diff options
Diffstat (limited to 'keyboards/phantom')
| -rw-r--r-- | keyboards/phantom/Makefile | 75 | ||||
| -rw-r--r-- | keyboards/phantom/keymaps/xyverz/keymap.c | 104 | ||||
| -rw-r--r-- | keyboards/phantom/rules.mk | 69 |
3 files changed, 175 insertions, 73 deletions
diff --git a/keyboards/phantom/Makefile b/keyboards/phantom/Makefile index 3a71fd0ee3..4e2a6f00fd 100644 --- a/keyboards/phantom/Makefile +++ b/keyboards/phantom/Makefile @@ -1,74 +1,3 @@ - - -SRC = led.c - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -RGBLIGHT_ENABLE ?=yes # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality (+1150) -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/phantom/keymaps/xyverz/keymap.c b/keyboards/phantom/keymaps/xyverz/keymap.c new file mode 100644 index 0000000000..4a15226386 --- /dev/null +++ b/keyboards/phantom/keymaps/xyverz/keymap.c @@ -0,0 +1,104 @@ +#include "phantom.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + + +// Used for SHIFT_ESC +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QW 0 +#define _DV 1 +#define _CM 2 +#define _FL 3 + +// Macro name shortcuts +#define QWERTY M(_QW) +#define DVORAK M(_DV) +#define COLEMAK M(_CM) + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[_QW] = { /* Layer 0: Qwerty */ + {KC_ESC, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS}, + {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, XXXXXXX, KC_BSPC, KC_INS, KC_HOME, KC_PGUP}, + {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN}, + {KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, XXXXXXX, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX}, + {KC_LSFT, XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, XXXXXXX, KC_RSFT, XXXXXXX, KC_UP, XXXXXXX}, + {KC_LCTL, KC_LALT, KC_LGUI, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, XXXXXXX, KC_RGUI, KC_RALT, KC_RCTL, MO(_FL), KC_LEFT, KC_DOWN, KC_RGHT} + }, + +[_DV] = { /* Layer 1: Dvorak */ + {KC_ESC, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS}, + {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_LBRC, KC_RBRC, XXXXXXX, KC_BSPC, KC_INS, KC_HOME, KC_PGUP}, + {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_SLSH, KC_EQL, KC_BSLS, KC_DEL, KC_END, KC_PGDN}, + {KC_CAPS, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_MINS, XXXXXXX, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX}, + {KC_LSFT, XXXXXXX, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, XXXXXXX, KC_RSFT, XXXXXXX, KC_UP, XXXXXXX}, + {KC_LCTL, KC_LALT, KC_LGUI, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, XXXXXXX, KC_RGUI, KC_RALT, KC_RCTL, MO(_FL), KC_LEFT, KC_DOWN, KC_RGHT} + }, + +[_CM] = { /* Layer 2: Colemak */ + {KC_ESC, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS}, + {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, XXXXXXX, KC_BSPC, KC_INS, KC_HOME, KC_PGUP}, + {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN}, + {KC_BSPC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT, XXXXXXX, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX}, + {KC_LSFT, XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, XXXXXXX, KC_RSFT, XXXXXXX, KC_UP, XXXXXXX}, + {KC_LCTL, KC_LALT, KC_LGUI, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, XXXXXXX, KC_RGUI, KC_RALT, KC_RCTL, MO(_FL), KC_LEFT, KC_DOWN, KC_RGHT} + }, + +[_FL] = { /* Layer 3: Functions */ + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, XXXXXXX, RESET, KC_MPRV, KC_MPLY, KC_MNXT}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, KC_VOLD, KC_VOLU}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, XXXXXXX, _______, XXXXXXX, XXXXXXX, XXXXXXX}, + {_______, XXXXXXX, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, XXXXXXX, _______, XXXXXXX, _______, XXXXXXX}, + {QWERTY, DVORAK, COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______, _______, _______}, + }, + + +}; + +enum function_id { + SHIFT_ESC, +}; + + +const uint16_t PROGMEM fn_actions[] = { + +}; + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + switch(id) { + case _DV: + if (record->event.pressed) { + persistant_default_layer_set(1UL<<_DV); + } + break; + case _QW: + if (record->event.pressed) { + persistant_default_layer_set(1UL<<_QW); + } + break; + case _CM: + if (record->event.pressed) { + persistant_default_layer_set(1UL<<_CM); + } + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/phantom/rules.mk b/keyboards/phantom/rules.mk new file mode 100644 index 0000000000..c6b8ca6c35 --- /dev/null +++ b/keyboards/phantom/rules.mk @@ -0,0 +1,69 @@ + + +SRC = led.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE ?=yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID |