From a5b1af4999345239df5086351b52a5b4d2daa97e Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sat, 27 Aug 2016 18:40:50 +0300 Subject: Normalize line endings --- .../chibios_test/boards/GENERIC_STM32_F103/board.c | 98 +++--- .../chibios_test/boards/GENERIC_STM32_F103/board.h | 332 ++++++++++----------- .../boards/GENERIC_STM32_F103/board.mk | 10 +- 3 files changed, 220 insertions(+), 220 deletions(-) (limited to 'keyboards/chibios_test/boards') diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c index 31319ef575..2809c9d184 100644 --- a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c +++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c @@ -1,49 +1,49 @@ -/* - ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#include "hal.h" - -/** - * @brief PAL setup. - * @details Digital I/O ports static configuration as defined in @p board.h. - * This variable is used by the HAL when initializing the PAL driver. - */ -#if HAL_USE_PAL || defined(__DOXYGEN__) -const PALConfig pal_default_config = -{ - {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, - {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, - {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, - {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, - {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, -}; -#endif - -/* - * Early initialization code. - * This initialization must be performed just after stack setup and before - * any other initialization. - */ -void __early_init(void) { - - stm32_clock_init(); -} - -/* - * Board-specific initialization code. - */ -void boardInit(void) { -} +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#include "hal.h" + +/** + * @brief PAL setup. + * @details Digital I/O ports static configuration as defined in @p board.h. + * This variable is used by the HAL when initializing the PAL driver. + */ +#if HAL_USE_PAL || defined(__DOXYGEN__) +const PALConfig pal_default_config = +{ + {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, + {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, + {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, + {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, + {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, +}; +#endif + +/* + * Early initialization code. + * This initialization must be performed just after stack setup and before + * any other initialization. + */ +void __early_init(void) { + + stm32_clock_init(); +} + +/* + * Board-specific initialization code. + */ +void boardInit(void) { +} diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h index 7253e77826..b31d74307b 100644 --- a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h +++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h @@ -1,166 +1,166 @@ -/* - ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#ifndef _BOARD_H_ -#define _BOARD_H_ - -/* - * Setup for a Generic STM32F103 board. - */ - -/* - * Board identifier. - */ -#define BOARD_GENERIC_STM32_F103 -#define BOARD_NAME "Generic STM32F103x board" - -/* - * Board frequencies. - */ -#define STM32_LSECLK 32768 -#define STM32_HSECLK 8000000 - -/* - * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. - */ -#define STM32F103xB - -/* - * IO pins assignments - */ - -/* on-board */ - -#define GPIOC_LED 13 -#define GPIOD_OSC_IN 0 -#define GPIOD_OSC_OUT 1 - -/* In case your board has a "USB enable" hardware - controlled by a pin, define it here. (It could be just - a 1.5k resistor connected to D+ line.) -*/ -/* -#define GPIOB_USB_DISC 10 -*/ - -/* - * I/O ports initial setup, this configuration is established soon after reset - * in the initialization code. - * - * The digits have the following meaning: - * 0 - Analog input. - * 1 - Push Pull output 10MHz. - * 2 - Push Pull output 2MHz. - * 3 - Push Pull output 50MHz. - * 4 - Digital input. - * 5 - Open Drain output 10MHz. - * 6 - Open Drain output 2MHz. - * 7 - Open Drain output 50MHz. - * 8 - Digital input with PullUp or PullDown resistor depending on ODR. - * 9 - Alternate Push Pull output 10MHz. - * A - Alternate Push Pull output 2MHz. - * B - Alternate Push Pull output 50MHz. - * C - Reserved. - * D - Alternate Open Drain output 10MHz. - * E - Alternate Open Drain output 2MHz. - * F - Alternate Open Drain output 50MHz. - * Please refer to the STM32 Reference Manual for details. - */ - -/* - * Port A setup. - * Everything input with pull-up except: - * PA2 - Alternate output (USART2 TX). - * PA3 - Normal input (USART2 RX). - * PA9 - Alternate output (USART1 TX). - * PA10 - Normal input (USART1 RX). - */ -#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */ -#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ -#define VAL_GPIOAODR 0xFFFFFFFF - -/* - * Port B setup. - * Everything input with pull-up except: - * PB10 - Push Pull output (USB switch). - */ -#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ -#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */ -#define VAL_GPIOBODR 0xFFFFFFFF - -/* - * Port C setup. - * Everything input with pull-up except: - * PC13 - Push Pull output (LED). - */ -#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ -#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */ -#define VAL_GPIOCODR 0xFFFFFFFF - -/* - * Port D setup. - * Everything input with pull-up except: - * PD0 - Normal input (XTAL). - * PD1 - Normal input (XTAL). - */ -#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ -#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ -#define VAL_GPIODODR 0xFFFFFFFF - -/* - * Port E setup. - * Everything input