From 59c783df488cc8bcd9b8c92e9b27692c1e1761ed Mon Sep 17 00:00:00 2001 From: Hung DO Date: Sun, 5 Jan 2020 08:04:49 +0700 Subject: [Keyboard] Add support for db63 hotswap rbg (#7771) * correct the matrix pin for db63 * first correct layout * adding RGB support for db63 * adding backlighting keycode * enable back extension * update readme for the bootloader * correct the capslock pin * update correct info.json and layout following suggestion * editing contact * Update keyboards/db/db63/README.md Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com> * Update keyboards/db/db63/README.md Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com> Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com> --- keyboards/db/db63/README.md | 21 ++ keyboards/db/db63/config.h | 42 ++++ keyboards/db/db63/db63.c | 17 ++ keyboards/db/db63/db63.h | 49 ++++ keyboards/db/db63/info.json | 18 ++ keyboards/db/db63/keymaps/default/keymap.c | 60 +++++ keyboards/db/db63/rules.mk | 24 ++ keyboards/db/db63/usbconfig.h | 383 +++++++++++++++++++++++++++++ 8 files changed, 614 insertions(+) create mode 100644 keyboards/db/db63/README.md create mode 100644 keyboards/db/db63/config.h create mode 100644 keyboards/db/db63/db63.c create mode 100644 keyboards/db/db63/db63.h create mode 100644 keyboards/db/db63/info.json create mode 100644 keyboards/db/db63/keymaps/default/keymap.c create mode 100644 keyboards/db/db63/rules.mk create mode 100644 keyboards/db/db63/usbconfig.h (limited to 'keyboards/db') diff --git a/keyboards/db/db63/README.md b/keyboards/db/db63/README.md new file mode 100644 index 0000000000..e886bed0a1 --- /dev/null +++ b/keyboards/db/db63/README.md @@ -0,0 +1,21 @@ +# DB63 + +A 65% keyboard hotswap with RGB that runs ps2avrgb natively, with USB C, RGB underglow and backlight. + +* Keyboard Maintainer: QMK Community +* Hardware Supported: DB63 (ATmega32A) +* [Keyboard layout](http://www.keyboard-layout-editor.com/#/gists/dadea703fc8bfc87dc7c480de9f3ef38) + +Make example for this keyboard (after setting up your build environment): + + make db/db63:default + +Flashing example for this keyboard ([after setting up the bootloadHID flashing environment](https://docs.qmk.fm/#/flashing_bootloadhid)) + + make db/db63:default:flash + +**Reset Key**: Hold down the key located at *K00*, commonly programmed as *Escape* while plugging in the keyboard. (*All backlight LEDs will flash which indicate the board is in bootloader mode.*) + +**Tips**: Another trick to enable the board in reset mode is using BootMapper Client->Options->Set Bootloader. (*This is only available for the first time, before flashing QMK Firmware.*) + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/db/db63/config.h b/keyboards/db/db63/config.h new file mode 100644 index 0000000000..468e0f8a97 --- /dev/null +++ b/keyboards/db/db63/config.h @@ -0,0 +1,42 @@ +/* +Copyright 2020 Hung DO + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#pragma once + +#define VENDOR_ID 0xFAAD +#define PRODUCT_ID 0x422D +#define DEVICE_VER 0x0200 +// You can edit those at usbconfig.h about line 250. These values will +// unforunatly be ignored so far +#define MANUFACTURER HNB +#define PRODUCT DB63v1 Hotswap + +#define MATRIX_ROWS 6 +#define MATRIX_COLS 14 + +#define MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5 } +#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 } +#define UNUSED_PINS + +#define RGBLED_NUM 18 +#define RGBLIGHT_ANIMATIONS + +#define NO_UART 1 + +#define BACKLIGHT_PIN D4 +#define BACKLIGHT_LEVELS 3 + diff --git a/keyboards/db/db63/db63.c b/keyboards/db/db63/db63.c new file mode 100644 index 0000000000..62ebb2cc69 --- /dev/null +++ b/keyboards/db/db63/db63.c @@ -0,0 +1,17 @@ +/* Copyright 2019 MechMerlin + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ + +#include "db63.h" diff --git a/keyboards/db/db63/db63.h b/keyboards/db/db63/db63.h new file mode 100644 index 0000000000..d9a4d1e6d2 --- /dev/null +++ b/keyboards/db/db63/db63.h @@ -0,0 +1,49 @@ +/* +Copyright 2020 Hung DO + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#pragma once + +#include "quantum.h" +#define _x_ KC_NO + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + * MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5 } + * MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 } + * + */ + +#define LAYOUT( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, \ + k10 , k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \ + k20 , k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \ + k30 , k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, \ + k40 , k41 , k42 , k43 , k44, k45, k46, k47 , k48 \ +) { \ + { k00, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_ }, \ + { _x_, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k46 }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3c, k3a, k47, _x_ }, \ + { k40, k41, k42, k43, k45, _x_, _x_, k44, _x_, _x_, _x_, k3b, _x_, k48 } \ +} + diff --git a/keyboards/db/db63/info.json b/keyboards/db/db63/info.json new file mode 100644 index 0000000000..b8ec10539e --- /dev/null +++ b/keyboards/db/db63/info.json @@ -0,0 +1,18 @@ +{ + "keyboard_name": "db63", + "url": "http://www.keyboard-layout-editor.com/#/gists/dadea703fc8bfc87dc7c480de9f3ef38", + "maintainer": "QMK Community", + "width": 15, + "height": 5, + "layouts": { + "LAYOUT": { + "layout": [ + { "label": "~", "x": 0, "y": 0 }, { "label": "!", "x": 1, "y": 0 }, { "label": "@", "x": 2, "y": 0 }, { "label": "#", "x": 3, "y": 0 }, { "label": "$", "x": 4, "y": 0 }, { "label": "%", "x": 5, "y": 0 }, { "label": "^", "x": 6, "y": 0 }, { "label": "&", "x": 7, "y": 0 }, { "label": "*", "x": 8, "y": 0 }, { "label": "(", "x": 9, "y": 0 }, { "label": ")", "x": 10, "y": 0 }, { "label": "_", "x": 11, "y": 0 }, { "label": "+", "x": 12, "y": 0 }, { "label": "Backspace", "x": 13, "y": 0, "w": 2 }, + { "label": "Tab", "x": 0, "y": 1, "w": 1.5 }, { "label": "Q", "x": 1.5, "y": 1 }, { "label": "W", "x": 2.5, "y": 1 }, { "label": "E", "x": 3.5, "y": 1 }, { "label": "R", "x": 4.5, "y": 1 }, { "label": "T", "x": 5.5, "y": 1 }, { "label": "Y", "x": 6.5, "y": 1 }, { "label": "U", "x": 7.5, "y": 1 }, { "label": "I", "x": 8.5, "y": 1 }, { "label": "O", "x": 9.5, "y": 1 }, { "label": "P", "x": 10.5, "y": 1 }, { "label": "{", "x": 11.5, "y": 1 }, { "label": "}", "x": 12.5, "y": 1 }, { "label": "|", "x": 13.5, "y": 1, "w": 1.5 }, + { "label": "Fn3", "x": 0, "y": 2, "w": 1.75 }, { "label": "A", "x": 1.75, "y": 2 }, { "label": "S", "x": 2.75, "y": 2 }, { "label": "D", "x": 3.75, "y": 2 }, { "label": "F", "x": 4.75, "y": 2 }, { "label": "G", "x": 5.75, "y": 2 }, { "label": "H", "x": 6.75, "y": 2 }, { "label": "J", "x": 7.75, "y": 2 }, { "label": "K", "x": 8.75, "y": 2 }, { "label": "L", "x": 9.75, "y": 2 }, { "label": ":", "x": 10.75, "y": 2 }, { "label": "\"", "x": 11.75, "y": 2 }, { "label": "Enter", "x": 12.75, "y": 2, "w": 2.25 }, + { "label": "Shift", "x": 0, "y": 3, "w": 2.25 }, { "label": "Z", "x": 2.25, "y": 3 }, { "label": "X", "x": 3.25, "y": 3 }, { "label": "C", "x": 4.25, "y": 3 }, { "label": "V", "x": 5.25, "y": 3 }, { "label": "B", "x": 6.25, "y": 3 }, { "label": "N", "x": 7.25, "y": 3 }, { "label": "M", "x": 8.25, "y": 3 }, { "label": "<", "x": 9.25, "y": 3 }, { "label": ">", "x": 10.25, "y": 3 }, { "label": "Shift", "x": 11.25, "y": 3, "w": 1.75 }, { "label": "Up", "x": 13, "y": 3 }, { "label": "Fn2", "x": 14, "y": 3 }, + { "label": "Ctrl", "x": 0, "y": 4, "w": 1.25 }, { "label": "Alt", "x": 1.25, "y": 4, "w": 1.25 }, { "label": "Win", "x": 2.5, "y": 4, "w": 1.25 }, { "label": "Space", "x": 3.75, "y": 4, "w": 6.25 }, { "label": "?", "x": 10, "y": 4 }, { "label": "Fn1", "x": 11, "y": 4 }, { "label": "Left", "x": 12, "y": 4 }, { "label": "Down", "x": 13, "y": 4 }, { "label": "Right", "x": 14, "y": 4 } + ] + } + } +} \ No newline at end of file diff --git a/keyboards/db/db63/keymaps/default/keymap.c b/keyboards/db/db63/keymaps/default/keymap.c new file mode 100644 index 0000000000..800ff960b1 --- /dev/null +++ b/keyboards/db/db63/keymaps/default/keymap.c @@ -0,0 +1,60 @@ +/* +Copyright 2020 Hung DO + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT( + KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + MO(3), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, MO(2), + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_SLSH, MO(1), KC_LEFT, KC_DOWN, KC_RGHT + ), + [1] = LAYOUT( + KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, _______, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, XXXXXXX, + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, MO(1), KC_LEFT, KC_DOWN, KC_RGHT + ), + [2] = LAYOUT( + KC_GESC, RGB_M_P, RGB_M_B, RGB_M_R, RGB_M_SW, RGB_M_SN, RGB_M_K, RGB_M_X, RGB_M_G, RGB_M_T, RGB_TOG, RGB_VAD, RGB_VAI, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + XXXXXXX, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, _______, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, MO(2), + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT + ), + [3] = LAYOUT( + _______, _______, _______, _______, _______, _______, _______, _______, BL_STEP, BL_BRTG, BL_TOGG, BL_DEC, BL_INC, _______, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + MO(3), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, RESET, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, XXXXXXX, + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT + ), +}; + +bool led_update_user(led_t led_state) { + if (led_state.caps_lock) { + rgblight_sethsv(HSV_CYAN); + writePinHigh(D1); + } else { + rgblight_sethsv(HSV_GREEN); + writePinLow(D1); + } + return false; +} diff --git a/keyboards/db/db63/rules.mk b/keyboards/db/db63/rules.mk new file mode 100644 index 0000000000..84eace5ed6 --- /dev/null +++ b/keyboards/db/db63/rules.mk @@ -0,0 +1,24 @@ +# MCU name +MCU = atmega32a + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = bootloadHID + +# build options +BOOTMAGIC_ENABLE = no +MOUSEKEY_ENABLE = yes +EXTRAKEY_ENABLE = yes +CONSOLE_ENABLE = no +COMMAND_ENABLE = yes +BACKLIGHT_ENABLE = yes +RGBLIGHT_ENABLE = yes +WS2812_DRIVER = i2c + +OPT_DEFS = -DDEBUG_LEVEL=0 diff --git a/keyboards/db/db63/usbconfig.h b/keyboards/db/db63/usbconfig.h new file mode 100644 index 0000000000..0dfe8b3baf --- /dev/null +++ b/keyboards/db/db63/usbconfig.h @@ -0,0 +1,383 @@ +/* Name: usbconfig.h + * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers + * Author: Christian Starkjohann + * Creation Date: 2005-04-01 + * Tabsize: 4 + * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH + * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) + * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $ + */ + +#pragma once + +#include "config.h" + +/* +General Description: +This file is an example configuration (with inline documentation) for the USB +driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is +also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may +wire the lines to any other port, as long as D+ is also wired to INT0 (or any +other hardware interrupt, as long as it is the highest level interrupt, see +section at the end of this file). +*/ + +/* ---------------------------- Hardware Config ---------------------------- */ + +#define USB_CFG_IOPORTNAME D +/* This is the port where the USB bus is connected. When you configure it to + * "B", the registers PORTB, PINB and DDRB will be used. + */ +#define USB_CFG_DMINUS_BIT 3 +/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. + * This may be any bit in the port. + */ +#define USB_CFG_DPLUS_BIT 2 +/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. + * This may be any bit in the port. Please note that D+ must also be connected + * to interrupt pin INT0! [You can also use other interrupts, see section + * "Optional MCU Description" below, or you can connect D- to the interrupt, as + * it is required if you use the USB_COUNT_SOF feature. If you use D- for the + * interrupt, the USB interrupt will also be triggered at Start-Of-Frame + * markers every millisecond.] + */ +#define USB_CFG_CLOCK_KHZ (F_CPU/1000) +/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, + * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code + * require no crystal, they tolerate +/- 1% deviation from the nominal + * frequency. All other rates require a precision of 2000 ppm and thus a + * crystal! + * Since F_CPU should be defined to your actual clock rate anyway, you should + * not need to modify this setting. + */ +#define USB_CFG_CHECK_CRC 0 +/* Define this to 1 if you want that the driver checks integrity of incoming + * data packets (CRC checks). CRC checks cost quite a bit of code size and are + * currently only available for 18 MHz crystal clock. You must choose + * USB_CFG_CLOCK_KHZ = 18000 if you enable this option. + */ + +/* ----------------------- Optional Hardware Config ------------------------ */ + +/* #define USB_CFG_PULLUP_IOPORTNAME D */ +/* If you connect the 1.5k pullup resistor from D- to a port pin instead of + * V+, you can connect and disconnect the device from firmware by calling + * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h). + * This constant defines the port on which the pullup resistor is connected. + */ +/* #define USB_CFG_PULLUP_BIT 4 */ +/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined + * above) where the 1.5k pullup resistor is connected. See description + * above for details. + */ + +/* --------------------------- Functional Range ---------------------------- */ + +#define USB_CFG_HAVE_INTRIN_ENDPOINT 1 +/* Define this to 1 if you want to compile a version with two endpoints: The + * default control endpoint 0 and an interrupt-in endpoint (any other endpoint + * number). + */ +#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1 +/* Define this to 1 if you want to compile a version with three endpoints: The + * default control endpoint 0, an interrupt-in endpoint 3 (or the number + * configured below) and a catch-all default interrupt-in endpoint as above. + * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature. + */ +#define USB_CFG_EP3_NUMBER 3 +/* If the so-called endpoint 3 is used, it can now be configured to any other + * endpoint number (except 0) with this macro. Default if undefined is 3. + */ +/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */ +/* The above macro defines the startup condition for data toggling on the + * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1. + * Since the token is toggled BEFORE sending any data, the first packet is + * sent with the oposite value of this configuration! + */ +#define USB_CFG_IMPLEMENT_HALT 0 +/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature + * for endpoint 1 (interrupt endpoint). Although you may not need this feature, + * it is required by the standard. We have made it a config option because it + * bloats the code considerably. + */ +#define USB_CFG_SUPPRESS_INTR_CODE 0 +/* Define this to 1 if you want to declare interrupt-in endpoints, but don't + * want to send any data over them. If this macro is defined to 1, functions + * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if + * you need the interrupt-in endpoints in order to comply to an interface + * (e.g. HID), but never want to send any data. This option saves a couple + * of bytes in flash memory and the transmit buffers in RAM. + */ +#define USB_CFG_IS_SELF_POWERED 0 +/* Define this to 1 if the device has its own power supply. Set it to 0 if the + * device is powered from the USB bus. + */ +#define USB_CFG_IMPLEMENT_FN_WRITE 1 +/* Set this to 1 if you want usbFunctionWrite() to be called for control-out + * transfers. Set it to 0 if you don't need it and want to save a couple of + * bytes. + */ +#define USB_CFG_IMPLEMENT_FN_READ 0 +/* Set this to 1 if you need to send control replies which are generated + * "on the fly" when usbFunctionRead() is called. If you only want to send + * data from a static buffer, set it to 0 and return the data from + * usbFunctionSetup(). This saves a couple of bytes. + */ +#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 +/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. + * You must implement the function usbFunctionWriteOut() which receives all + * interrupt/bulk data sent to any endpoint other than 0. The endpoint number + * can be found in 'usbRxToken'. + */ +#define USB_CFG_HAVE_FLOWCONTROL 0 +/* Define this to 1 if you want flowcontrol over USB data. See the definition + * of the macros usbDisableAllRequests() and usbEnableAllRequests() in + * usbdrv.h. + */ +#define USB_CFG_DRIVER_FLASH_PAGE 0 +/* If the device has more than 64 kBytes of flash, define this to the 64 k page + * where the driver's constants (descriptors) are located. Or in other words: + * Define this to 1 for boot loaders on the ATMega128. + */ +#define USB_CFG_LONG_TRANSFERS 0 +/* Define this to 1 if you want to send/receive blocks of more than 254 bytes + * in a single control-in or control-out transfer. Note that the capability + * for long transfers increases the driver size. + */ +/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */ +/* This macro is a hook if you want to do unconventional things. If it is + * defined, it's inserted at the beginning of received message processing. + * If you eat the received message and don't want default processing to + * proceed, do a return after doing your things. One possible application + * (besides debugging) is to flash a status LED on each packet. + */ +/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */ +/* This macro is a hook if you need to know when an USB RESET occurs. It has + * one parameter which distinguishes between the start of RESET state and its + * end. + */ +/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */ +/* This macro (if defined) is executed when a USB SET_ADDRESS request was + * received. + */ +#define USB_COUNT_SOF 1 +/* define this macro to 1 if you need the global variable "usbSofCount" which + * counts SOF packets. This feature requires that the hardware interrupt is + * connected to D- instead of D+. + */ +/* #ifdef __ASSEMBLER__ + * macro myAssemblerMacro + * in YL, TCNT0 + * sts timer0Snapshot, YL + * endm + * #endif + * #define USB_SOF_HOOK myAssemblerMacro + * This macro (if defined) is executed in the assembler module when a + * Start Of Frame condition is detected. It is recommended to define it to + * the name of an assembler macro which is defined here as well so that more + * than one assembler instruction can be used. The macro may use the register + * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages + * immediately after an SOF pulse may be lost and must be retried by the host. + * What can you do with this hook? Since the SOF signal occurs exactly every + * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in + * designs running on the internal RC oscillator. + * Please note that Start Of Frame detection works only if D- is wired to the + * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! + */ +#define USB_CFG_CHECK_DATA_TOGGLING 0 +/* define this macro to 1 if you want to filter out duplicate data packets + * sent by the host. Duplicates occur only as a consequence of communication + * errors, when the host does not receive an ACK. Please note that you need to + * implement the filtering yourself in usbFunctionWriteOut() and + * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable + * for each control- and out-endpoint to check for duplicate packets. + */ +#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 +/* define this macro to 1 if you want the function usbMeasureFrameLength() + * compiled in. This function can be used to calibrate the AVR's RC oscillator. + */ +#define USB_USE_FAST_CRC 0 +/* The assembler module has two implementations for the CRC algorithm. One is + * faster, the other is smaller. This CRC routine is only used for transmitted + * messages where timing is not critical. The faster routine needs 31 cycles + * per byte while the smaller one needs 61 to 69 cycles. The faster routine + * may be worth the 32 bytes bigger code size if you transmit lots of data and + * run the AVR close to its limit. + */ + +/* -------------------------- Device Description --------------------------- */ + +#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF) +/* USB vendor ID for the device, low byte first. If you have registered your + * own Vendor ID, define it here. Otherwise you may use one of obdev's free + * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF) +/* This is the ID of the product, low byte first. It is interpreted in the + * scope of the vendor ID. If you have registered your own VID with usb.org + * or if you have licensed a PID from somebody else, define it here. Otherwise + * you may use one of obdev's free shared VID/PID pairs. See the file + * USB-IDs-for-free.txt for details! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_VERSION (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF) +/* Version number of the device: Minor number first, then major number. + */ +#define USB_CFG_VENDOR_NAME 'H', 'N', 'B' +#define USB_CFG_VENDOR_NAME_LEN 3 +/* These two values define the vendor name returned by the USB device. The name + * must be given as a list of characters under single quotes. The characters + * are interpreted as Unicode (UTF-16) entities. + * If you don't want a vendor name string, undefine these macros. + * ALWAYS define a vendor name containing your Internet domain name if you use + * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for + * details. + */ +#define USB_CFG_DEVICE_NAME 'D', 'B', '6', '3', 'H', 'S' +#define USB_CFG_DEVICE_NAME_LEN 6 +/* Same as above for the device name. If you don't want a device name, undefine + * the macros. See the file USB-IDs-for-free.txt before you assign a name if + * you use a shared VID/PID. + */ +/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */ +/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */ +/* Same as above for the serial number. If you don't want a serial number, + * undefine the macros. + * It may be useful to provide the serial number through other means than at + * compile time. See the section about descriptor properties below for how + * to fine tune control over USB descriptors such as the string descriptor + * for the serial number. + */ +#define USB_CFG_DEVICE_CLASS 0 +#define USB_CFG_DEVICE_SUBCLASS 0 +/* See USB specification if you want to conform to an existing device class. + * Class 0xff is "vendor specific". + */ +#define USB_CFG_INTERFACE_CLASS 3 /* HID */ +#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */ +#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */ +/* See USB specification if you want to conform to an existing device class or + * protocol. The following classes must be set at interface level: + * HID class is 3, no subclass and protocol required (but may be useful!) + * CDC class is 2, use subclass 2 and protocol 1 for ACM + */ +#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 +/* Define this to the length of the HID report descriptor, if you implement + * an HID device. Otherwise don't define it or define it to 0. + * If you use this define, you must add a PROGMEM character array named + * "usbHidReportDescriptor" to your code which contains the report descriptor. + * Don't forget to keep