From de4a47f1cc28c4ef66e7560eac2a50f717070ae2 Mon Sep 17 00:00:00 2001 From: fauxpark Date: Sat, 21 Sep 2019 15:06:32 +1000 Subject: Cleanup rules.mk for 32A and 328P keyboards (#6767) --- keyboards/coseyfannitutti/discipline/rules.mk | 52 ++------------------------- 1 file changed, 3 insertions(+), 49 deletions(-) (limited to 'keyboards/coseyfannitutti') diff --git a/keyboards/coseyfannitutti/discipline/rules.mk b/keyboards/coseyfannitutti/discipline/rules.mk index bc81342de2..24b5969b74 100644 --- a/keyboards/coseyfannitutti/discipline/rules.mk +++ b/keyboards/coseyfannitutti/discipline/rules.mk @@ -1,61 +1,19 @@ # MCU name MCU = atmega32a -PROTOCOL = VUSB -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. +# Processor frequency F_CPU = 16000000 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID -# -# This uses usbaspbootloader +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = USBasp -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 - # Flash program via avrdude, but default command is not suitable. # You can use plaid:default:program PROGRAM_CMD = avrdude -c usbasp -p m32 -U flash:w:$(BUILD_DIR)/$(TARGET).hex @@ -84,8 +42,4 @@ AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) -# unsupported features for now -NO_UART = yes -NO_SUSPEND_POWER_DOWN = yes - LAYOUTS = 65_ansi -- cgit v1.2.3