \ - ______, ______, ______, KC_FN1, KC_MSTP, ______, ______, ______ \ + ______, ______, ______, TG(_WASD), KC_MSTP, ______, ______, ______ \ ), /* WASD Layer @@ -71,11 +73,32 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * `-----------------------------------------------------------------' */ [_WASD] = KEYMAP_HHKB( /* Layer 2 */ - ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ - ______, ______, KC_UP, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ - ______, KC_LEFT, KC_DOWN, KC_RGHT, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ - ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______,______, \ - ______, ______, ______, ______, ______, ______, ______, ______ \ + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, ______, KC_UP, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, KC_LEFT, KC_DOWN,KC_RGHT,______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______,______, \ + ______, ______, ______, ______, ______, ______, ______, ______ \ + ), + +/* SFX Layer + * ,-----------------------------------------------------------------------------------------. + * | | | | | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | BL- | BL+ | BL | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | RGBT| RGBM| | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | Hue+| Hue-| Sat+| Sat-| Val+| Val-| | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | + * `-----------------------------------------------------------------' + */ + [_SFX] = KEYMAP_HHKB( + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, F(0), F(1), ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \ + ______, F(2), F(3), F(4), F(5), F(6), F(7), ______, ______, ______, ______, ______, ______, \ + ______, ______, ______, ______, ______, ______, ______, ______ \ ) }; @@ -85,11 +108,73 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) return MACRO_NONE; }; +enum function_id { + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL +}; + const uint16_t PROGMEM fn_actions[] = { - [0] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay - [1] = ACTION_LAYER_TOGGLE(2), // toggle wasd overlay + [0] = ACTION_FUNCTION(RGBLED_TOGGLE), + [1] = ACTION_FUNCTION(RGBLED_STEP_MODE), + [2] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [3] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [4] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [5] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [6] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [7] = ACTION_FUNCTION(RGBLED_DECREASE_VAL) }; +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + switch (id) { + case RGBLED_TOGGLE: + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + } +} + void matrix_scan_user(void) { uint32_t layer = layer_state; @@ -104,4 +189,10 @@ void matrix_scan_user(void) { } else { gh60_wasd_leds_off(); } + + if (layer & (1<<3)) { + gh60_esc_led_on(); + } else { + gh60_esc_led_off(); + } }; \ No newline at end of file -- cgit v1.2.3