the array and this define in sync! + */ + +/* #define USB_PUBLIC static */ +/* Use the define above if you #include usbdrv.c instead of linking against it. + * This technique saves a couple of bytes in flash memory. + */ + +/* ------------------- Fine Control over USB Descriptors ------------------- */ +/* If you don't want to use the driver's default USB descriptors, you can + * provide our own. These can be provided as (1) fixed length static data in + * flash memory, (2) fixed length static data in RAM or (3) dynamically at + * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more + * information about this function. + * Descriptor handling is configured through the descriptor's properties. If + * no properties are defined or if they are 0, the default descriptor is used. + * Possible properties are: + * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched + * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is + * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if + * you want RAM pointers. + * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found + * in static memory is in RAM, not in flash memory. + * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash), + * the driver must know the descriptor's length. The descriptor itself is + * found at the address of a well known identifier (see below). + * List of static descriptor names (must be declared PROGMEM if in flash): + * char usbDescriptorDevice[]; + * char usbDescriptorConfiguration[]; + * char usbDescriptorHidReport[]; + * char usbDescriptorString0[]; + * int usbDescriptorStringVendor[]; + * int usbDescriptorStringDevice[]; + * int usbDescriptorStringSerialNumber[]; + * Other descriptors can't be provided statically, they must be provided + * dynamically at runtime. + * + * Descriptor properties are or-ed or added together, e.g.: + * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18)) + * + * The following descriptors are defined: + * USB_CFG_DESCR_PROPS_DEVICE + * USB_CFG_DESCR_PROPS_CONFIGURATION + * USB_CFG_DESCR_PROPS_STRINGS + * USB_CFG_DESCR_PROPS_STRING_0 + * USB_CFG_DESCR_PROPS_STRING_VENDOR + * USB_CFG_DESCR_PROPS_STRING_PRODUCT + * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER + * USB_CFG_DESCR_PROPS_HID + * USB_CFG_DESCR_PROPS_HID_REPORT + * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver) + * + * Note about string descriptors: String descriptors are not just strings, they + * are Unicode strings prefixed with a 2 byte header. Example: + * int serialNumberDescriptor[] = { + * USB_STRING_DESCRIPTOR_HEADER(6), + * 'S', 'e', 'r', 'i', 'a', 'l' + * }; + */ + +#define USB_CFG_DESCR_PROPS_DEVICE 0 +#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 +#define USB_CFG_DESCR_PROPS_STRINGS 0 +#define USB_CFG_DESCR_PROPS_STRING_0 0 +#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 +#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 +#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 +#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID 0 +#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID_REPORT 0 +#define USB_CFG_DESCR_PROPS_UNKNOWN 0 + +#define usbMsgPtr_t unsigned short +/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to + * a scalar type here because gcc generates slightly shorter code for scalar + * arithmetics than for pointer arithmetics. Remove this define for backward + * type compatibility or define it to an 8 bit type if you use data in RAM only + * and all RAM is below 256 bytes (tiny memory model in IAR CC). + */ + +/* ----------------------- Optional MCU Description ------------------------ */ + +/* The following configurations have working defaults in usbdrv.h. You + * usually don't need to set them explicitly. Only if you want to run + * the driver on a device which is not yet supported or with a compiler + * which is not fully supported (such as IAR C) or if you use a differnt + * interrupt than INT0, you may have to define some of these. + */ +/* #define USB_INTR_CFG MCUCR */ +/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */ +/* #define USB_INTR_CFG_CLR 0 */ +/* #define USB_INTR_ENABLE GIMSK */ +/* #define USB_INTR_ENABLE_BIT INT0 */ +/* #define USB_INTR_PENDING GIFR */ +/* #define USB_INTR_PENDING_BIT INTF0 */ +/* #define USB_INTR_VECTOR INT0_vect */ + +/* Set INT1 for D- falling edge to count SOF */ +/* #define USB_INTR_CFG EICRA */ +#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10)) +/* #define USB_INTR_CFG_CLR 0 */ +/* #define USB_INTR_ENABLE EIMSK */ +#define USB_INTR_ENABLE_BIT INT1 +/* #define USB_INTR_PENDING EIFR */ +#define USB_INTR_PENDING_BIT INTF1 +#define USB_INTR_VECTOR INT1_vect -- cgit v1.2.3