From ded395e45d815cef58b454345bc536fa188d6280 Mon Sep 17 00:00:00 2001
From: Florian Didron <0x6664@hey.com>
Date: Tue, 13 Oct 2020 21:17:37 +0900
Subject: Revert "Revert "Convert ErgoDox EZ to Matrix Lite (qmk#10189)""

This reverts commit edd58256f58b44b00f8ae811941c63862693e4c4.
---
 keyboards/ergodox_ez/rules.mk | 84 ++++++++++---------------------------------
 1 file changed, 18 insertions(+), 66 deletions(-)

(limited to 'keyboards/ergodox_ez/rules.mk')

diff --git a/keyboards/ergodox_ez/rules.mk b/keyboards/ergodox_ez/rules.mk
index 728a7a4467..b6311aca3e 100644
--- a/keyboards/ergodox_ez/rules.mk
+++ b/keyboards/ergodox_ez/rules.mk
@@ -1,64 +1,16 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean,
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # If you have Left LEDs (see
 # https://geekhack.org/index.php?topic=22780.msg873819#msg873819 for
 # details), include the following define:
@@ -67,19 +19,19 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 # Build Options
 #   comment out to disable the options.
 #
-BOOTMAGIC_ENABLE = no  # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE  = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE  = yes # Audio control and System control(+450)
-CONSOLE_ENABLE   = no  # Console for debug(+400)
-COMMAND_ENABLE   = yes # Commands for debug and configuration
-CUSTOM_MATRIX    = yes # Custom matrix file for the ErgoDox EZ
-NKRO_ENABLE      = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-UNICODE_ENABLE   = yes # Unicode
-SWAP_HANDS_ENABLE= yes # Allow swapping hands of keyboard
+BOOTMAGIC_ENABLE = no   # Virtual DIP switch configuration
+MOUSEKEY_ENABLE  = yes  # Mouse keys
+EXTRAKEY_ENABLE  = yes  # Audio control and System control
+CONSOLE_ENABLE   = no   # Console for debug
+COMMAND_ENABLE   = yes  # Commands for debug and configuration
+CUSTOM_MATRIX    = lite # Custom matrix file for the ErgoDox EZ
+NKRO_ENABLE      = yes  # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+UNICODE_ENABLE   = yes  # Unicode
+SWAP_HANDS_ENABLE= yes  # Allow swapping hands of keyboard
 SLEEP_LED_ENABLE = no
 API_SYSEX_ENABLE = no
 
-RGB_MATRIX_ENABLE = no # enable later
+RGB_MATRIX_ENABLE = no  # enable later
 DEBOUNCE_TYPE = eager_pr
 
 # project specific files
-- 
cgit v1.2.3