From e8b65d01709c2ebdf50c0aa95963d200fa4fa4c6 Mon Sep 17 00:00:00 2001 From: fauxpark Date: Sun, 6 Oct 2019 05:09:35 +1100 Subject: Cleanup rules.mk for 32U4 keyboards, A-F (#6804) * Cleanup rules.mk for 32U4 keyboards, A-F * Put back stuff in VIA keymaps --- keyboards/ergodox_ez/rules.mk | 72 ++++++++----------------------------------- 1 file changed, 12 insertions(+), 60 deletions(-) (limited to 'keyboards/ergodox_ez') diff --git a/keyboards/ergodox_ez/rules.mk b/keyboards/ergodox_ez/rules.mk index 2882072a62..dbc35f6836 100644 --- a/keyboards/ergodox_ez/rules.mk +++ b/keyboards/ergodox_ez/rules.mk @@ -1,68 +1,16 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC += matrix.c -QUANTUM_LIB_SRC += i2c_master.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # If you have Left LEDs (see # https://geekhack.org/index.php?topic=22780.msg873819#msg873819 for # details), include the following define: @@ -86,4 +34,8 @@ RGBLIGHT_ENABLE = yes RGB_MATRIX_ENABLE = no # enable later DEBOUNCE_TYPE = eager_pr +# project specific files +SRC += matrix.c +QUANTUM_LIB_SRC += i2c_master.c + LAYOUTS = ergodox -- cgit v1.2.3