with pull-up except: - */ -#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ -#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ -#define VAL_GPIOEODR 0xFFFFFFFF - -/* - * USB bus activation macro, required by the USB driver. - */ -/* The point is that most of the generic STM32F103* boards - have a 1.5k resistor connected on one end to the D+ line - and on the other end to some pin. Or even a slightly more - complicated "USB enable" circuit, controlled by a pin. - That should go here. - - However on some boards (e.g. one that I have), there's no - such hardware. In which case it's better to not do anything. -*/ -/* -#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC) -*/ -#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT); - -/* - * USB bus de-activation macro, required by the USB driver. - */ -/* -#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC) -*/ -#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12); - -#if !defined(_FROM_ASM_) -#ifdef __cplusplus -extern "C" { -#endif - void boardInit(void); -#ifdef __cplusplus -} -#endif -#endif /* _FROM_ASM_ */ - -#endif /* _BOARD_H_ */ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +/* + * Setup for a Generic STM32F103 board. + */ + +/* + * Board identifier. + */ +#define BOARD_GENERIC_STM32_F103 +#define BOARD_NAME "Generic STM32F103x board" + +/* + * Board frequencies. + */ +#define STM32_LSECLK 32768 +#define STM32_HSECLK 8000000 + +/* + * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. + */ +#define STM32F103xB + +/* + * IO pins assignments + */ + +/* on-board */ + +#define GPIOC_LED 13 +#define GPIOD_OSC_IN 0 +#define GPIOD_OSC_OUT 1 + +/* In case your board has a "USB enable" hardware + controlled by a pin, define it here. (It could be just + a 1.5k resistor connected to D+ line.) +*/ +/* +#define GPIOB_USB_DISC 10 +*/ + +/* + * I/O ports initial setup, this configuration is established soon after reset + * in the initialization code. + * + * The digits have the following meaning: + * 0 - Analog input. + * 1 - Push Pull output 10MHz. + * 2 - Push Pull output 2MHz. + * 3 - Push Pull output 50MHz. + * 4 - Digital input. + * 5 - Open Drain output 10MHz. + * 6 - Open Drain output 2MHz. + * 7 - Open Drain output 50MHz. + * 8 - Digital input with PullUp or PullDown resistor depending on ODR. + * 9 - Alternate Push Pull output 10MHz. + * A - Alternate Push Pull output 2MHz. + * B - Alternate Push Pull output 50MHz. + * C - Reserved. + * D - Alternate Open Drain output 10MHz. + * E - Alternate Open Drain output 2MHz. + * F - Alternate Open Drain output 50MHz. + * Please refer to the STM32 Reference Manual for details. + */ + +/* + * Port A setup. + * Everything input with pull-up except: + * PA2 - Alternate output (USART2 TX). + * PA3 - Normal input (USART2 RX). + * PA9 - Alternate output (USART1 TX). + * PA10 - Normal input (USART1 RX). + */ +#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */ +#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ +#define VAL_GPIOAODR 0xFFFFFFFF + +/* + * Port B setup. + * Everything input with pull-up except: + * PB10 - Push Pull output (USB switch). + */ +#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ +#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */ +#define VAL_GPIOBODR 0xFFFFFFFF + +/* + * Port C setup. + * Everything input with pull-up except: + * PC13 - Push Pull output (LED). + */ +#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ +#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */ +#define VAL_GPIOCODR 0xFFFFFFFF + +/* + * Port D setup. + * Everything input with pull-up except: + * PD0 - Normal input (XTAL). + * PD1 - Normal input (XTAL). + */ +#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ +#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ +#define VAL_GPIODODR 0xFFFFFFFF + +/* + * Port E setup. + * Everything input with pull-up except: + */ +#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ +#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ +#define VAL_GPIOEODR 0xFFFFFFFF + +/* + * USB bus activation macro, required by the USB driver. + */ +/* The point is that most of the generic STM32F103* boards + have a 1.5k resistor connected on one end to the D+ line + and on the other end to some pin. Or even a slightly more + complicated "USB enable" circuit, controlled by a pin. + That should go here. + + However on some boards (e.g. one that I have), there's no + such hardware. In which case it's better to not do anything. +*/ +/* +#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT); + +/* + * USB bus de-activation macro, required by the USB driver. + */ +/* +#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12); + +#if !defined(_FROM_ASM_) +#ifdef __cplusplus +extern "C" { +#endif + void boardInit(void); +#ifdef __cplusplus +} +#endif +#endif /* _FROM_ASM_ */ + +#endif /* _BOARD_H_ */ diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk index d692c0ee46..48e0e51fe6 100644 --- a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk +++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk @@ -1,5 +1,5 @@ -# List of all the board related files. -BOARDSRC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103/board.c - -# Required include directories -BOARDINC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103 +# List of all the board related files. +BOARDSRC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103/board.c + +# Required include directories +BOARDINC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103 -- cgit v1.2.3